Seco-Larm NS-104UT-MAQ, NS-508UT-GAQ Installation Manual

Page 1
®
Features:
Unmanaged PoE Switches
Manual
NS-508UT-GAQ shown
Model Ethernet Ports Bandwidth VLAN Power
NS-104UT-MAQ 10/100Base-TX 4 Downlink, 2 uplink 1.2Gbps Yes 60W Adapter NS-508UT-GAQ 10/100/1000Base-TX 8 Downlink, 2 uplink 20Gbps No 120W Built-in
Provides both Ethernet data and power to multiple PoE devices including IP cameras, IP access, IP speakers/intercoms, VOIP, etc.
Specially designed for video transmission with fast packet forwarding capability for clear images and smooth transmission
Easy plug-and-play installation
Supports 10,100BaseT (NS-508UT-GAQ supports up to 1000BaseT Gigabit)
Conforms to IEEE 802.3, IEEE 802.3u, IEEE 802.3af, IEEE 802.3at (NS-508UT-GAQ also conforms to IEEE 802.3ab)
IEEE 802.3x Flow control
Page 2
ENFORCER Unmanaged PoE Switches
NS-104UT
-
MAQ
Overview:
ENFORCER
Unmanaged
PoE Switches provide Ethernet and power to PoE devices
such as IP
1x PoE Switch
1x
AC Power cord
1x Power adapter*
1x
Manual
Model
NS-
104UT
-
MAQ NS-508UT-GAQ
Operating voltage
48~57 VDC*
100~240 VAC
Power consumption
<5W <15W
Ports 4 Downl
i
nk, 2 uplink
8 Downlin
k, 2 uplink
Ethernet speed
10/100Mbps (uplink, 100Mbps)
10/100/1000Mbps (uplink, 1000Mbps)
IEEE 802.3, IEEE
802.3u,
Transmission distance
328ft (100m)
328f
t (100m)
PoE Capacity
55W 120W
Switching capacity
1.2G
bps 20G
bps
10Mbps
14,880pps
100Mbps
148,800pps
1000Mbps
N/A 1,488,000pps
MAC Address table
1K 4k
LED Indicators
Connection/transmission and PoE for each po
rt
, power
Operating humidity
0~85% Non
-
condensing
0~85% Non
-
condensing
Operating t
emperature
-40°~158
° F (-40°~70
° C) -40°~
158
° F (-40°~70
° C)
Dimensions
4"x7/8"
x215/16" (
102x22x75 mm) 77/8"x23/4"
x45/8" (
200x44x118 mm)
Weight
6.8-oz (
194g) 1-
lb
12.4-oz (
806g)
Specifications:
Introduc
tion:
215/16"
(75mm)
4"
/8"
PoE
Link/Active
*Flashing green when data is being transmitted
Power LED
Uplink ports
Power input
VLAN Switch
Downlink
ports
cameras, IP access control, IP speakers/intercoms, IP telephony, etc. Fast packet forwarding capability and extra backplane bandwidth ensure clear images at fast transmission speeds for video, making them well-suited for HD CCTV installations.
Parts List:
*NS-104UT-MAQ only
Ethernet standard
IEEE 802.3, IEEE 802.3u,
IEEE 802.3af, IEEE 802.3at
†‡
Transfer rate
*Power adapter included
Distance depends on Ethernet cables used. Cat5e/6 recommended.
656ft (200m) at 10Mbps with VLAN switch ON
(102mm)
4-Port PoE Switch
LED
LED*
PoE
1 2
3
4
Link/Act
IEEE 802.3af, IEEE 802.3at,
IEEE 802.3x, IEEE 802.3ab
6
Uplink
5
On / Off
Power
DC In
7
(22mm)
2 SECO-LARM U.S.A., Inc.
Page 3
ENFORCER Unmanaged PoE Switches
Sample Installation
:
NS-508UT
-
GAQ Overview:
77/8"
(200
mm)
45/8"
Power LED
8 Downlink
2 Uplink
100~240
13/4"
PoE
Link/Active
*Flashing green when data is being transmitted
Sample
CCTV
Application:
1. Determine the best location for the switch. Note that the uplink cable (as well as the PoE
PoE Cameras or other PoE devices
HD Monitor
DVR
Power adapter
PoE Switch
LED
VAC Power
LED*
input (on
back panel)
(118mm)
2 4
ports
8-Port Gigabit PoE Switch
/
13
/
Power
PoE Link/Act
6 8
/
Uplink
5 7
/
(44mm)
G2G1
ports
device cable, except for the NS-104UT-MAQ with the VLAN function switch turned ON) cannot exceed 328ft (100m).
2. If installing the NS-104UT-MAQ, make sure that the VLAN function switch is set correctly.
3. Turn off power to both the display device and the PoE device before proceeding. Installation
under power will damage the transmission equipment.
4. Connect the PoE device(s) to a downlink port on the switch using a Cat5e/6 cable conforming
to either the EIA/TIA 568A or 568B standard.
5. Connect the DVR or computer to the uplink port on the switch using a Cat5e/6 cable
conforming to either the EIA/TIA568A or 568B standard.
6. Connect the power to the switch and ensure that the power LED and the POE led on any
connected port is on.
7. Turn on the display device and ensure that the system is functioning properly.
(NS-104UT-MAQ shown)
PoE
1 2
4-Port PoE Switch
3
4
Link/Act
Power
6
Uplink
5
On / Off
DC In
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Unmanaged PoE Switches
Troubleshooting:
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
Phone: (949) 261
-
2999 | (800) 662
-
0800 Email:
sales@seco
-
larm.com
PICSN7
MI_NS-x0xUT-xAQ_200611.docx
NOTICE
:
The S
ECO-LARM policy is one of continual development and improvement. For that reason, SECO
-
LARM reserves
rademarks are the
Inc. All rights
WARRANTY:
This SECO
-
LARM product is warranted against
defects in material and workmanship while
used in normal
LARM’s obligation is limited to the repair or
This Warranty is void if
oper
determines that such equipment is not
LARM
In no event
LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind
IMPORTANT
: Users and installers of this product are responsible for ensuring this produ
ct complies with all national, state,
will not be held
FCC COMPLIANCE
STATEMENT
E FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
THIS DEVICE MUST ACCEPT
or modifications not expressly approved by the party responsible for compliance could void the user’s
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device
permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements
Confirm that both input and output devices are turned on
Ensure that the Ethernet cable does not exceed 328ft (100m) or 656ft
(200m) for NS-104UT-MAQ with VLAN function switch turned ON PoE Device doesn't function correctly
Confirm that no PoE equipment power requirement exceeds 30W
Confirm that the Ethernet cable meets EIA/TIA 568A or 568B standard
and that both ends are the same standard (not a crossover cable)
Test that the Ethernet cable to ensure that it is operational
Test with another PoE device that is known to be operating correctly
and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM responsible for the use of this product in violation of any current laws or statutes.
THIS DEVICE COMPLIES WITH PART 15 OF TH CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice: The changes authority to operate the equipment.
is and void user’s authority to operate the device.
service for one (1) year from the date of sale to the original customer. SECO­replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, impr or abnormal usage, or faulty installation, or if for any other reason SECO-LARM operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO­and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. shall SECO­to the purchaser or anyone else.
the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All t property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A., reserved.
SECO-LARM
®
U.S.A., Inc.
4 SECO-LARM U.S.A., Inc.
Loading...