SECO-LARM USA EV-122C-DVB3Q User Manual

ENFORCER Ball-Mount Indoor/Outdoor IR Camera Manual ENFORCER Ball-Mount Indoor/Outdoor IR Camera Manual

TROUBLE SHOOTING

The screen is blank

The screen image is dim

The screen image has poor
contrast

The screen image flickers
The screen image is distorted
The camera case is hot

IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all
national, state, and local laws and statutes related to monitoring and recording audio and video signals.

SECO-LARM

WARNING Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or
electric shock. Do not open the case of this device, as there are no field-serviceable components inside.

FCC COMPLIANCE STATEMENT

limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

will not be held responsible for the use of this product in violation of any current laws or statutes.

• Check that the camera is powered up.

• Check that the monitor is powered up.

• Check that the video cable connecting the camera to the monitor is connected properly.

• Clean the lens (using a soft, clean cloth).

• Check that the light source is adequate.

• Adjust the monitor’s contrast knob.

• Change the position of the camera.

• Change the position of the camera.

• Change the position of the camera.

• Check that the correct power supply is in use.

Information to the user: This equipment has been tested and found to comply with the

ENFORCER

VIDEO

MANUAL

EV-122C-DVB3Q

Color Ball-Mount Vandal-Resistent

Indoor/Outdoor IR Dome Camera with

24 LEDs and Split Glass Technology

®

WARRANTY

normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to
SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2008 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
or in part, without the written permission of SECO-LARM.

This SECO-LARM product is warranted against defects in material and workmanship while used in

SECO-LARM® U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]

Website: www.seco-larm.com
E-mail: [e-mail]

®

iMUIRVandalBallMntSmallCam.pmd

PICSN4

®®

®

SECO-LARMSECO-LARM

SECO-LARM

SECO-LARMSECO-LARM

Note: Products with a model number that ends with “Q” or which have a round green “Q” sticker are RoHS compliant.

®®

ENFORCER Ball-Mount Indoor/Outdoor IR Camera Manual ENFORCER Ball-Mount Indoor/Outdoor IR Camera Manual

Specifications

_______________________________________________________________________________________________________________________________________________________________

Type

_______________________________________________________________________________________________________________________________________________________________

Chip

_______________________________________________________________________________________________________________________________________________________________

Resolution

_______________________________________________________________________________________________________________________________________________________________

Pickup elements

_______________________________________________________________________________________________________________________________________________________________

Scanning system

_______________________________________________________________________________________________________________________________________________________________

Sync

_______________________________________________________________________________________________________________________________________________________________

Video output

_______________________________________________________________________________________________________________________________________________________________

Lens

_______________________________________________________________________________________________________________________________________________________________

IR LEDs

_______________________________________________________________________________________________________________________________________________________________

IR distance

_______________________________________________________________________________________________________________________________________________________________

IR view angle

_______________________________________________________________________________________________________________________________________________________________

Minimum illumination

_______________________________________________________________________________________________________________________________________________________________

Gamma correction

_______________________________________________________________________________________________________________________________________________________________

S/N ratio

_______________________________________________________________________________________________________________________________________________________________

Shutter control

_______________________________________________________________________________________________________________________________________________________________

Automatic gain control

_______________________________________________________________________________________________________________________________________________________________

White balance

_______________________________________________________________________________________________________________________________________________________________

Power source

_______________________________________________________________________________________________________________________________________________________________

Power consumption

_______________________________________________________________________________________________________________________________________________________________

Operating temperature

_______________________________________________________________________________________________________________________________________________________________

Enclosure

_______________________________________________________________________________________________________________________________________________________________

Dimensions

_______________________________________________________________________________________________________________________________________________________________

Weight

_______________________________________________________________________________________________________________________________________________________________

Cable length

_______________________________________________________________________________________________________________________________________________________________

EV-122C-DVB3Q

Ball-Mount Color Dome Camera

1/3” CCD, Sony

420 TV lines

510 x 492 pixels

2:1 interlace, V: 59.94Hz, H: 15.734KHz

Internal

1V p-p composite output, 75 ohms

3.6mm, F2.0

24 x LEDs (850nm)

Up to 50’ (15m)

o

56

0.5 lux (0 lux with IR on)

0.45

>48dB

Auto Electronic Shutter (AES), 1/60~1/100,000 sec.

Auto

Auto

12VDC ±10%

120mA (IR off), 400mA (IR on)

4°~122° F (-20°~50° C)

IP66 weatherproof

311/16” x 35/32” (94 x 80mm)

0.9 lb. (400g)

38” (98cm.)

Dimensions:

DC plug included.

To BNC

(From DC
camera)

Case

DC plug with

terminal block

Camera

Ball

Before Starting:

1. Please read this manual carefully and keep it for future
reference.

2. Use the camera within given temperature and electrical
limits.

3. While the camera is weatherproof to IP66 standard, do
not mount the camera where it is exposed to rain or other
moisture, or in humid or dusty places.

4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.

5. Do not mount the camera in areas exposed to radiation,

Parts List

1 x Camera Ball
1 x Case
1 x Base
4 x Screws with wall anchors
1 x Hex wrench
1 x Manual
1 x DC plug with terminal block

4 x

Screws

6. Do not open or disassemble the camera. There are

7. Do not drop the camera or subject it to strong
* Note: Many video monitors produce strong

Base

Power

Connector

BNC

Connector

strong magnetic fields, or strong electrical signals.*
no user-serviceable parts inside.
vibrations.
electromagnetic fields close to the display CRT,

especially when the monitor is turned on or during de­Gaussing, which occurs automatically with many
monitors when the monitor is turned on.

311/16” (94mm)

35/32”

(80mm)

Installation:

1. Run a 12VDC power supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted.

2. Loosen the set screws with the included hex wrench
and remove the case from the base.

NOTE - The camera ball is NOT attached to the case
or the base. It sits loose inside the case. Therefore, be
very careful when removing the case from the base to
not drop the camera ball.

3. Mount the base to the wall using the four included
mounting screws. If the wall is made of dry wall, brick,
or similar material, it may be necessary to use the
included plastic screw anchors.

4. Run the camera's BNC and power connectors through
the camera base, and connect to the video and power
wires that were run through the wall.

5. Put the case over the camera ball onto the base, being
careful to not drop the camera ball.

6. Holding the case loosely on the base, turn the camera
ball to the desired direction.

7. Once the camera ball is in the desired direction, tighten
the set screws with the included hex wrench. However,
do not tighten them too tightly. Tighten just enough so
that the case does not move, and the camera ball does
not rotate.

8. Do a final test of the video camera and the monitor.