Seco-Larm MVE-PB020Q, MVE-PB010Q User Manual
ENFORCER Composite Video Balun
A
°
•
•
Troubleshooting:
Composite video balun does not function
correctly
y
Make sure all input and output connections are
connected firmly to the balun
y
Make sure the video input device is tu rned on
y
Make sure the video output device is turned on
y
Test the Cat5e/6 cable between the baluns
y
Make sure the RJ-45 connector is wired according to
T568B wiring standards
Specifications:
Max. range
Video format YPbPr or RGB (1080p/1080i/720p/720i/480p/480i)
Maximum input 1Vpp
Insertion loss Max. 2dB per pair over the freq. range from DC to 8MHz
Return loss Max. 2dB per pair over the freq. range from DC to 15MHz
Video
Common mode rejection Greater than 40dB at 8MHz
Bandwidth
Power No power required
Wire type UTP (unshielded twisted pair)
Wire category
Connectors
Connections
Dimensions 21/4” x 5/8” x 9/16” (57 x 16 x 14 mm) 2” x 7/8” x 3/4” (51 x 22 x 19 mm)
Humidity range 0 ~ 95%
Temperature Range
Other
Case PC plastic
Input RCA male RCA female
Output Terminal block
ttenuation DC ~ 5 Mhz, 1.5 dB max
MVE-PB010Q MVE-PB020Q
2,230’ (680m)
DC to 8MHz
20 - 24 AWG @ screwless terminal blocks
CAT5e or CAT6 for improved range
14°~165°F (-10
~74°C)
RJ-45
MANUAL
Passive Composite Video Baluns
HDMI over Cat5e/6
Also Available from SECO-LARM:
y
Component Video over Cat5e/6
y
Digital and Analog audio over Cat5e/6
WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2009 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in
whole or in part, without the written permission of SECO-LARM.
SECO-LARM
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
4 SECO-LARM U.S.A., Inc.
®
U.S.A., Inc.
Website: www.seco-larm.com
E-mail: sales@seco-larm.com
Mi-MVE-PB0x0Q.docx
PITLW2
PITSW4
MVE-PB010Q
(standard) (snap-in)
MVE-PB020Q
The ENFORCER Composite Video Baluns are the quick, low-cost way to connect composite or
component (YPbPr) video devices at greater distances than traditional video cabling methods. The
video baluns work in pairs to allow video signals to be transmitted up to 2,230’ (680m) over
low-cost Cat5e/6 unshielded twisted pair (UTP) cable instead of costly composite video cable.
Passive operation – No external power
required
• Uses low-cost Cat5e/6 cable instead of costly
composite video cables
• Small size for easy installation behind most
High immunity from interference – Built-in
impedance coupled device and noise filter
• Gold-plated connector for longer life and better
reliability
• Limited lifetime warranty
video devices
NOTE: Products with a model number that ends with “Q” or have a round green “Q” sticker represent RoHs compliant products.
ENFORCER Composite Video Balun
g Sy
Overview:
Shielding
Wire Exit Holes
(ground)
Modular Balun:
Center-pin
(positive)
Pin 7 (-) Pin 8 (+)
Snap-in Balun:
ENFORCER Composite Video Balun
5. Test the connection by powering up the video
source and destination.
6. If using standard baluns, replace the covers on the
video baluns and make sure the wires exit through
the two small holes on the back of the units.
NOTE: Bare wires must not be exposed
outside the video baluns.
Figure 3 – Video balun with
cover removed
Expose ¼” copper wire of the UTP for
connection to the balun. Use the “ideal
copper length” guide on the balun.
ENFORCER
Composite Video Balun
Ideal Copper Length
SECO-LARM
Cat5e/6
Shielding
(ground)
Please use T568B wiring standard for RJ45 connectors.
Installation:
NOTE: Composite baluns are connected in pairs. One connects to the video source RCA
output connector, and the other connects to the video destination RCA input connector.
1. Make sure the maximum distance between the video
source and display does not exceed the maximum range of
the video baluns.
2. Run the UTP cable from the video source to where it will
be connected to the display destination.
3. Connect UTP cable to the two video baluns.
For standard baluns slide the cover off of the video balun
and connect two wires to the terminal block located inside
the balun. See figure 1.
4. For the correct length of bare wire, see figure 3 on page 3.
For snap-in baluns connect the RJ 45 plug according to
T568B wiring standards. Plug the video baluns into the RCA
connectors on the source and destination.
NOTE: The baluns are polarity-sensitive. Observe
correct polarity.
Figure 1 – Video balun with
cover removed
Figure 2 – Connecting
Cat5e/6 Cable
Sample Application #1: Standard Composite Video Baluns
Composite Video
Source, VCR,
Gamin
stem
Sample Application #2: Modular Snap-in Composite Video Baluns
Composite Video
Source, VCR,
MVE-PB010Q
ENFORCER
MVE-PB020Q
MVE-PB010Q
ENFORCER
Up to 2,230’ (680m)
MVE-PB020Q
Display
Display
Gaming System
Up to 2,230’ (680m)
(wall plates not included)
Sample Application #3: Component Video
Component Video
Source
SECO-LARM has a complete line of audio/video products.
MVE-PB010Q
Y
Pb
Pr
ENFORCER
ENFORCER
ENFORCER
Up to 2,230’ (680m)
Please visit www.seco-larm.com for more information.
MVE-PB010Q
ENFORCER
ENFORCER
ENFORCER
Display
Y
Pb
Pr
2 SECO-LARM U.S.A., Inc.
SECO-LARM U.S.A., Inc 3
Loading...