Seco-Larm EV-Y5105-N2SQ User Manual

Download

Page 1

Features:



4-in-1 HD TVI, CVI, AHD, Analog

EV-Y5105-N2SQ

Wall-Plate Camera

Manual

Select between multiple formats:

TVI, CVI, AHD, and Analog

 1/

" 2MP Sony STARVIS CMOS

2.8

 2.9mm Wide angle lens  Weatherproof IP67 construction  Vandal-resistant design

Adjustable mounting angle

 Includes: 1 camera, 1 single-gang plate,

1 slimline plate, and angled mounting rings

 2DNR (2D Digital Noise Reduction)  D-WDR (Digital Wide Dynamic Range)  12VDC Operating voltage

Page 2

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Wall-Plate Camera

Dimensions:

Specifications:

1x Camera

Single-gang plate

Slimline plate

Angled rubber ring

1x Angled aluminum ring

Aluminum hex nut

OSD

Joystick

Mounting screws

1x Manual

Camera

body

/8"

(22mm)

Slimline plate

Single

gang plate

Type Wall-plate camera Formats TVI (Default) / CVI / AHD / Analog Plate type 1 Single-gang, 1 slimline CMOS Resolution 1080p 2DNR Yes D-WDR Yes OSD (On-Screen Display) Yes External OSD Control Yes Scanning system 2:1 Interface Sync Internal Video output 1.0Vp-p Complex video, 75Ω Lens 2.9mm Viewing angle 120° FPS 30FPS F Stop 2.2 Minimum illumination Color: 0.01Lux, BW: 0.001Lux Gamma correction 0.45 S/N Ratio 50dB Gain control Auto Operating voltage 12VDC Current draw 130mA±15% IP Rating IP67 Operating temperature 14°~122° F (-10°~50° C)

Dimensions

Camera body weight 2.8-oz (80g)

Parts List:

Camera 17/16"xø11/8"(36xø28 mm) Single-gang plate 23/4"x41/2" (70x114 mm) Slimline plate 11/2"x41/2" (38x114 mm)

" 2MP Sony STARVIS CMOS

2.8

(114mm)

23/4" (70mm)

41/2"

(114mm)

11/2" (38mm)

17/16" (36mm)

11/8"

(28mm)

11/8"

(28mm)

2 SECO-LARM U.S.A., Inc.

Page 3

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Wall-Plate Camera

Overview:

Before Starting:

Mounting the Camera to the Plate:

Mounting Options:

Changing the Mounting Angle:

1. Read this manual carefully and keep it for future

4. Do not mount the camera in areas exposed to

DC Jack

To mount the camera to the plate, position the angled

Inst

all the angled rubber ring on the front of the plate

If an object installed next to the camera on the wall

Mount directly to the back box (not included).

Drill a

/8" (22mm)

hole in the wall to fit

the

camera

Drill a

/8" (22mm) hole into

the wall to fit

the

camera

With a plate and back box

(suggested)

: Plate, no back box:

No p

late and no b

ack box:

Min. Wall thickness:

/16" (8mm)

Max. Wall thickness:

/16" (23

mm)

IMPORTANT:

Do not cut the video or p

ower wires

Plate

Camera

Female BNC connector

Aluminum hex nut

OSD Joystick

OSD Cable

reference.

2. Use the camera within given temperature and electrical limits.

3. Do not point the camera at the sun. Heat could damage the camera, even when not in use.

radiation, strong magnetic fields, or strong electrical signals.

5. Do not open or disassemble the camera. There are no user-serviceable parts inside.

6. Do not subject the camera to extreme shock.

Angled rubber ring

Note polarity when connecting

Angled aluminum ring

as warranty will be voided.

NOTE: When installing the camera. Ensure that the arrow label behind the lens is at the top.

rings behind the plate and twist the aluminum hex nut on to secure the plate to the camera.

Back

box

is blocking the field of vision, the angled rings may be installed in front of the wall plate to move the field of vision forward.

so that the camera is tilted (approximately 20°).

body. Mount the plate directly to the wall.

body. If mounting to a thick surface, it may not be necessary to use the angled rings.

SECO-LARM U.S.A., Inc. 3

Page 4

ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Wall-Plate Camera



Troubleshooting:

16842 Millikan Avenue, Irvine, CA 92606

Website:

www.seco

larm.com

Phone: (949) 261

2999 | (800) 662

0800 Email: sales@seco

larm.com

ITSW1

Order Part# 764

100-10%

MI_EV-Y5105-N2SQ_181207.docx

NOTICE

The SECO

LARM policy is one of continual development and improvement. For that reason, SECO

LARM

rademarks

Inc. All

WARRANTY:

This SECO

LARM product is warranted against

defects in material and workmanship while

used in normal

LARM’s obligation is limited to the repair or

This Warranty is void if

damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,

ARM determines that such equipment

The sole obligation of

’s

LARM be liable for any special, collateral, incidental, or consequential personal or property

IMPORTANT

with all national,

will not be

FCC COMPLIANCE STATEMENT

Switching between HD Analog Outputs:

To set format via the OSD controller, press the

Direction

Format Setting

CVI

Down TVI

Left CVBS Right AHD

DOWN

L R

controller in the direction of the desired setting, hold for 5 seconds, and release when the camera restarts. See chart to the right.

The screen is blank

The screen image is dim

The screen image has poor contrast

The screen image flickers

The screen image is distorted

The camera case is hot

Check that the camera is powered up

 Check that the power supply's polarity is correct  Check that the monitor is powered up  Check that the video cable connecting the camera to the monitor

is connected properly

 Verify video format

Clean the lens using a soft, clean cloth

 Change the position of the camera  Verify video format

Adjust the monitor's contrast knob

 Change the position of the camera  Verify video format

Change the position of the camera

 Verify video format

Change the position of the camera

 Verify video format

Check that the correct power supply is in use

state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM held responsible for the use of this product in violation of any current laws or statutes.

Users and installers of this product are responsible for ensuring this product complies

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

service for three (3) years from the date of sale to the original customer. SECOreplacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

improper or abnormal usage, or faulty installation, or if for any other reason SECO-L is not operating properly as a result of causes other than defects in material and workmanship. SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM option. In no event shall SECOdamage of any kind to the purchaser or anyone else.

reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All t are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2018 SECO-LARM U.S.A., rights reserved.

U.S.A., Inc.

4 SECO-LARM U.S.A., Inc.