Page 1
®
Open Bar works with an external electric strike or maglock to
provide egress from a protected area. It can work in stand
Features:
•
•
s unlocked (selectable,
SD-961A-36SLQ
Illuminated Push-to-Open Bar
Manual
The ENFORCER Illuminated Push-to-
-alone mode or as part of an access
control system, but also can be locked open by key. Buzzer, output timing, and LED function and
colors are also customizable.
Provides convenient on-door egress
• LED makes it easy to see the status
• Can be stand-alone or connected to an
access control system
• Two built-in non-latching (momentary), dual-
contact outputs (NO/NC/COM) rated at
≤5A@230VAC, adjustable 0.5~60 sec
• Dogging – standard dogging with hex key
• For 36" doors – actual length: 337/16" (85cm)
Can be cut to fit smaller doors, minimum
235/8" (60cm)
• Large LED shows red in standby and green
when triggered, but is programmable
red/green/blue by an access control panel
• Blinking LED and buzzer programmable for
relock warning
• Built-in buzzer indicate
up to 92dB)
Page 2
ENFORCER Illuminated Push-to-Open Bar
1x Illuminated push bar
5x Machine screws
1x Dogging key
1x Keyhole cover
2x Self-stick wiring
1x Manual
Overview:
Specifications:
Parts List:
Installation:
*Dogging key
shown in use
(normally removed)
Base end
Spring loaded push
Push bar end
Punchout for
≥9/16"
Specifications Parts List:
Operating voltage 12~24 VDC
Power consumption 180mA@12VDC, 140mA@24VDC (max.)
Contact load ≤5A@230VAC
Outputs NO/NC/COM x2
Trigger duration 0.5~60 seconds (adjustable) or dogged open
Buzzer Up to 92dB (adjustable)
LED
Indicator
Door width 36" (91.4cm), minimum 235/8" (60cm)
Operating temperature 32°~150° F (0°~70° C)
Dimensions 337/16"x23/8"x23/8" (850x61x61 mm)
Weight 4-lb 10-oz (2.1kg)
Colors Stand-alone red/green, Controlled red/green/blue
Size 81/4"x1" (210x25 mm)
Cutaway View
cap (x2)
LED Indicator Push bar
anchors
Dogging key*
23/8"
(61mm)
Exposed wiring (x2)
PCB
337/16" (850mm)
81/4" (210mm)
bar bracket (x2)
1" (25mm)
cap (x2)
23/8"
(61mm)
Please read the manual carefully before beginning installation.
1. Hold the push bar unit on the door at the desired
height, ensuring that there is sufficient space on
both ends as noted below. With a pencil, mark
2. Remove the two screws from each of the push
bar end caps and remove the end caps.
P US H TO E X IT
the lower edge of the base and the edge of the
base end cap on the latch side of the door.
NOTES:
• Leave at least 9/16" (1.5cm)
space between the door edges
and both ends of the base.
• Level with a bubble level.
• The height of the push bar from
the floor may be subject to
local regulations.
(1.5cm)
If you need to cut the push bar to fit a door narrower
than 36" (91.4cm), skip to step 4.
3. For doors at least 36" (91.4cm) wide, mount the
bar to the door. Using the lines drawn in step 1,
hold the base in place and mark 4 mounting
screw holes (and the wiring hole if wiring runs
through a hollow door using an electric transfer
hinge). Drill holes, making sure not to go all the
way through the door and mount on the door.
• Usually, the bar is centered but for wider
doors it can be closer to the latch side.
2 SECO-LARM U.S.A., Inc.
Page 3
ENFORCER Illuminated Push-to-Open Bar
Installation (Continued):
Wiring
punch outs
Base end cap
Bar end cap
Included with the push bar is a
dogging
key. To lock the push bar closed (to allow two
-
way, uncontrolled
cover, push the bar in all the way, and turn the bolt with the
Lock
ing the Bar
Open
:
NOTE: The wiring connection is normally on the
hinged side of the door.
4. Remove the mounting bracket from one end of
the push bar.
XIT
TO
E
USH
P
5. Taking care not to damage the LED wiring
harness, slide the push bar in the direction of
the removed endplate until it is free of the
opposite push bar bracket, lift the free end,
and slide in the other direction until it is free.
6. Unplug the LED cable from the PCB.
If you do not need to cut the push bar, skip to step 8.
7. To cut the push bar to fit a narrow door:
a. Unscrew and remove both base end caps.
b. Remove the screws and slide the two push
bar brackets off the base.
d. Measure the door width and subtract from
36" (91.4cm). Divide the result in half and
carefully mark the base and push bar to cut
an equal amount from each end of both.
Centerline
NOTES:
• The minimum cut length is 235/8" (60cm).
• Both push bar and base must be the same
length and the cuts must be at a 90° angle.
e. Replace the circuit board, push bar brackets,
and base end caps (reversing steps 7a~7d,).
Mount the base to the door as in step 3.
8. For exposed wiring or an armored cable, punch
out the scored wiring hole on the side of the
base end cap and the scored piece from the
corresponding push bar end cap.
9. Run the wires through the base cap hole and
connect to the terminals (see Sample
Installations and Wiring Diagrams, pg. 4). If
using an armored cable, attach the cable.
Concealed wiring
hole (hollow door)
Exposed wiring or
armored cable hole
c. Remove the screws and slide the circuit
board off the base.
10. Plug the LED wiring harness back in to the PCB,
replace the push bar, and reattach the end caps,
reversing steps 4~6.
d.
access to the protected area), remove the keyhole
dogging key. To release the bar, turn the bolt to its original position.
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Illuminated Push-to-Open Bar
Sample
Applications
and Wiring Diagrams:
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800 Email: sales@seco
-
larm.com
PITSW2
NOTICE
:
The SECO
-
LARM policy is one of continual development and improvement. For that
reason, SECO
-
LARM
rademarks
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship while
used in normal
RM’s obligation is limited to the repair or
This Warranty is void if
neglect, repair or alteration,
LARM determines that such equipment
obligation of
’s
LARM be liable for any special, collateral, incidental, or consequential personal or property
IMPORTANT:
It i
s the responsibility of the installer and/or end
-
user customer to ensure the
Illuminated Push
-to-
Open Bar
uitability for doors accessed by
WARNING:
The push bar is not weatherproof. Do not mount on exterior surfaces or where exposed to rain
.
IMPORTANT:
The height at
which the push bar is mounted
may be subject to local regulations.
Switch up for
Output duration
Buzzer v
olume
–
+
–
LED/Buzzer warning
or
Switch down for
or
–
+
Auxiliary
–
Buzzer output
Blue output
Auxiliary
Green out
put
Red output
Input (NO/NC
COM
To electric lock NO/NC
Buzzer and LED colors are
*
The LED can be set to blink while the buzzer sounds
OFF
ON (default)
California Proposition 65 Warning
: These products may contain chemicals which are known to the State of California to
stand-alone mode
Stand-Alone Installation (Factory Default)
mode jumper*
Door Lock
output†
12~24VDC
Power Supply
control
(default = min.)
controlled mode
(0.5~60s,
default = 60s)
intermittently during the last 6 seconds of the output
as a warning that the door is about to relock.
Security System Installation
output†
12~24VDC
Power supply
Buzzer volume, output
duration, LED settings are
controlled by the alarm
control system.
all negative triggers.
†
Light, strobe, siren, alarm, etc.
cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Control panel
meets all local regulations regarding the use of push bars for access security, including: s
disabled persons and suitability for fire doors (the push bar is not fire-rated).
service for one (1) year from the date of sale to the original customer. SECO-LA
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse,
improper or abnormal usage, or faulty installation, or if for any other reason SECOis not operating properly as a result of causes other than defects in material and workmanship. The sole
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM
option. In no event shall SECOdamage of any kind to the purchaser or anyone else.
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All t
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2021 SECO-LARM U.S.A., Inc. All
rights reserved.
SECO-LARM
®
U.S.A., Inc.
MI_SD-961A-36SLQ_210329.docx
4 SECO-LARM U.S.A., Inc.
Loading...