Page 1
• Wirelessly extend HDMI signals up to
• Plug and play operation – comes as a
MVE-AH1W1-01NQ
Long-Range Wireless Extender for HDMI
Manual
656ft (200m)
• Supports resolutions from 480i to 1080p
with zero signal loss
• Two (2) 5VDC power supplies included
complete set
• IR Pass-through for remote control
extension
Page 2
ENFORCER Long-Range Wireless Extender for HDMI
Introduction:
Transmission frequency
5.1~5.9 GHz
Bandwidth
40MHz
Maximum single link range
1080p/60
Deep color
24-bit
Video formats supported
High-speed HDMI, HDCP 1.2
Audio formats supported
LPCM, Dolby-AC3, DTS7.1, DSD
Output video
HDMI
Resolutions supported
1080p/1080i/720p/576p/576i/480p/480i
Range
Up to 656ft (200m)*
Latency
<200ms
Antenna
8" (203mm) Omni-directional 5dBi
Encryption
AES 128
Video amplifier bandwidth
6.75Gbps
Video input connector
HDMI Type A 19-pin female
Maximum input cable length
24AWG: 32' (10m); 26AWG: 16' (5m); 28AWG: 10' (3m)
IR Pass-through
20~60 kHz
Operating voltage
5VDC
Power supply
5VDC/3A (2 adapters) (2.1mm plug)
ESD Protection (human body model)
±15kV (Air-gap discharge), ±8kV (Contact discharge)
draw
Transmitter
1.5A@5VDC
Receiver
1.3A@5VDC
Operating temperature
32°~140° F (°0~60° C)
Operating humidity
0~95% RH (non-condensing)
Dimensions
711/16"x57/16" x11/4" (195x138x31mm)
Transmitter
18.7-oz (531g)
Receiver
18.6-oz (528g)
Specifications:
• Wireless Transmission – Transmits high-definition video and audio wirelessly between the transmitter
Features:
The ENFORCER Long-Range Wireless Extender for HDMI sends high-definition audio and video wirelessly
easy installation. The extender also supports IR Pass-through for remotely controlling the HDMI source.
*Line-of-sight range. Actual range may vary depending on the installation and operating environment.
up to 656ft (200m)*. There are no cables required between the transmitter and receiver which makes for an
and receiver.
• Signal strength – Active operation ensures that the signal strength will remain strong.
• Range – The Long-Range Wireless Extender for HDMI provides a clear HDMI signal up to 656ft (200m)*.
• Formats Supported – The Long-Range Wireless Extender for HDMI supports both progressive and
interlaced formats: 1080p/1080i/720p/576p/576i/480p/480i.
• Plug and Play – The Long-Range Wireless Extender for HDMI comes as a complete set consisting of a
transmitter and receiver, antennas, power supplies, and IR dongles.
• IR Pass-through – Send IR signals from the HDMI source to the HDMI monitor for discrete operation
of devices.
Current
Weight
2 SECO-LARM U.S.A., Inc.
Page 3
Overview:
Installation:
1x
Transmitter
1x
Receiver
2x
5VDC/3A Power adapters
1x
Manual
1x
IR Transmitter (w/ double-sided tape)
1x
IR Receiver (w/ double-sided tape)
Parts List:
1. Determine the location where the Long-Range Wireless Extender for HDMI transmitter and
11/4" (31mm)
57/16" (138mm)
711/16"
(195mm)
HDMI Input (Transmitter) HDMI Output (Receiver)
RESET Button
Antenna
5VDC Input
Power LED
Data LED
(Slow blinking while
attempting connection.
while
.)
Link LED
IR Output (Transmitter)
IR Input
37/8" (98mm)
Fast blinking
transmitting/receiving data
ENFORCER Long-Range Wireless Extender for HDMI
(Receiver)
receiver will be installed.
NOTE: Do not install the transmitter or receiver units in corners or near other wireless
devices, as this may cause interference with the extender.
2. Connect the transmitter unit to the HDMI port of the source device via an HDMI cable.
3. Connect the receiver unit to the HDMI port of the monitor via an HDMI cable.
4. Install the IR transmitter to the IR-TX port of the transmitter unit, pointing the IR transmitter at
the device to be controlled. Install the IR receiver to the IR-RX port of the receiver unit,
pointing the IR receiver to where the remote control will be. Point the remote control at the
IR receiver when in use.
5. Connect the included power supplies to both the transmitter and receiver units.
6. Switch on the HDMI source device and HDMI display to verify that the system is functioning
properly.
NOTE: It may be necessary to press the receiver unit’s RESET button followed by the
transmitter unit’s RESET button after initial power-up to sync the unit.
7. If required, mount the transmitter and receiver units using the mounting holes (mounting
screws not included).
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Long-Range Wireless Extender for HDMI
• Make sure the extender is powered on both sides.
into the display using an HDMI cable.
• Switch the source device to a lower HDMI output
from any potential sources of interference
• Make sure that the power supplies of both transmitter and
receiver are firmly connected.
• Check to see that the transmitter unit and source device are
then press the RESET button on the transmitter unit.
®
PICLN3
MI_MVE-AH1W1-01NQ_161011.docx
HDMI Extender over
Single Cat5e/6
HDMI Extender over
Dual Cat5e/6
High-Speed
HDMI Cables
MVE-AH030Q
MVE-AH010Q
MC-1102-xxFQ
Also Available from SECO-LARM®:
FCC COMPLIANCE STATEMENT FCC ID: 2ADXC16WA88
COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
THIS DEVICE MUST ACCEPT
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
e antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate the device.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800
Email: sales@seco-larm.com
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
LARM’s obligation is limited to the repair or
This Warranty is void if
abuse, neglect, repair or alteration,
LARM determines that such equipment
e sole obligation of
’s
erty
damage of any kind to the purchaser or anyone else.
Troubleshooting:
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLCC in the
HDMI device does not function properly
• Make sure the source and display are powered.
• Make sure that there are no problems with the HDMI source,
HDMI cables or HDMI display by plugging the source directly
Screen flickering or brief image loss
Monitor displays "Waiting for connection…"
Monitor displays "Please check the TX input signal"
(i.e. 1080p to 1080i)
• Change the positioning of the transmitter and receiver away
powered on. Press the RESET button on the receiver unit
United States and other countries.
THIS DEVICE
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2)
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to th
service for three (3) years from the date of sale to the original customer. SECOreplacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
damage is caused by or attributed to acts of God, physical or electrical misuse or
improper or abnormal usage, or faulty installation, or if for any other reason SECOis not operating properly as a result of causes other than defects in material and workmanship. Th
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or prop
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints.
Copyright © 2016 SECO-
4 SECO-LARM U.S.A., Inc.
Loading...