SECO-LARM USA EV-122C-DXB3Q User Manual

SECO-LARM BALL-MOUNT IR DOME CAMERA Manual

TROUBLE SHOOTING

The screen is blank

• Check that the camera is powered up.

• Check that the monitor is powered up.

• Check that the video cable connecting the camera to the monitor is connected properly.

SECO -LARM

The screen image is dim

The screen image has poor contrast

The screen image flickers

The screen image is distorted

The camera case is hot

IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national,

state, and local laws and statutes related to monitoring and recording audio and video signals.
responsible for the use of this product in violation of any current laws or statutes.

WARNING Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or

electric shock. Do not open the case of this device, as there are no field-serviceable components inside.

FCC COMPLIANCE STATEMENT

the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARRANTY

service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited
to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that
such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal
or property damages of any kind to the purchaser or anyone else.

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.

This SECO-LARM product is warranted against defects in material and workmanship while used in normal

• Clean the lens (using a soft, clean cloth).

• Check that the light source is adequate.

• Adjust the monitor’s contrast knob.

• Change the position of the camera.

• Change the position of the camera.

• Change the position of the camera.

• Check that the correct power supply is in use.

SECO-LARM

Information to the user: This equipment has been tested and found to comply with

will not be held

EV-122C-DXB3Q

Multi-Axis Ball-Mount Color Dome Camera

MANUAL

Multi-Axis ball mount for

•

wall or ceiling mounting
360° Rotation, 10°~120° tilt

•

1/3” Sony Super HAD II CCD

•

3.6mm Lens

•

24 IR LEDs

•

50ft (15m) IR range

•

Concealed wiring

•

C .- M ., I

SECO-LARM U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Tel: [phone] Fax: [phone]

Website: www.seco-larm.com
E-mail: [e-mail]

®

MiEV-122C-DXB3Q_0914b.pmd

PICSN4

Note: Products with model number that ends with "Q" or have a round green "Q" sticker represents RoHS compliant products.

SECO-LARM BALL-MOUNT IR DOME CAMERA Manual SECO-LARM BALL-MOUNT IR DOME CAMERA Manual

Specifications

____________________________________________________________________________________________________

Type

____________________________________________________________________________________________________

Chip

___________________________________________________________________________________________________________________________________________________________________________________________________________________________

Resolution

____________________________________________________________________________________________________

Pickup elements

____________________________________________________________________________________________________

Scanning system

____________________________________________________________________________________________________

Sync

____________________________________________________________________________________________________

Video output

____________________________________________________________________________________________________

Lens

____________________________________________________________________________________________________

IR LEDs

____________________________________________________________________________________________________

IR distance

____________________________________________________________________________________________________

IR view angle

____________________________________________________________________________________________________

Minimum illumination

____________________________________________________________________________________________________

Gamma correction

____________________________________________________________________________________________________

S/N ratio

____________________________________________________________________________________________________

Shutter control

____________________________________________________________________________________________________

Automatic gain control

____________________________________________________________________________________________________

White balance

____________________________________________________________________________________________________

Power source

________________________________________________________________________________________________________________________________________________________________________________________________________

Power consumption

____________________________________________________________________________________________________

Storage temperature

____________________________________________________________________________________________________

Operating temperature

____________________________________________________________________________________________________

Dimensions

____________________________________________________________________________________________________

Weight

____________________________________________________________________________________________________

Auto Electronic Shutter (AES) 1/60~1/100,000 sec. (NTSC)

EV-122C-DXB3Q (NTSC)

Color camera

1/3” Sony Super HAD II CCD

420 TV lines

510x492 pixels

2:1 interlace, V: 60Hz, H: 15.734KHz

Internal

1.0Vp~p composite output, 75 ohms

F1 2, 3.6 mm (lens included)

24

Up to 50 ft. (15 m)

50o~80o Beam spread, 30o per LED

0 05 lux, (0 lux with IR on)

0.45

>50dB

Auto

Auto, 2500o~9500o K

12 VDC ±10%

70 mA LEDs off, 200 mA LEDs on

-4°~122° F (-20°~50° C)

14°~122° F (-10°~50° C)

311/16” x 211/16” (93 x 69 mm)

6 oz. (170 g)

Dimensions:

CA-161T - DC plug included.

To BNC

(From DC
Camera) (CA-161T)

3 x

Screws

Camera

Case

BEFORE STARTING

1. Please read this manual carefully and keep it for future reference.

2. Use the camera within given temperature and electrical limits.

3. Do not mount the camera where it is exposed to rain or other
moisture, or in humid or dusty places.

4. Do not point the camera at the sun. Heat could damage the
camera, even when not in use.

5. Do not mount the camera in areas exposed to radiation, strong
magnetic fields, or strong electrical signals.*

Ball

Case

6. Do not open or disassemble the camera. There are no user-

7. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromagnetic

Parts List

1 x Camera Ball
1 x Case (2-part construction)
1 x Base
3 x Screws
1 x Manual
1 x DC plug with terminal block

Power

Connector

BNC

Connector

Base

serviceable parts inside.

fields close to the display CRT, especially when the monitor is
turned on or during de-Gaussing, which occurs automatically
with many monitors when the monitor is turned on.

311/16” (93mm)

211/16”

(69mm)

INSTALLATION

1. Run a 12VDC power supply wire and a video cable with a male
BNC connector through the wall to where the camera is to be
mounted.

2. Temporarily connect the camera to the 12VDC power supply.

3. Temporarily connect the camera’s female BNC connector to the
video cable’s male BNC connector.

4. While watching the monitor, hold the camera against the wall by
hand where it is to be mounted, then turn the camera until it is
certain that this mounting location is correct. Use a pencil to
mark the location of the three screw holes in the base.

5. Disconnect the 12VDC power supply and video cable.

6. Mount the bracket to the wall using the three included mounting
screws. If the wall is made of dry wall, brick, or similar material,
it may be necessary to use screw anchors (not included).

7. Reconnect the 12VDC power supply and video cable. Turn the
monitor on, and make sure the camera is sending the proper
video signal.

8. Adjust the camera angle.

9. Put the case over the camera ball and twist to secure to the
base.

10.Do a final test of the video camera and monitor.

* Note: The base also allows flush-mounting of the camera.

However, for the best security , run the wires through the wall.