Page 1
Features:
Select between multiple formats:
TVI, CVI, AHD, and Analog
1
/
2.9
" 2MP Sony CMOS
Full HD (1920x1080) resolution
True Day & Night function with
ICR mechanism
3D-NR (3D Noise Reduction)
DWDR (Digital Wide Dynamic Range)
Built-in internal joystick OSD control
Vandal-resistant metal front panel
Weatherproof (IP65)
30 Covert IR LEDs for discreet monitoring
EV-Y4201-A2SQ
4-in-1 HD TVI, CVI, AHD, Analog
Corner-Mount Camera
Manual
Page 2
ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Corner-Mount Camera
Specifications:
Dimensions:
1x
Camera
1x
Camera cover
1x
Security wrench
1x
Manual
1x
Pigtail connector
3x
Security screws
2x
Mounting screws
Parts List:
Model
EV-Y4201-A2SQ
Housing color
Silver
Type
Corner-Mount Camera
Formats
TVI (default) / CVI / AHD / Analog
CMOS
1
/
2.9
" 2MP Sony CMOS
Resolution (HD)
1920x1080
TV Lines (Analog)
1200TVL
3D-NR
Yes
2D-NR
Yes
DWDR
Yes
OSD (On-Screen Display)
Yes
Onboard OSD control
Yes
Video output
1.0Vp-p complex video output
Megapixels
2MP
Lens
2.9mm ICR
Viewing Angle
130°
# of IR LEDs
30
IR Range
Up to 82ft (25m)
FPS
30FPS
F Stop
F1.8
Minimum
illumination
(IR On)
0Lux
(IR Off)
Color: 0.2Lux/F1.8, B/W: 0.02Lux/F1.8
Gamma correction
0-1
S/N Ratio
50dB
DSS (Digital Slow Shutter)
Yes
Shutter control
Auto
Gain control
Auto
White balance
Auto, Day & Night
Operating voltage
12VDC
Current Draw
(IR On)
400mA
(IR Off)
80mA
IP Rating
IP65
Operating temperature
14°~122° F (-10°~50° C)
Dimensions
71/2"x51/2"x111/16" (190x140x43 mm)
Weight
13.75-oz (390g)
111/16"
(43mm)
71/2" (190mm)
51/2"
(140mm)
2 SECO-LARM U.S.A., Inc.
Page 3
ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Corner-Mount Camera
Overview:
Important: Do not cut DC jack or BNC jack as warranty will be voided.
Installation:
Before Starting:
Camera cover
Security screw
OSD Controller Settings:
To set format via the OSD controller,
press the controller in the direction of
the desired setting, hold for 5 seconds,
and release when the camera restarts.
See chart below.
Direction
Format Setting
Up
CVI
Down
TVI
Left
CVBS
Right
AHD
Mounting screws
DC jack
Pigtail connector
BNC jack
Joystick
OSD Control
CVI
TVI
(Default)
AHD
CVBS
1. Run a 12VDC power supply wire and a video cable with
a male BNC connector through the wall at the corner
where the camera is to be mounted.
2. Do not cut DC jack or female BNC connector as
warranty will be voided. If needed, use the included
pigtail connector.
3. Use the included security wrench to loosen the screws
and remove the camera cover from the camera.
4. Connect the power supply and video cable. Turn the
monitor on and make sure the camera is sending the
proper signal.
5. While watching the monitor, hold the camera against
the corner where it is to be mounted until it is certain
that this mounting location is correct. Use a pencil to
mark the location of the two screw holes.
6. Disconnect the power supply and video cable.
7. Mount the camera against the corner using the two
included mounting screws. If the wall is made of dry
wall, brick, or similar material, it may be necessary to
use screw anchors (not included).
8. Reconnect power and video.
9. Reattach the camera cover using the included
security wrench.
10. Do a final test of the video camera and monitor.
1. Use the camera within given temperature and
electrical limits.
2. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
3. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong electrical
signals.
4. Do not drop the camera or subject it to strong
vibrations.
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Corner-Mount Camera
®
PIKSR1
MI_EV-Y4201-A2SQ_161011.docx
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be
held responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate the device.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800
Email: sales@seco-larm.com
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints.
Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Troubleshooting:
The screen is black
Check that the camera is powered up
Check that the power supply’s polarity is correct
Check that the monitor is powered up
Check that the video cable connecting the camera to the monitor is
connected properly
The image is foggy or washed out at night
Check that there are no objects very close to the camera
Check that there are no highly reflective objects in the scene
The screen image is dim
Clean the lens using a soft, clean cloth
Check that the light source is adequate
The screen image has poor contrast
Adjust the monitor’s contrast knob
Change the position of the camera
The screen image flickers
Change the position of the camera, check cables and format
setting
The screen image is distorted
Change the position of the camera, check cables and format
setting
The camera case is hot
Check that the correct power supply is in use
IR LEDs do not turn on
Check that the correct power supply is in use
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock.
Do not open the case of this device, as there are no user-serviceable components inside.
4 SECO-LARM U.S.A., Inc.
Loading...