SECO-LARM USA EV-1006-N4SQ User Manual

ENFORCER CCD IR Day/Night Camera Manual

TROUBLE SHOOTING

The screen is blank

The screen image is dim

The screen image has poor contrast

The screen image flickers
The screen image is distorted
The camera case is hot
IR LEDs do not turn on

IMPORTANT

Users and installers of this product are responsible for ensuring this product complies with all national, state, and local
laws and statutes related to monitoring and recording audio and video signals.
responsible for the use of this product in violation of any current laws or statutes.

WARNING

Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field-serviceable components inside.

Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the monitor is connected properly.

Clean the lens (using a soft, clean cloth).
Check that the light source is adequate.

Adjust the monitor’s contrast knob.
Change the position of the camera.

Change the position of the camera.
Change the position of the camera.
Check that the correct power supply is in use.
Check that the correct power supply is in use.

SECO-LARM

will not be held

MANUAL

1/3" Sony CCD Color IR Day/Night Cameras

o

4.3mm Lens, 78

EV-1006-N4BQ -- Black Case
EV-1006-N4SQ -- Silver Case

EV-1006-N4WQ -- White Case

Viewing Angle, up to 60’ IR Range

®

FCC COMPLIANCE STATEMENT

Information to the user: This equipment has been tested and found to comply with the limits for a class a digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.

WARRANTY

ENFORCER IR Cameras are warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original customer. Our obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2008 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
or in part, without the written permission of SECO-LARM.

SECO-LARM® U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Tel: [phone] Fax: [phone]

Website: www.seco-larm.com
E-mail: sales

@

seco-larm.com

IMU_EV-1006-N4xQ.PMD

®

PITMW2

Weatherproof

ENFORCER CCD IR Day/Night Camera Manual ENFORCER CCD IR Day/Night Camera Manual

Specifications

Type
Chip
Resolution
Pickup elements
Scanning system
Sync
Video output
Lens
Minimum illumination
Gamma correction
S/N ratio
Shutter control
Backlight compensation
Automatic gain control (AGC)
Enclosure
# of infrared LEDs
Max. LED range
Power source
Power consumption
Operating temperature
Dimensions
Weight

Dimensions:

215/16” (74mm)

EV-1006-N4BQ/SQ/WQ

Color camera

1/3” CCD, Sony

420 TV lines

510 x 492 pixels (NTSC / EIA)

2:1 interlace

Internal

1Vp-p composite output, 75 ohms

4.3mm, F2.0 fixed

0.4 lux (LED off), 0.0 lux (LED on)

0.45

>50dB (AGC off)

Auto Electronic Shutter (AES) 1/60~1/100,000 sec. (NTSC)

On

Auto

IP66 weatherproof

18

Up to 60 ft. (18m)

12VDC±10%

100mA (IR off), 280mA (IR on)

14°~122° F (-10°~50° C)

1

6

/4”(L) x 215/16”(D) (158 x 74 mm)

13.6 oz. (386g)

1

4

6 /

” (158mm)

” (74mm)

16

/

15

2

3 /

3

4

ENFORCER

” (95mm)

®

1

16

2 /

” (52mm)

A. Camera
B. Mounting base
C. 12” cord
D. DC jack*
E. BNC connector (female)
F. Adjustment collar
G. Locking screw

D*

B

F

Parts List

1 x IR camera with integrated

mounting bracket
3 x Mounting screws
3 x Screw anchors
1 x Manual

E

*Important:

Do not cut DC jack.
Use SECO-LARM’s

optional EVA-F5521-3

Pigtail Connector for
easy installation and

serviceability.

C

G

A

BEFORE STARTING

1. Please read this manual carefully and keep it for
future reference.

2. Use the camera within given temperature and
electricity limits.

3. Do not aim the LED light directly at the eyes when
the LEDs are on.

4. Do not point the camera at the sun. Heat could

” (62mm)

16

/

7

2

damage the camera, even when not in use.

5. Do not mount the camera in areas exposed to

6. Do not open or disassemble the camera. There
are no user-serviceable parts inside.

7. Do not drop the camera or subject it to strong
vibrations.

* Note: Many video monitors produce strong

electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during
de-Gaussing, which occurs automatically with
many monitors when the monitor is turned on.

radiation, strong magnetic fields, or strong electrical
signals.*

Optional Accessories:

EVT-PB1Q

O

Passive Video Baluns.

O

Up to 2,000 ft. range
over CAT5e UTP cables.

EVP-1SD4P9UL

O

CCTV power supplies.

O

4, 9, 16 outputs available.

VG-1C12AQ

O

Ground loop isolator.

ST-UV12-S0.5Q

O

Full line of plug-in adapters.

INSTALLATION

1. Run a 12VDC power supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted (if necessary).

2. Using the mounting screws and screw anchors,
attach the mounting base to the wall or ceiling where
the camera is to be mounted.

3. Connect the camera to the 12VDC power supply.

4. Connect the camera’s female BNC connector to the
male BNC connector of the video cable.

5. Attach the camera to the mounting base by twisting
the adjustment collar and securing it to the plate.

6. Adjust the camera so the picture on the monitor
clearly displays the image from the camera.

7. Using the adjustment collar and locking screw,

secure the camera in place.