Seco-Larm MVS-AH41-01NQ User Manual

Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
MVS-AH41-01NQ
4x1 HDMI Switch
Manual
Switch will automatically select the active
input for added convenience
Use with IR over HDMI Kit (MVE-PN11-01Q)
to control the HDMI switch or HDMI sources via remote control even if they have been hidden away
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
ENFORCER 4x1 HDMI Switch
Output LED: Illuminated when the HDMI display is connected and ON.
Input LEDs (1~4): Illuminated when the corresponding HDMI source is connected and ON.
Power LED: Illuminated when power is connected to the splitter.
Source Selection Button: Press to cycle through the HDMI sources.
The ENFORCER 4x1 HDMI Switch allows easy switching between multiple HDMI sources. The switch works with most HDMI devices, delivering the very best in digital audio and video signals with HD resolutions of up to 1080p. An included remote control easily switches between HDMI sources. LED Indicators clearly display power status as well as the HDMI source being used. The switch will automatically select the active input for added convenience. The 4x1 HDMI Switches can be daisy chained up to four levels for even more inputs.
Specifications: Introduction:
Model
MVS-AH41-01NQ
Type
HDMI Switch
Input video signal
5.0Vp-p
Video formats supported
High-speed HDMI with 3D, HDCP 1.2
Audio formats supported
LPCM, Dolby-AC3, DTS 7.1, DSD
Output video
HDMI
Resolutions supported
1080p/1080i/720p/576p/576i/480p/480i
Video amplifier bandwidth
6.75Gbps
Video input connector
4x HDMI Type A 19-pin female
Maximum input cable length
24AWG: 50’ (15m); 26AWG: 30’ (10m); 28AWG: 16’ (5m)
Video output connector
1x HDMI Type A 19-pin female
Maximum output cable length
24AWG: 65’ (20m); 26AWG: 50’ (15m); 28AWG: 16’ (5m)
Operating voltage
5VDC
Power supply
1.2A@5VDC (2.1mm plug)
Current draw (single unit)
490mA@5VDC
Operating temperature
32°~158° F (0°~70° C)
Operating humidity
5~90% RH (no condensation)
Dimensions
3”x43/8”x
15/
16
” (76x111x24 mm)
Weight
7.8-oz (219g)
Overview:
Parts List:
Switch
Remote
1x HDMI Switch 1x Remote control 1x 5VDC Power supply 1x Manual
HDMI Inputs
3” (76mm)
43/8” (111mm)
15
/16”
(24mm)
HDMI
Output
Status LEDs
Input selection button
5VDC
IR Extender port
IR Adapter port
IR Sensor
Status LEDs and Source Selection:
2 SECO-LARM U.S.A., Inc.
ENFORCER 4x1 HDMI Switch
Optional IR Adapter
1. Connect the HDMI adapter and IR receiver from the IR over HDMI Kit (MVE-PN11-01Q – sold separately)
to the HDMI display.
2. Connect the HDMI cable from the adapter to the HDMI output of the HDMI Switch.
3. Connect the IR transmitter from the IR over HDMI Kit (MVE-PN11-01Q – sold separately) to the IR
adapter port of the HDMI Switch, making sure to point the IR transmitter at the HDMI sources.
4. When operating the HDMI source remotes, point the remotes at the IR receiver.
Sample Application:
Installation:
HDMI Switch
1. Determine the location of where the HDMI Switch will be installed in relation to the HDMI sources and
HDMI display.
2. Plug the HDMI sources into the HDMI connector inputs on the back of the switch.
3. Plug the HDMI display into the HDMI connector output on the side of the switch.
4. Plug the 5VDC adapter into the switch.
5. Turn the power on the HDMI sources and display device. Using the included remote or selection button
on the switch, change the HDMI sources going to the HDMI display.
4x1 HDMI Switch
HDMI Display
HDMI Sources
Power supply
Installation with Optional IR Extender for controlling a concealed HDMI Switch with remote (requires the MVE-PN11-01Q – sold separately)
Optional IR Extender
1. Connect the IR receiver from the IR over HDMI Kit (MVE-PN11-01Q – sold separately) to the IR extender
port of the HDMI Switch.
2. Place the HDMI Switch out of sight, but leave the IR receiver exposed.
3. When operating the HDMI Switch remote, point the remote at the IR receiver.
4x1 HDMI Switch
HDMI Display
HDMI Sources
Power supply
IR RX
HDMI Source Remote
IR TX
Installation with Optional IR Adapter for controlling concealed HDMI sources with remote (requires the MVE-PN11-01Q – sold separately)
HDMI Switch Remote
IR RX
HDMI
Adapter
Cable Legend:
HDMI Power IR
For maximum cable length, see Specifications.
For maximum cable length, see Specifications.
SECO-LARM U.S.A., Inc. 3
ENFORCER 4x1 HDMI Switch
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in
normal service for the one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
PICHN1
Tel: (949) 261-2999 | (800) 662-0800
Email: sales@seco-larm.com
MiMVS-AH41-01NQ_1404.docx
Troubleshooting:
HDMI Device does not function correctly.
Make sure the switch is powered. Make sure the source(s) and display are
powered.
Make sure that there are no problems with the
HDMI source, HDMI cables, or HDMI display by plugging a source directly into the display using the HDMI cables.
Make sure that the source(s) and display are
plugged in to the correct connectors.
Make sure the HDMI source(s) are compatible
with the HDMI display.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Also Available from SECO-LARM®:
IR over HDMI Kit
MVE-PN11-01Q
Transmits IR signals from remotes
over HDMI cable
Plug and play operation – comes
as a complete set
High-Speed HDMI Cables
MC-1102-18NQ
1.5ft (0.5m), 28AWG
MC-1102-03FQ
3ft (1m), 28AWG
MC-1102-06FQ
6m (1.83m), 28AWG
MC-1102-10FQ
10ft (3m), 28AWG
MC-1102-16FQ
16ft (5m), 28AWG
MC-1102-20FQ
20ft (6m), 26AWG
MC-1102-25FQ
25ft (7.6m), 26AWG
MC-1102-30FQ
30ft (9m), 26AWG
MC-1102-50FQ
50ft (15m), 26AWG
Supports 3D videoSupports 4K
resolution
Supports EthernetLifetime warranty
4 SECO-LARM U.S.A., Inc.
Loading...