SECO-LARM USA 762FP-ISS User Manual

Congratulations! Your vehicle is now protected by the SLI 762FP-ISS.
This Touchkey Immobilizer is designed to be used with almost any
vehicle.

The Touchkey Immobilizer combines high security with the
convenience of completely automatic arming.

To disarm and operate the vehicle, insert the Touchkey, remove it, and
start the engine. No other buttons to push, no codes to remember.
When the destination is reached, turn the engine OFF. 30 seconds
later, the engine is automatically and completely disabled.

When the Touchkey is inserted into the receptacle, the Immobilizer
reads the key’s code. If the Touchkey was properly coded to the
system, the Immobilizer disarms, allowing the engine to start as
normal.

However, the engine won’t start if someone tries to start it without the
Touchkey. Only Touchkeys properly learned by the system can start
your engine!

Included with the SLI 762FP-ISS is a small card with a secret PIN.
This 3-digit number is required to enter the valet mode, do emergency
disarm, or add new Touchkeys.

DO NOT LOSE THE CARD. KEEP IT IN A SAFE PLACE.

For information on valet, emergency disarm, or code learning new
Touchkeys, see page 2.

The LED indicates the following:

1. Armed – While unit is armed, the LED flashes.

2. Arming – While unit is arming, the LED flashes rapidly.

3. Disarmed – While the unit is disarmed, the LED is OFF.

4. Triggered – If you try to start the engine without the Touchkey, the

LED will show steady ON.

5. Code learning – The LED will show steady ON to indicate a new

Touchkey has been successfully learned.

6. Valid code entered – If a valid PIN number or programming code is

entered, the LED will flash rapidly for three seconds.

7. Valet/override – When the Immobilizer is in the valet/override

mode, the LED will flash 11 times, then flash slowly when the
ignition is turned OFF. The LED will turn OFF when the ignition is
turned ON.

1. Normal disarm – Insert the Touchkey into the receptacle and

remove it. Start the engine within 30 seconds. If the engine is not
started within 30 seconds, the Immobilizer will automatically rearm.

2. Emergency disarm – If the Touchkeys are lost, use the secret PIN

to put the unit into valet/override mode (see page 2).

1. Arming procedure:
a. Turn the ignition switch OFF.
b. 30 seconds later (unless you turn the switch ON again), the

unit arms, and the LED flashes slowly.

2. Re-starting the engine:
a. Within 30 seconds of turning the ignition OFF – Start the

car normally.

b. 30 seconds or more after turning the ignition OFF – Go

through the disarming procedure again (see above).

PERSONAL ID NUMBER (PIN)

LED INDICATOR
HOW IT WORKS

INTRODUCTION

DISARMING THE SYSTEM

ARMING THE IMMOBILIZER

SECO-LARM

®

OWNERS MANUAL

INTERNAL
SECURITY

TOUCHKEY IMMOBILIZER
SLI® 762FP-ISS

Tel: [phone] (Domestic U.S. & Canada) Email: [e-mail] Website: www.seco-larm.com
16842 Millikan Avenue, Irvine CA 92606 Tel: [phone] (California and International) Fax: [phone] mi-SLI 762FP-ISS OWNERS.docx

SECO-LARM

®

1. VALET MODE – The Immobilizer automatically arms 30 seconds

after the engine is turned OFF. However there may be certain
times (for repair or if the Touchkeys are lost, for instance) that
arming the Immobilizer is not desired. Note: When in the

valet/override mode, the LED flashes while the ignition is turned
OFF to help deter thieves. When the ignition is turned ON, the LED
will turn OFF.

2. EMERGENCY DISARM – If the Touchkey is lost, the engine will not

start, even with the proper car keys. In this case, the Immobilizer
must be put into the valet/override mode using the emergency
disarm procedure.

3. EMERGENCY DISARM/VALET MODE

Note: Immobilizer must be armed before you can enter your PIN.

a. Know the secret PIN. For the following example, assume the

PIN is 503. Note: Count 10 flashes for the number “0”.

b. While the LED is flashing (because the Immobilizer is armed),

turn the ignition ON. The LED will show steady ON.

c. Turn the ignition OFF and the LED will start flashing. Count

the flashes. After the 5th flash, turn the ignition ON. The LED
will show steady ON again. (This is your PIN’s first digit—5.)

d. Turn the ignition OFF and count the flashes. After the 10th

flash, turn the ignition ON. The LED will show steady ON
again. (2nd digit, 0)

e. Turn the ignition OFF and count the flashes. After the 3rd

flash, turn the ignition ON. The LED will show steady ON
again. (3rd digit, 3)

f. At this point, the LED will show steady ON for 10 seconds then

OFF to indicate the Immobilizer is in the valet/override mode.

4. EXITING THE VALET/OVERRIDE MODE – Insert a valid Touchkey

into the receptacle. EXIT VALET/OVERRIDE MODE AS SOON
AS POSSIBLE TO PREVENT THEFT OF YOUR VEHICLE.

1. If power is ever removed from the Immobilizer and then restored, it

will return to the state prior to removing power (If armed when
power was removed, it returns armed. If disarmed when power is
removed, it remains disarmed.)

2. While driving (when the ignition switch is ON), if the main power is

cut to the Immobilizer, the car will continue to function normally.

1. NUMBER OF TOUCHKEYS – The Immobilizer comes factory

coded to the two Touchkeys included in the package. The unit can
learn the codes of up to 4 Touchkeys.

Note – This procedure deletes the existing Touchkey Codes.
Therefore, you must do this procedure for both existing and new
Touchkeys at the same time.

2. CODE LEARNING PROCEDURE

Note: Immobilizer must be armed before you can enter your PIN.

a. Add the digits ―55‖ to the end of your secret 3-digit PIN. (For

example, if the PIN is 503, the 5-digit code learning PIN
is 50355).

b. While the LED is flashing (indicating the Immobilizer is armed),

turn the ignition ON. The LED will turn steady ON.

c. Turn the ignition OFF and count the flashes. After the 5

th

flash, turn the ignition ON. The LED will be steady ON again.
(This is your PIN’s first digit—5.)

d. Turn the ignition OFF and count the flashes. After the 10th

flash, turn the ignition ON. The LED will be steady ON again.
Note: “0”=10 flashes (2nd digit, 0)

e. Turn the ignition OFF and count the flashes. After the 3rd

flash, turn the ignition ON. The LED will flash rapidly.
(3rd digit, 3)

f. Turn the ignition OFF and count the flashes. After the 5th

flash, turn the ignition ON. The LED will be OFF. (4th digit, 5)

g. Turn the ignition OFF and count the flashes. After the 5th

flash, turn the ignition ON. The LED will flash rapidly.
(5th digit, 5)

h. Leave the ignition key ON. Once the LED stops flashing,

insert a Touchkey into the receptacle within 10 seconds. The
LED will turn steady ON to show the Touchkey was
successfully learned. (Repeat for all touch keys.)

3. EXIT THE CODE LEARNING PROCEDURE – There are three

ways to do this:

a. Turn the ignition switch OFF.
b. Wait more than 10 seconds to insert a new Touchkey.
c. If memory is full (you try to learn a 5th Touchkey), the unit will

go into valet/override mode.

Note: If new codes are programmed, all of the existing Touchkeys
must also be re-programmed.

4. MISTAKES – If the PIN is incorrectly keyed in, simply start over

from the first digit. Ignore any digits that have already been
keyed in.

CODE LEARNING NEW TOUCHKEYS

VALET MODE and EMERGENCY DISARM

POWER DOWN AND POWER UP

TOUCHKEY IMMOBILIZER SLI® 762FP-ISS

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) ye ar from the date of sale to the original
consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if
for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any
special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For
this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2009 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

PITTW3