Page 1
®
MVE-AH1T1-01YQ
HDMI Extender over Two Wires
Manual
1080p
Resolution
Features:
Extends HDMI over two wires
Supports resolutions from 480i to 1080p
with zero signal loss
Transmits up to 984ft (300m) at 1080p
over two wires
Plug and play operation – comes as
a complete set
Up to
984ft
(300m)
Range
RS-232
Pass-Through
HDMI Loop output for local HDMI display
Supports up to four (4) receivers for
multicast applications
Two (2) 12VDC power supplies included
Bi-directional RS-232 pass-through
IR Pass-through for remote control
extension and operation
IR
Up to 984ft (300m)
Pass-Through
Page 2
ENFORCER HDMI Extender over Two Wires
Introduction:
The ENFORCER HDMI Extender over Two Wires extends the range of traditional HDMI cabling
methods by using an active transmitter and receiver to send video and audio over any two
copper wires including Cat5e/6 cables, telephone wires, and coaxial cables. HDMI formats as
large as 1080p can be transmitted up to 984ft (300m) between the two units with zero signal loss
by using integrated circuits in the receiver and transmitter.
Table of Contents:
Introduction ..................................................................................................................................... 2
Table of Contents ........................................................................................................................... 2
Features ......................................................................................................................................... 2
Parts List ........................................................................................................................................ 3
Specifications ................................................................................................................................. 3
Overview ........................................................................................................................................ 4
IR Pass-through ............................................................................................................................. 5
HDMI Loop Output ......................................................................................................................... 5
Bi-directional RS-232 ..................................................................................................................... 5
Installation ...................................................................................................................................... 5
Sample Applications ................................................................................................................... 6~7
Troubleshooting .............................................................................................................................. 8
Also Available from SECO-LARM .................................................................................................. 8
Warranty ......................................................................................................................................... 8
Features:
Signal Strength – Active operation ensures signal strength remains strong over the length of
the wiring.
Distance – The HDMI Extender over Two Wires is capable of providing a clear HDMI signal
up to 984ft (300m).
Formats Supported – The HDMI Extender over Two Wires supports both progressive and
interlaced formats: 1080p/1080i/720p/576p/576i/480p/480i.
Plug and Play – The HDMI Extender over Two Wires comes as a complete set consisting of
a transmitter and receiver, power supplies, and IR dongles.
Zero Signal Loss – Integrated circuits in the transmitter and receiver clean, buffer, and
amplify the HDMI signal to prevent signal loss and ensure a clear signal.
IR Pass-Through – Send IR signals from the monitor to the source for discrete operation of
devices.
Bi-Directional RS-232 – Send RS-232 commands from a control system to the display and
back without extra cabling.
HDMI Loop Output – Secondary HDMI output for local displays.
Multicast Configuration – Supports up to 4 receivers for multicast applications.
2 SECO-LARM U.S.A., Inc.
Page 3
ENFORCER HDMI Extender over Two Wires
Parts List:
1x Transmitter (MVE-AH1T1-01YTQ) 2x Terminal 2-pin connectors
1x Receiver (MVE-AH1T1-01YRQ) 2x RS-232 3-Pin connectors
2x 12VDC Power adapters 1x IR Transmitter (with double sided tape)
1x Manual 1x IR Receiver (with double sided tape)
Specifications:
Input video signal 3.3V
Input DDC signal 5Vp-p (TTL)
Maximum single link range 1080p
Deep color 24bit
Video formats supported High-speed HDMI, HDCP 1.3
Audio formats supported PCM
Output video HDMI
Resolutions supported 1080p/1080i/720p/576p/576i/480p/480i
Range Up to 984' (300m)
Video input/output connector HDMI Type A 19-pin female
Max. input/output cable length 24AWG (15m), 26AWG (10m), 28AWG (5m)
IR Pass-through frequency 20~60 kHz
RS-232 Pass-through baud-rate Up to 115,200
Operating voltage 12VDC
Power supply 2A@12VDC (2 Adapters) (2.1mm plug)
ESD Protection
(human body model)
Current draw
Operating temperature 32°~140° F (0°~60° C)
Dimensions 51/8"x15/16"x37/16" (130x23x87 mm)
Weight 7.4-oz (210g) (Each)
Transmitter 625mA@12VDC
Receiver 580mA@12VDC
±8kV (Air-gap discharge), ±4kV (contact discharge)
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER HDMI Extender over Two Wires
tte
eceive
Overview:
Transmi
r MVE-AH1T1-01YTQ:
Data LED
(Slow blinking indicates
attempting connection.
Fast blinking indicates
transmitting/receiving data.)
Link LED
Reset button
51/8"
(130mm)
HDMI Input
HDMI Loop output
IR Transmitter port
RS-232 Port
(Ground/Receiver/Transmitter)
12VDC Input
Two-wire terminal port
15
/16" (23mm) 37/16" (87mm)
r MVE-AH1T1-01YRQ:
R
transmitting/receiving data.)
Data LED
(Slow blinking indicates
attempting connection.
Fast blinking indicates
Link LED
Reset button
51/8"
(130mm)
15
/16" (23mm) 37/16" (87mm)
HDMI Output
IR Receiver port
RS-232 Port
(Ground/Receiver/Transmitter)
12VDC Input
Two-wire terminal port
4 SECO-LARM U.S.A., Inc.
Page 5
ENFORCER HDMI Extender over Two Wires
IR Pass-Through:
The MVE-AH1T1-01YQ supports IR pass-through signals to allow for remote operation of the
source device from the display location. The IR transmitter and IR receiver support a frequency
range between 20~60 kHz.
HDMI Loop Output:
The MVE-AH1T1-01YQ includes a secondary HDMI output on the transmitter unit. This HDMI
output can be used for local displays that are in the same location as the HDMI source.
Bi-directional RS-232:
The MVE-AH1T1-01YQ supports bi-directional RS-232 data transmission to allow for control,
debugging, and monitoring from a connected control system.
Configuring Baud-Rate
1. To set the baud-rate (default: 9600) to match the baud-rate of the connected control system,
connect the control system to the MVE-AH1T1-01YTQ transmitter unit and connect the
MVE-AH1T1-01YRQ receiver unit to the remote device to be controlled.
2. Once connected, use the desired RS-232 software on the control system to set the correct
baud-rate. The MVE-AH1T1-01YQ supports the following baud-rates: 2400 / 4800 / 9600 /
19200 / 28800 / 38400 / 57600 / 115200.
Installation:
1. Determine the location where the MVE-AH1T1-01YQ units will be wired as well as length of
two conductor wire necessary.
2. Connect the transmitter to the HDMI output of the source device.
3. Connect two copper conductor wires to the terminal ports on both the receiver and
transmitter units. Any two copper wires will work, including network Cat5e/6 cables,
telephone wires, and coaxial cables. Shielded wiring is recommended to avoid cross-talk
and digital noise.
NOTE: The maximum length of conductor wire for all installations is 984ft (300m).
4. Connect the receiver to the HDMI input of the display or other device.
5. Connect one 12VDC adapter to the transmitter and the other 12VDC adapter to the receiver.
6. Install the IR transmitter to the IR-TX port located on the transmitter unit, pointing the
IR transmitter at the device to be controlled.
7. Install the IR receiver to the IR-RX port located on the receiver unit, pointing the IR receiver
to where the remote control will be. Point the remote control at the IR receiver when in use.
8. Connect an RS-232 controller unit to the MVE-AH1T1-01YTQ transmitter unit and connect
the MVE-AH1T1-01YRQ receiver unit to the remote device to be controlled.
9. Switch on the HDMI source and display to verify that the system is functioning properly.
SECO-LARM U.S.A., Inc. 5
Page 6
ENFORCER HDMI Extender over Two Wires
play
play
p
play
play
p
play
play
play
Sample Applications:
One Transmitter, One Receiver:
Local
Dis
Cable Legend:
HDMI
Two wires
RS-232
Power
IR
RS-232 Control Panel
12VDC Ada
IR Transmitter
HDMI Source
ter
Two-wire connection
Up to 984ft (300m)
12VDC Adapter
One Transmitter, Multiple Receivers (Up to 4), Cascaded Wiring:
NOTE: Do not bundle two-wire cabling when connecting
multiple receivers.
12VDC Adapter
Two-wire connection
Local
Dis
RS-232 Control Panel
12VDC Ada
ter
Up to 984ft (300m)*
12VDC Adapter
12VDC Adapter
IR Receiver
IR Receiver
IR Receiver
Remote
Dis
Remote
Remote
Dis
Remote
Dis
Remote
Remote
Dis
IR Transmitter
HDMI Source
12VDC Adapter
IR Receiver
Remote
Dis
* When connecting multiple receivers, the combined length of two-wire
cabling must not exceed the maximum range of 984ft (300m).
IR Receiver
6 SECO-LARM U.S.A., Inc.
Page 7
ENFORCER HDMI Extender over Two Wires
play
play
play
play
play
p
Sample Applications (Cont.):
One Transmitter, Multiple Receivers (Up to 4),
Daisy-Chain Wiring:
NOTE: Do not bundle two-wire cabling when connecting
multiple receivers.
Cable Legend:
HDMI
Two wires
RS-232
Power
IR
Local
Dis
RS-232 Control Panel
12VDC Ada
IR Transmitter
HDMI Source
12VDC Adapter
Two-wire connection
Up to 984ft (300m)*
IR Receiver
12VDC Adapter
Remote
Dis
Remote
Remote
Dis
ter
IR Receiver
12VDC Adapter
Remote
Remote
Dis
IR Receiver
12VDC Adapter
Remote
Remote
Dis
* When connecting multiple receivers, the combined length of two-wire
IR Receiver
cabling must not exceed the maximum range of 984ft (300m).
Remote
SECO-LARM U.S.A., Inc. 7
Page 8
ENFORCER HDMI Extender over Two Wires
(
Troubleshooting:
HDMI device does not function correctly
Verify the extender is powered on both sides
Verify the source and the display are powered
Test the two conductor wires between the receiver and
transmitter to confirm they are functional
Verify that there are no problems with the HDMI source,
HDMI cables, or HDMI display by plugging the source
directly into the display using an HDMI cable
Do not bundle cables when connecting multiple receivers
Screen flickering or brief image loss
Switch the source device to a lower HDMI output
(e.g., 1080p to 1080i)
Also Available from SECO-LARM®:
HDMI Extender over
Single Cat5e/6
MVE-AH030Q MVE-AH1E1-01NQ MC-1130-xxFQ
4K HDMI Splitters HDMI Extender over IP
HDMI Extender over
Single Cat5e/6
High-Speed
HDMI Cables
Enhanced HDMI Extenders
over Single Cat5e/6
MVD-AH1x-01Q MVE-AHMPM-01NQ MVE-AH1H1-0xxQ
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
WARRANTY:
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2018 SECO-LARM U.S.A., Inc. All
rights reserved.
SECO-LARM
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone:
949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
MI_MVE-AH1T1-01YQ_180122.docx
®
PICLN3
8 SECO-LARM U.S.A., Inc.
Loading...