Page 1
in the United States and other countries.
HDMI Extenders with KVM
Installation Manual
MVE-AH1E1-01UQ shown
Up to
KVM
Model Resolution Video support Audio support
MVE-AH1E1-01UQ Up to 1080p
MVE-AH1E1-42UQ Up to 4K@60Hz
230ft
(70m)
Range Control
Cat6
High-speed HDMI,
HDCP 1.4
High-speed HDMI,
HDCP 2.2
Up to
4K@60Hz*
Resolution Single Cable
*MVE-AH1E1-42UQ only
PCM, LPCM, DTS-HD, DTS-Audio
LPCM, DTS-HD, DTS-Audio,
Dolby Digital 5.1CH
The ENFORCER HDMI Extenders with KVM allow you to transmit HDMI audio and video as well
as a USB (2.0) signal up to 230ft (70m) over a single Cat6 cable using an active transmitter and
receiver, allowing remote operation of a device such as a computer or NVR/DVR. The extenders
also provide HDMI loop-out and KVM.
• Display up to 4K@60Hz (MVE-AH1E1-42UQ only)
• Zero latency transmission up to 230ft (70m) over single Cat6/7
• Supports USB keyboard and mouse (KVM)
• Supports point to point connections
• Transmitter includes HDMI loop-out
• Lightning Protection, surge protection, and ESD protection.
• Receiver has L/R audio outputs (MVE-AH1E1-01UQ only)
• Receiver has an optical S/PDIF out if an AVR or sound bar is fitted in the remote location
(MVE-AH1E1-42UQ only)
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC
Page 2
Parts List
1x Transmitter
1x Receiver
2x Power supplies*
1x
USB Cable
HDMI Extenders with KVM
8x
Mounting brackets
*
5VDC@1A for MVE-AH1E1-01UQ / 5VDC@2A for MVE-AH1E1-42UQ
†
18x
Mounting screws
†
1x Manual
†
MVE-AH1E1-42UQ only
Specifications
Model MVE-AH1E1-01UQ MVE-AH1E1-42UQ
Input Video signal 3.3V
Input DDC signal 5Vp-p (TTL)
Maximum single link range 230ft (70m)
Video formats supported High-speed HDMI, HDCP 1.4 High-speed HDMI, HDCP 2.2
Audio formats supported PCM, LPCM, DTS-HD, DTS-Audio
Output video HDMI
1080p,1080i, 720p, 576p, 576i, 480p,
Resolutions supported
Range (Cat6/6A/7) Up to 230ft (70m)
Video input connector HDMI Type A 19-pin female
Maximum input cable length 26ft (8m) AWG24
Video output connector HDMI Type A 19-pin female
Maximum output cable length 26ft (8m) AWG24
Cat6 Wiring standard T-568B
Operating voltage 5VDC 5~12 VDC
Power supply 5VDC@1A 5VDC@2A
ESD Protection ±8kV (air-gap discharge), ±4kV (contact discharge)
Current
draw
Operating humidity 0~90%
Operating temperature -4°~140° F (-20°~60° C)
Dimensions 215/16"x33/8"x3/4" (74x85x19 mm) 513/16"x41/2"x1" (148x105x25 mm)
Weight 6.3-oz (180g) 9.2-oz (260g)
Transmitter <2.5W <4W
Receiver <2.5W <4W
480i, 1920x1080, 1680x1050,
1440x900, 1366x768, 1280x960,
1280x720, 1024x768, 800x600
LPCM, DTS HD, DTS Audio,
Dolby Digital 5.1CH
4K@60Hz, 4K@30Hz, 1080p, 1080i,
720p, 576p, 576i, 480p, 480i,
1680x1050, 1680x1050, 1600x900,
1366x768, 1360x768, 1280x960,
1280x800, 1280x720, 1024x768,
800x600
Installation
1. Determine the installation locations for the transmitter and receiver and length of cable needed.
2. Connect the transmitter to the source device HDMI output.
3. Connect the Cat6/7 cable to the receiver and transmitter.
4. If using the HDMI loop out, connect the display to the transmitter HDMI OUT port.
5. Connect the receiver to the HDMI input of the display or other device.
6. Connect a computer to the transmitter USB port using the included USB cable.
7. Connect a USB keyboard and USB mouse to the receiver USB ports.
8. Connect any audio devices as needed.
2 SECO-LARM U.S.A., Inc.
Page 3
HDMI Extenders with KVM
2
3
1
4
5
1
6
6
7
8
2
3
4
5
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
6
7
8
5
1
2
3
4
2
3
1
4
6
7
8
5
Installation (Continued)
9. Connect the power adapters to the transmitter and receiver and plug in to the electrical outlet.
10. Switch on the HDMI source and display to verify that the system is functioning properly.
INSTALLATION NOTES
• Do not place in locations that may be exposed to rain or any other moisture or liquids.
• Disconnect all devices from power before beginning installation to avoid potential damage.
• Do not install near heat sources or confined spaces with inadequate ventilation.
• The use of a single shielded Cat6/7 or better cable is strongly recommended.
Overview
MVE-AH1E1-01UQ Transmitter
215/16"
(74mm)
MVE-AH1E1-01UQ Receiver
33/8"
(85mm)
Reset button Power LED indicator
2 Cat6 Out HDMI In
USB Port HDMI Out
KVM LED indicator Power 5VDC
MVE-AH1E1-42UQ Transmitter
3
/4"
(19mm)
The receiver and transmitter are the same size.
Reset button Power LED indicator
Cat6 In HDMI Out
USB Ports (x2) Speaker Out
KVM LED indicator Power 5VDC
MVE-AH1E1-42UQ Receiver
513/16"
(148mm)
41/2"
(105mm)
Power 5VDC Power LED indicator
HDMI Out Cat6 Out
HDMI In Reset button
USB Port KVM LED indicators (x2)
1"
(25mm)
The receiver and transmitter are the same size.
Power 5VDC Power LED indicator
S / PDIF Out Cat6 In
HDMI Out Reset button
USB Ports (x2) KVM LED indicators (x2)
SECO-LARM U.S.A., Inc. 3
Page 4
HDMI Extenders with KVM
Speaker
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
from the date of sale
id, to
on, improper
operating properly as a result of causes other
LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair
LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind
LARM reserves the right to change specifications without
2021
alifornia to cause cancer and birth defects or other
aws and statutes related to
Sample Application
Power supply
Transmitter
MVE-AH1E1-01UQ shown
Power supply
Receiver
Local
Display
HDMI source
Troubleshooting
HDMI device does
not function
correctly
Screen flickering or
brief image loss
Speakers
Cat6 cable
up to 230' (70m)
Computer
Cable Legend
HDMI
Cat6
USB
Power
Keyboard
Remote
Display
Mouse
• Use T568-B wiring standard
• Make sure the extender is powered on both sides
• Make sure the source and display are powered
• Test the cable between the receiver and transmitter to make sure it is functional
• Make sure there are no problems with the HDMI source, HDMI cables, or HDMI
display by plugging the source directly into the display using an HDMI cable
• Use a higher grade of twisted pair category cable (Cat6/7 is recommended)
• Switch the source device to a lower HDMI output (e.g., 1080p to 1080i)
• Restart the handshake process by powering everything down then powering up
and connecting each device in succession starting with the HDMI source
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local l
monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
California Proposition 65 Warning: These products may contain chemicals which are known to the State of C
reproductive harm. For more information, go to www.P65Warnings.ca.gov.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for two (2) years
to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepa
SECO-LARM. This Warranty is void if damage is caus ed by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alterati
or abnormal usage, or faulty installation, or if for any oth er reason SECO-LARM determines that such equipment is not
than defects in material and workmanship. The sole obligation of SECOonly, at SECO-LARM’s option. In no event shall SECOto the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECOnotice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright ©
SECO-LARM U.S.A., Inc. All rights reserved.
SECO-LARM
Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
®
U.S.A., Inc.
MI_MVE-AH1E1-xxUQ_211111.docx
PICLN3
Loading...