NE
-
SE01
-020Q
Manual
•
•
Passive Ethernet Extender over Coax
1 Channel Ethernet over coax
• 10/100 Mbps Full duplex
• Transmission distance:*
- Up to 650ft (200m)@10Mbps
- Up to 325ft (100m)@100Mbps
*Actual transmission range will vary depending on equipment used and cable grade.
Passive, no power required
• Built-in surge protection
• Fast and easy to install
• Sold as a set
ENFORCER Passive Ethernet Extender over Coax
Introduction:
ENFORCER
Passive Ethernet Extender over
Coax is
designed to extend the range of any
Specifications:
23/8”x11/8”x13/16
(60x29x20 mm)
Parts List:
2x Passive Ethernet
Extenders
Dimensions:
TCP/IP device beyond the 300ft (100m) limit of Ethernet. The unit does not filter out any
protocols, codes, or applications, ensuring compatibility with any IP camera and its
software.
Type Passive Ethernet Extender over Coax
Range*
10Mbps (RG59) Up to 650ft (200m)
100Mbps (RG59) Up to 325ft (100m)
Input connector RJ-45
Output connector BNC
Link cable
Ethernet speed
Standard
Operating temperature
IEEE802.3 10Base-T/100Base-T
RG59/U or better
10/100 Mbps
-4°~158° F (-20°~70° C)
Dimensions
*Actual transmission range will vary depending on equipment used and cable grade.
1x Manual
Note: Pigtail length is 5” (127mm)
5
/8” (16mm)
23/8” (60mm)
(Excluding pigtail)
11/8” (29mm)
13
/16” (20mm)
Note: Both Ethernet extender units are the same size.
2 SECO-LARM U.S.A., Inc.
ENFORCER Passive Ethernet Extender over Coax
Overview:
Installation:
Sample Application:
Passive Ethernet Extender
Coaxial cable
IP Camera
NVR
Passive Ethernet Extender
The passive Ethernet e
xtender units are bidirectional transceivers. It can operate as a transmitter and receiver
.
RJ45
BNC Connector
1. Determine the location where the units will be placed as well as how much cable will be
required.
2. Connect one unit to an IP camera or other TCP/IP output device using Cat5e/6 cable of
not more than 6.5ft (2m).
3. Connect one unit to a DVR, PC or other TCP/IP receiving device using Cat5e/6 cable
Cat5e/6 cable of not more than 6.5ft (2m).
Connect via the Ethernet port found on the front of the Passive Ethernet Extender.
4. Run a coax cable between the two Passive Ethernet Extenders and connect both ends.
5. Switch on the IP source (i.e. CCTV camera) and verify that the system is functioning
properly.
1
NE-SE01-020Q
Cat5e/6 cable
(not more than 6.5ft)
1
2
Actual transmission range will vary depending on equipment used and cable grade.
up to 650ft (200m)@10Mbps
NE-SE01-020Q
2
SECO-LARM U.S.A., Inc. 3
1
Cat5e/6 cable
(not more than 6.5ft)
ENFORCER Passive Ethernet Extender over Coax
NOTICE
:
However, the
LARM reserves the right to
Trademarks
aterial may not be reproduced or copied, in whole or
LIMITED
WARRANTY:
LARM product is warranted against defects in material and workmanship while
LARM’s obligation is limited to
This Warranty
to acts of God, physical or electrical misuse or abuse, neglect, repair or
LARM determines that such
The sole
LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at
al, incidental, or consequential
SECO
-
LARM
Troubleshooting:
•
Also Available from SECO
-
LARM:
Passive VGA Balun
Passive Video Baluns
HDMI to VGA Converter
HDMI Extender over Coax
CCTV Power Supplies
Ethernet over Coax w/ PoE
Make sure the Passive Ethernet Extender is connected
on both sides.
• Make sure the IP source and DVR or PC are powered.
• Test the coaxial cable between the units and make sure
IP Device does not function
correctly.
it is functional.
• Make sure that there are no problems with the IP
device, cables, or DVR by plugging the IP device
directly into the DVR or PC using the Cat5e/6 cables.
• Make sure that the cables do not exceed the maximum
distance (see pages 2 and 3 for more details).
MVE-SV010Q
EB-P501-01Q
MVE-AA11-01NQ
used in normal service for one (1) year from the date of sale to the original customer. SECOthe repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
is void if damage is caused by or attributed
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECOequipment is not operating properly as a result of causes other than defects in material and workmanship.
obligation of SECO
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collater
personal or property damage of any kind to the purchaser or anyone else.
SECO-LARM policy is one of continual development and improvement. For this reason, SECOchange specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
are the property of SECO-LARM USA Inc. or their respective owners.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This m
in part, without the written permission of SECO-LARM.
-
The information and specifications printed in this manual are current at the time of publication.
This SECO-
®
U.S.A., Inc.
EVP-1SA4P9UL
MVA-HV01Q
NE-AE01-030TQ
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
MiNE-SE01-020Q_150326.docx
4 SECO-LARM U.S.A., Inc.
PICFN1
Loading...