Seco-Larm SS-072Q User Manual

ENF ORCER

SS-072Q

®

Tamper Switch

Type: S
49J5

UL Listed for Supplementary Protection

FEATURES:

!

Used in alarm systems with normally-closed circuits.

!

Silver-plated contact ensures reliability and long-term operation.

!

Small size makes it easy to hide and install.

SPECIFICATIONS:

!

Plunger Pushed in: Contact closed

!

Plunger Released: Contact Open

!

Contact Rating: 0.5A at 50 VDC

!

Enclosure: High-impact Plastic Resin

! Size: 2-
! Weight: 18 gm

INSTALLATION INSTRUCTIONS:

1. Decide the appropriate position for the SS-072Q. (Note that the switch must be positioned so that it will be depressed at least

1/4” [6mm] to activated).

2. Drill the three holes necessary for the SS-072Q to be mounted firmly in place. The diameter of the hole is 1/8” (3mm). Screws
should be selected according to your own particular preference and need.

3. Connect the wires to the switch terminals, using series circuitry, see illustration on Fig.1.

3

/4” x 1-1/16” x 5/8” (70 x 28 x 16mm)

Fig.1- Used inside cabinet or drawer when
cabinet or drawer is pulled open.

1/4”(6mm)

Inside of
alarm case

Important Note: When mounting the tamper switch, keep in
mind that the switch must be depressed at least 1/4” (6mm)
distance in order to activate the switch.

Minimum activation distance

Drill three holes, each
hole 1/8” (3mm) and insert screws.

Connect the wires to switch terminals using series circuitry.

To alarm system

Note: Products with model number that ends with "Q" or have a green “Q” sticker represents RoHS compliant products.

Case body

Wall

Fig.2- Case against wall.
Use 2 SS-072Q to protect against the forced
removal of the case from the wall and the forced
removal of the case’s cover or lid.

Fig.3- Used inside box when top is opened
upward or lifted off.

To alarm
system

Case cover / lid

Hole must be made
for the tamper
switch to fit through

Case cover / lid

To alarm
system

The SECO-LARM® policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is not responsible for misprints.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale

to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty
installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable
for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

SECO-LARMSECO-LARM

SECO-LARM

SECO-LARMSECO-LARM

®

U.S.A., Inc., U.S.A., Inc.,

U.S.A., Inc., 16842 Millikan Avenue, Irvine, CA 92606

U.S.A., Inc., U.S.A., Inc.,

Tel: [phone] Fax: [phone]

Website: www.seco-larm.com

@

E-mail: sales

Copyright 2012 SECO-LARM U.S.A., Inc. All rights reserved.

seco-larm.com

MuSS-072Q_1208.pmd

Order Part #763-041-2%

PITSW1