Seco-Larm EV-Y2201-AMWQ, EV-Y2201-A2GQ, EV-Y2201-AMGQ, EV-Y2201-A2WQ User Manual

4-in-1 HD TVI, CVI, AHD, Analog

Manual

EV-Y2201-AMWQ shown

• 1080p Resolution

•

•

•

•

• Heavy-duty vandal-resistant design

•

•

•

Features:

Model #

Lens

Resolution

Voltage

Style

Color

EV-Y2201-A2WQ

2.8mm

1080p

12VDC

Rollerball

White

EV-Y2201-A2GQ

2.8mm

1080p

12VDC

Rollerball

Gray

EV-Y2201-AMWQ

2.8~12mm

1080p

12VDC

Rollerball

White

EV-Y2201-AMGQ

2.8~12mm

1080p

12VDC

Rollerball

Gray

Rollerball Cameras

ICR Module
3D-NR (3D Digital Noise Reducti on)
DWDR (Digital Wide Dynamic Range)
Joystick OSD control

Rugged, weatherproof (IP65) construction
Split-glass design eliminates IR reflection
Cables concealed in bracket to

prevent tampering

ENFORCER 4-in-1 HD Rollerball Cameras (TVI, CVI, AHD, Analog)

1x

Rollerball camera

4x

Screws

4x

Screw anchors

1x

DC plug with terminal block

1x

Hex wrench

2x

Rubber plugs*

1x

Small screwdriver *

1x

Manual

Specifications:

Parts List:

311/16” (93mm)

215/16”

Model

EV-Y2201-A2WQ

EV-Y2201-A2GQ

EV-Y2201-AMWQ

EV-Y2201-AMGQ

Housing color

White

Gray

White

Gray

Type

Fixed Rollerb all Camer a

Varifocal Roll er b all Camer a

Formats

TVI (Default) / CVI / AHD / Analog

CMOS

1

/

2.9

" 2MP Sony CMOS

Resolution (HD)

1920x1080

TV Lines (Analog)

1200TVL

3D-NR

Yes

2D-NR

Yes

DWDR

Yes

OSD (On-Screen Display)

Yes

Cable OSD control

Yes

Video output

1.0Vp-p complex video o utput

Megapixels

2MP

Lens

2.8mm ICR

2.8~12mm ICR

Viewing Angle

90°

30°~90°

# of IR LEDs

24

36

IR Range

Up to 50ft (15m)

Up to 100ft (30m)

FPS

30FPS

F Stop

F1.4

F1.4 - F1.6

Minimum
illumination

(IR On)

0Lux

(IR Off)

Color: 0.1Lux/F1.4, B/W: 0.01Lux/F1.4

Gamma correction

0-1

S/N Ratio

50dB

DSS (Digital Slow Shutter)

Yes

Shutter control

Yes

Gain control

Yes

White balance

Auto, Day & Night

Operating voltage

12VDC

(IR On)

150mA

260mA

(IR Off)

80mA

80mA

IP Rating

IP65

Operating temperature

-4°~131° F (-20°~55° C)

Dimensions

311/16"x215/16" (93x75 mm)

43/4"x33/4" (120x95 mm)

Weight

13.1-oz (370g)

1-lb, 10.1-oz (740g)

Overview:

EV-Y2201-A2xQ:

EV-Y2201-AMxQ:

43/4” (120mm)

33/4”

(95mm)

Zoom

Focus

*EV-Y2201-AMxQ only

Current Draw

(75mm)

2 SECO-LARM U.S.A., Inc.

ENFORCER 4-in-1 HD Rollerball Cameras (TVI, CVI, AHD, Analog)

Use the camera within the given temperature

3. Do not subject the camera to strong vibrations.

Before Starting:

1. Run a 12VDC power supply wire and a video

Installation:

6. Put the case over the camera ball and onto the base.

Overview:

Camera ball

Case

Base

Female BNC connector

DC Plug with

DC Jack

OSD Controller

EV-Y2201-A2xQ shown above.

Optional Mounting Brackets:

Wall Mount

EV-DWLWQ

Ceiling Mount

EV-DCLWQ

Conduit Box
EV-DSLWQ

Conduit Drop

EV-DDLWQ

OSD Controller Settings:

To set format via the OSD controller, press
the controller in the direction of the desired
setting, hold for 5 seconds, and release
when the camera restarts.
See chart below.

Direction

Format Sett ing

Up

CVI

Down

TVI

Left

CVBS

Right

AHD

Screws (2 sh own, use all

UP

White models shown, gray mounting brackets also avail abl e.

Important: Do not cut any wires as the warranty will be voided.

4 in installation)

terminal bloc k

1.

and voltage limits.

2. Do not point the camera at the sun. Heat could

damage the camera, even when not in use.

4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.

cable with a male BNC connector through the
wall to where the camera is to be mounted.

2. Loosen the set screws with the included hex

wrench and remove the case from the base.

NOTE: The camera ball is NOT attached to the case

or the base. It sits loose inside the case. Therefore,
be very careful when removing the case from the
base. Do not drop the camera ball.

3. Mount the base to the wall using the four
included mounting screws. If the wall is made
of dry wall, brick, or similar material, it may be
necessary to use the included screw anchors.

4. Run the camera’s BNC and power connectors
through the camera base, and connect to the
video and power wires that were run through
the wall.

SECO-LARM U.S.A., Inc. 3

7. Holding the case loosely on the base, turn the camera
ball to the desired direction. Use the included small
screwdriver to adjust the zoom and focus of the camera
ball if needed, via the holes marked “ZOOM” and
“FOCUS” on the top of the camera ball
(EV-Y2201-AMxQ only).

NOTE: Before securing installation, make sure to check both the day

and night images. Adjust the camera ball in a way so that there
are no objects blocking the camera’s view.

8. Use the OSD controller joystick to adjust camera
settings (see the separate OSD manual).

9. Once the ball is pointing in the desired direction, tighten
the outer case ring to secure the camera in its position.

10. Do a final test of the video camera and monitor.

11. Insert the rubber plugs over the zoom and focus holes
to prevent tampering (EV-Y2201-AMxQ only).

ENFORCER 4-in-1 HD Rollerball Cameras (TVI, CVI, AHD, Analog)

MI_EV-Y2201-AxxQ_161026.docx

PICSN4

Troubleshooting:

The
The image is foggy or washe d

The screen im age is dim
The screen

The screen im age flickers

The screen im age is distorted

The camera case is hot

IR LEDs do not t urn on

WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or elec tric
shock.
Do not cut

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,

will not be

FCC COMPLIANCE STATEMENT

or the

device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
requirements and void user’s authority to operate the device.

NOTICE: The SE CO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM

LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or

in part, without the writt en permission of SECO-LARM.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal

LARM’s obligation is limited to the repair or

This Warranty is void if

misuse or abuse, neglect, repair or alteration,

LARM determines that such equipment

The sole obligation of

’s

al or property

damage of any kind to the pur chaser or anyone else.

SECO-LARM

®

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Website: www.seco-larm.com

Phone: [phone] | [phone]

Email: [e-mail]

• Check that the camera is powered up

screen is black

out at night

• Check that the power supply’s polarity is correct

• Check that the monitor is powered up

• Check that the video cable connecting the camera t o the monitor is

connected properly

• Check that there are no objects very close to the camera

• Check that there are no highly reflect ive objects i n the scene

• Clean the lens using a soft, clean clot h

• Check that the light source is adequate

image has poor contrast

Do not open the case of this d evice, as there are no user-s erviceable components inside.

any wires as the warranty will b e voided.

state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
held responsible for the us e of this product in violati on of any current laws or stat utes.

THIS DEVICE CO MP LIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEP T
ANY INTERFERENCE RECEIVED, INCLUDING INTE RFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifi cations not expressly approv ed by the party responsible for compliance c ould void the user ’s
authority t o operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna

service for three (3) years from the date of sale to the original customer. SECO­replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
damage is caused by or attributed to acts of God, physical or electrical
improper or abnormal usage, or faulty installation, or if for any other reason SECO­is not operating properly as a result of causes other than defects in material and workmanship.
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential person

• Adjust the monitor’s contrast knob

• Change the position of the camera

• Change the position of the camera, check cables and format setting

• Change the position of the camera, check cables and format setting

• Check that the correct power supply is in use

• Check that the correct power supply is in use

reserves the right to chan ge specificat ions without notice. SECO-LARM is also n ot responsibl e for misprints .
Copyright © 2016 SECO-

4 SECO-LARM U.S.A., Inc.