Seco-Larm LS-313A-14Q, LS-525A-14Q Installation Manual

Download

Page 1

Features:

•

ets with one button, or

one outlet with multiple remotes

Remote is compatible with both Wireless

Outlets and Wireless Light Sockets

Combine several kits for further expansion

vary depending on the installation and operating environment

3 Wireless Outlets, 1 Remote

Outlets, 2 Remotes

Conforms to UL 61058

Certified to CSA C22.2 NO.61058

1 and 498A

Wireless Outlet Controller

Manual

-1 and 42

Model # Included in kit

LS-313A-14Q

LS-525A-14Q 5 Wireless

Wirelessly control devices, appliances, or

lamps up to 100ft (30m) away*

• Energy saving – Wireless Outlet draws zero power when off

• Easily expand to multiple devices by pairing to different channels or remotes

Line-of-sight range. Actual range may

Control multiple outl

•

• For indoor use only

Page 2

CBA Wireless Outlet Controller

Specifications:

3x Wireless Outlets

Remote

12VDC (23A) Battery

Manual

5x Wireless Outlets

Remotes

12VDC (23A) Batteries

Manual

Wireless Outlet

Outlet

Pairing button

LED Indicator

Remote

LED Indicator

Channel 1

Battery

Line-of-sight range. Actual range may vary depending on the installation and operating environment

Overview:

Parts List:

LS-313A-14Q

LS-525A-14Q

Model LS-313A-14Q LS-525A-14Q

Wireless Outlets included 3 5 Remotes included 1 2 # of Remote channels 3 5 Working voltage 120V~/60Hz Remote battery 12VDC (23A) (included) Max. load for each Wireless Outlet 1200W (10A) Transmission frequency 433.92MHz Remote range 100ft (30m)* Operating temperature 59°~95° F (15°~35° C)

Dimensions

Wireless Outlet 21/8"x311/16"x17/16" (54x94x36 mm)

Remote

11/2"x35/16"x11/16"

(38x84x18 mm)

11/2"x41/8"x11/16"

(38x105x18 mm)

(LS-525A-14Q shown)

ON button

OFF button

compartment

2 SECO-LARM U.S.A., Inc.

Page 3

CBA Wireless Outlet Controller

Installation and Setup:

Remote Battery Installation:

General Operation Instructions:

1. Each

Wireless Outlet

is numbered corresponding to one of the remote buttons to which it is

1. Slide the battery cover on the back of the remote down to reveal the battery compartment.

1. Press the ON button on the remote to turn on all

Wireless Outlet

s on that channel. Press the

2. Insert one 12V (23A) battery (included) making sure to observe correct polarity.

3. Slide the battery cover back into place.

paired. Choose one of the Wireless Outlets and plug it into a powered outlet.

2. Plug the desired device or appliance into the Wireless Outlet.

3. To switch the outlet on, simply press the corresponding button on the remote. The outlet may

also be controlled manually by pressing the pairing button momentarily.

Pairing with a Remote:

1. To pair additional Wireless Outlets, or to change the channel of an existing Wireless Outlet

begin with the Wireless Outlet plugged in.

2. Press and hold the pairing button until the LED indicator begins to flash. Release the pairing

button (pairing mode is active for 10 seconds).

3. Press the ON or OFF button on the remote for the desired channel.

4. Pairing is successful when the LED indicator on the Wireless Outlet stops flashing.

5. Repeat with other Wireless Outlets. Multiple outlets may be paired to the same or separate channels. Each outlet may be paired with multiple channels or remotes (up to 3 pairings).

Clearing All Pairings:

1. Unplug any devices connected to the Wireless Outlet and remove it from the power outlet.

2. Press and hold the pairing button on the Wireless Outlet.

3. While holding the pairing button, plug the Wireless Outlet back into a power outlet.

4. Continue holding the pairing button until the LED indicator flashes rapidly, then stops. This indicates that all pairings for that Wireless Outlet have been cleared.

corresponding OFF button on the remote to turn them off.

2. When power returns after an outage, the Wireless Outlets will remain off until turned on again to reduce the risk of fire and save energy.

3. Wireless outlets can also be turned on/off manually by pressing the pairing button momentarily.

NOTE:

1. Each button on a remote can be paired with an unlimited number of Wireless Outlets, but each Wireless Outlet can only have 3 pairings.

2. Avoid exposure to high temperatures and strong sunlight.

3. Avoid use in areas with high humidity, such as bathrooms.

4. Do not exceed the maximum load of 1200W (10A).

5. If the LED on the remote becomes dim or intermittent, replace the battery.

6. The Wireless Outlets are for indoor use only.

SECO-LARM U.S.A., Inc. 3

Page 4

CBA Wireless Outlet Controller

Ensure the Wireless Outlet is powered and any switch for that

Make sure there is a fresh battery in the remote

with the remote

within the range of the outlet

with good air

Make sure there is no other RF interference

Troubleshooting:

16842 Millikan Avenue, Irvine, CA 92606

Website:

www.seco

larm.com

Phone: (949) 261

2999 | (800) 662

0800 Email: sales@seco

larm.com

NOTICE

The SECO

LARM policy

is one of continual development and improvement. For that reason, SECO

LARM is also not responsible for misprints.

SECO

WARRANTY:

This SECO

-LARM product is warranted against defects in material and workmanship while

LARM’s obligation is limited to the repair or

LARM.

damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,

LARM determines that such equipment

is not operating properly as a result of causes other than defects in material and workmanship.

eplacement or repair only, at

LARM be liable for any special, collateral, incidental, or consequential personal or property

IMPORTANT

Users and installers of this product are responsible for ensuring this product

state, and local laws and statutes related to monitoring and recording audio and video signals. SECO

FCC COMPLIANCE

STATEMENT

LS-

T341Q FCC ID: Q92

-BH-

U LS

T541Q FCC ID: Q92

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Notice: The changes or modifications not expressly approved by the party responsible for compliance cou

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the

device is permitted. Any change to the antenna or the device could result in the device excee

requirements and void user’s authority to operate the device.

SECO

LARM

Wireless Doorbell

Wireless Motion Alert

Parking Alert

AC-132Q

RC-

135Q

MI_LS-xxxA-14Q_170713.docx

LARM

rademarks

Inc. All

used in normal

This Warranty is void if

The sole obligation of

’s

with all national,

will not be

-BH-V

ld void the user’s

ding the RF exposure

AS-7021

Wireless outlet does not work

•

outlet is on

•

• Clear outlet pairing and pair

• Ensure that the remote is

• Ensure that the outlet is in a location

not overheated

• Move to another location and try again

Short remote range

Also Available from

• Replace remote battery

•

held responsible for the use of this product in violation of any current laws or statutes.

again

ventilation and is

complies

-LARM

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2)

authority to operate the equipment.

service for one (1) year from the date of sale to the original customer. SECOreplacement of any defective part if the unit is returned, transportation prepaid, to SECO-

improper or abnormal usage, or faulty installation, or if for any other reason SECO-

SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the r option. In no event shall SECOdamage of any kind to the purchaser or anyone else.

SECO-LARM

All t

-LARM U.S.A.,

U.S.A., Inc.

4 SECO-

PICBN1