Seco-Larm SD-927PWCQ User Manual

ENFORCER

No Touch

Request-To-Exit Sensor

Manual

SD-927PKC-NEQ (English)
SD-927PKC-NSQ (Español)
SD-927PKC-NFQ (Francais)

The ENFORCER No Touch Request-To-Exit Sensor uses IR technology to request egress from a protected
area or activate a device with the simple wave of a hand. Since it is No Touch, this sensor is ideal for use
in hospitals, clinics, labs, cleanrooms (to reduce the risk of contamination), schools, factories, or offices.

,

SD-927PWCQ

(English / Español / Francais)

,

Features:

• Range up to 4” (10cm). Range for
SD-927PWCQ is up to 2” (5cm).

• Stainless steel or white plastic
single-gang plate.

• 3A relay, triggers minimum 0.5 sec or as
long as hand is near the sensor.

Note: Products with model number that ends with "Q" or which have a round green “Q” sticker represent RoHS compliant products.

• LED illuminated sensor area for
easy identification.

• Quick connect screwless terminal block.

• Selectable LED colors (turns from red

to green or green to red) to show
sensor activated.

NO TOUCH REQUEST-TO-EXIT SENSOR Installation Manual

Installation:

1. Run four wires through the wall to a single-gang
back-box.

2. Connect the four wires from the back-box to the quick
connect screwless terminal according to Fig. 1.

3. Screw the plate into the back-box, taking care not to crimp
the wires.

4. Remove clear protective film from the sensor before use.

Adjusting the LED Color

1. The LED color factory default setting is red (standby) and
green (triggered).

2. To reverse the LED color visual indicator to green (standby)
and red (triggered), remove the jumper located at the right
side of the terminal block as shown in Fig. 1.

Pasting the Decals (For SD-927PWCQ model only)

1. The SD-927PWCQ model includes “NO T OUCH” and “EXIT”
decals in English, French and Spanish.

2. Select the appropriate decals according to your requirements.

3. Remove the back sheet of the decal and then set it on the
desired location. Use the thin lines on the left and right sides of
the text on the decals for alignment, see Fig. 2.

4. After the decal has been placed and set in the desired location,
scratch the front of the decal to transfer the text onto the
faceplate.

Note: The decal needs at least 24 hrs. to fully dry & bond with the

surface. Do not touch or scratch until the decal is fully dry.

Specifications:

Power
Current drain (max)
Relay type
Response time

LEDs
Output time

Range
Temperature range

Weight

Standby

Triggered

SD-927PKC-NEQ
SD-927PKC-NFQ
SD-927PKC-NSQ

50mA @ 12VDC

Form-C dry contact, 3A@24VDC

0.5 sec. or as long as sensor is triggered
4" (10cm)

-4O ~ 131OF (-20O ~ 55OC)

3oz (85g)

SD-927PWCQ

12VDC

10mS

Red*

Green*

2" (5cm)

2.5oz (70g)

*Reversible via jumper

Fig. 1 –Connections (under

back cover)

Power Input Relay Output (3A max)

( )

NC COM NO

( )

Jumper

( for LED color adjustment )

Fig. 2 – Decal Alignment

NO TOUCH

EXIT

11/8”

(29mm)

21/8”

(55mm)

2

SECO-LARM U.S.A., Inc.

NO TOUCH REQUEST-TO-EXIT SENSOR Installation Manual

Example Installations:

1. Installation with Electromagnetic Lock (Fail-Safe)

EAP-5D1Q
Access Control
Power Supply

ENFORCER Series

12VDC

Power input

( ) (+)

(+)

(-)

2. Installation with Electric Doorstrike (Fail-Secure)

EAP-5D1Q
Access Control
Power Supply

Relay output

NC COM NO

Electromagnetic Lock

ENFORCER Series
Electric Strike

12VDC

Power input

( ) (+)

3. Installation with Electromagnetic Lock and Keypad

EAP-5D1Q

Access Control Power Supply

(+)

(-)

SK-1011-SQ (Digital Keypad)

EGRESS

COM

NO

NC

Tamper

O/P (N.C.)

Relay output

NC COM NO

12VDC

Power input

(-)

( )

ENFORCER Series
Electromagnetic Lock

Relay output

NC COM NO

3

NO TOUCH REQUEST-TO-EXIT SENSOR Installation Manual

Care and Cleaning for the SD-927P Series No-Touch:

The SD-927P Series is designed for inside use to match most interiors. The sensor and included
decals (SD-927PWCQ only) require special care to ensure reliability and a long operating life.

1. Use a soft, clean cloth for cleaning. Rough materials may scratch the decals of the SD-927PWCQ.

2. Be careful not to spray liquids directly on the unit.

3. When cleaning, spray the cleaning solution onto the cleaning cloth instead of the unit.

4. Be sure to wipe off any excess liquid from the sensor. Wet spots or areas may affect the
sensor’s performance.

5. Repeated exposure to strong cleaning chemicals may damage the decals included with the
SD-927PWCQ. Use the mildest type of cleaner available.

WARNING: Incorrect mounting which leads to exposure to rain or moisture inside the enclosure
could cause a dangerous electric shock, damage the device, and void the warranty.

WARRANTY This SECO-LARM product is warranted against defects in material and
workmanship while used in normal service for a period of one (1) year from the date of sale to the
original consumer customer.

SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is
returned, transportation prepaid, to SECO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical
misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation,
or if for any other reason SECO-LARM determines that such equipment is not operating properly
as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to
replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for
any special, collateral, incidental, or consequential personal or property damages of any kind to
the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of
publication. However, the SECO-LARM policy is one of continual development and improvement.
For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be
reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

®

SECO-LARM U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]

MiSD927PKC-NxQ_122110.pmd

Website: www.seco-larm.com
E-mail: sales

@

seco-larm.com

PITSW3

4