
Helps prevent damage to sensitive networking equipment
Intercepts repeated surges and spikes that could damage network
equipment
Installs on a Cat5e/6 4-pair UTP cable with RJ45 jacks
Power and signal line protection
10/100 Base-T Cat5/5e compatible
Support mid-span PoE and end-span PoE
Complies with 802.3af and 802.3at for PoE
Includes a 16” grounding wire for convenient connection to ground
PoE (Power over Ethernet) Surge Protector

ENFORCER PoE (Power over Ethernet) Surge Protector
Signal passing
capability
The ENFORCER PoE (Power over Ethernet) Surge Protector is a passive device that helps protect
sensitive networking equipment from power surges. The device can be deployed in new
installations or added to existing ones.
The ENFORCER PoE Surge Protector should be installed between the PoE hub and a networked
device to protect against surges that could damage the equipment.
NOTE: For the best protection, installing two surge protectors is recommended: one at each end of
2 SECO-LARM U.S.A., Inc.

ENFORCER PoE (Power over Ethernet) Surge Protector
1. Each of the two PoE Surge Protectors should be mounted as close as possible to the devices that are to
be protected.
2. Detach the existing Cat5e/6 cables from the devices to be protected (such as a PoE switch and IP
Camera) and attach them to end of their corresponding PoE Surge Protector marked “Cable End.”
3. Prepare and connect an additional Cat5e/6 cable to each device to be protected and to the end of its PoE
Surge Protector marked “Equipment End.” For best protection, these cables should be the shortest length
possible to connect the PoE Surge Protectors and the protected devices. In addition the protected cables
should not cross unprotected cables.
4. Connect the ground wires from the PoE Surge Protectors to earth ground. The system should use a
single ground point and the protected device should be isolated from ground.
Protecting a Single Device:
1. The PoE Surge Protector should be mounted as close as possible to the device that is to be protected.
2. Detach the existing Cat5e/6 cable from the device to be protected and attach it to end of the PoE Surge
Protector marked “Cable End.”
3. Prepare and connect an additional Cat5e/6 cable to the device to be protected and to the end of the PoE
Surge Protector marked “Equipment End.” For best protection, this cable should be the shortest length
possible to connect the PoE Surge Protector and the protected device. In addition the protected cables
should not cross unprotected cables.
ground point and the protected device should be isolated from ground.
Protecting Multiple Devices:
NOTE: These instructions assume that 2 PoE devices have already been connected together.
PoE Switch
(Not Protected)
Shortest Possible
Cat5e/6 cable
Shortest
Possible Cat5e/6
cable
Shortest
Possible Cat5e/6
cable
SECO-LARM U.S.A., Inc. 3

ENFORCER PoE (Power over Ethernet) Surge Protector
Also Available from SECO-LARM:
Wavy or ghost video image if connected to
an image processor (e.g., multiplexer or
DVR), but not if connected directly to the
monitor.
Video image background flutters between
dark and light.
Video image is weak or faded.
specifications in the manual. Cat6 cable allows longer
range.
Video Surge Protector
VS-1V12BQ
IP Surge Protector
IPV-PD88Q
HD-SDI Surge Protector
VS-1V22AQ
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
Website: www.seco-larm.com
E-mail: sales@seco-larm.com
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the
written permission of SECO-LARM.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local
laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING: Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock,
damage the device, and void the warranty. Do not open the case of this device, as there are no field-serviceable components inside.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating
properly as a result of causes other than defects in material an d workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any
kind to the purchaser or anyone else.
4 SECO-LARM U.S.A., Inc.