Page 1
4-in-1 HD TVI, CVI, AHD, Analog
• Select between multiple formats:
•
•
•
• 3D-NR (3D Digital Noise Reduction)
•
•
•
Features:
Model #
Lens
Resolution
Voltage
Style
Color
EV-Y1201-A2WQ
2.8mm
1080p
12VDC
Bullet
White
EV-Y1201-AMWQ
2.8~12mm
1080p
12VDC
Bullet
White
EV-Y1201-AMWQ shown
Bullet Cameras
Manual
TVI, CVI, AHD, and Analog
1080p Resolution
ICR Module
Joystick OSD Control
DWDR (Digital Wide Dynamic Range)
Rugged, weatherproof (IP66) construction
Cables concealed in bracket to
prevent tampering
Page 2
ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Camer as
Specifications:
Model
EV-Y1201-A2WQ
EV-Y1201-AMWQ
Type
Fixed Bullet Camera
Varifocal Bull et Camer a
Formats
TVI (Default) / CVI / AHD / Analog
CMOS
1
/
2.9
" 2MP Sony CMOS
Resolution (HD)
1920x1080
TV Lines (Analog)
1200TVL
3D-NR
Yes
2D-NR
Yes
DWDR
Yes
OSD (On-Screen Display)
Yes
Cable OSD control
Yes
Video output
1.0Vp-p Complex video o utput
Megapixels
2MP
Lens
2.8mm ICR
2.8~12mm IC R
Viewing angle
90°
30°~90°
# of IR LEDs
30
3 (IR III)
IR Range
Up to 50ft (15m)
Up to 100ft (30m)
FPS
30FPS
F Stop
F1.4-F1.6
Minimum illumination (IR On)
0Lux
Gamma correction
0-1
S/N Ratio
50dB
DSS (Digital Show Shutter )
Yes
Shutter control
Yes
Gain control
Yes
White balance
Auto, Day & Night
Operating voltage
12VDC
(IR On)
160mA
400mA
(IR Off)
90mA
90mA
IP Rating
IP66
Operating temperature
-4°~131° F (-20°~55° C)
Dimensions
69/16"x29/16" (166x65 mm)
107/16"x31/4" (265x83 mm)
Weight
14.1-oz (400g)
1-lb 10.8-oz (760g)
Dimensions:
1x
Bullet camera
3x/4x*
Screws
3x/4x*
Screw anchors
1x
DC plug with terminal block
1x
Hex wrench
1x
Flathead screwdriver*
1x
Mounting tem plate
1x
Manual
Parts List:
* EV-Y1201-AMWQ Only
EV-Y1201-AMWQ:
EV-Y1201-A2WQ:
415/16" (126mm)
215/16"
(75mm)
69/16" (166mm)
29/16"
(65mm)
31/4"
(83mm)
107/16" (265mm)
65/8" (168mm)
Current draw
2 SECO-LARM U.S.A., Inc.
Page 3
ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Cameras
Overview:
Installation:
Important: Do not cut any wires as the warranty will be voided.
1. Run a 12VDC power supply wir e and a video cable
mounting location is corr ect.
5. Adjust the zoom and focus t o desired settings. See
included mounting screws.
OSD Controller Settings:
To set format via the OSD controller, press the
controller in the directi on of the desired setting,
hold for 5 seconds, and release when the
camera restarts.
See chart below.
Direction
Format Setting
Up
CVI
Down
TVI
Left
CVBS
Right
AHD
UP
DC Plug with
terminal bloc k
DC Jack
Female BNC
Connector
OSD controller
Sunshield screw
Sunshield
Zoom/Focus compartment
Mounting arm
Camera angle
Mounting
EV-Y1201-AMWQ shown above.
Zoom & Focus Adjustment*:
To adjust the Zoom and Focus, open the Zoom/Focus compar tme nt
1. Use the camera wi thin the given temperature
3. Do not subject the camera to s trong vibrations.
Before Starting:
Mounting bas e
*EV-Y1201-AMWQ only.
To adjust the camera an gle an d pos i ti oni n g,
retighten th e screws.
Camera arm posit ion :
Camera Angle and Positioning:
Mounting arm
Camera angle:
Camera angle
(Continued next page)
Zoom
Focus
adjustment screw
using the provided hex wrench.
Once within the compartment, use the provided flathead screwdri ver
to loosen the Zoom and Focus screws to allow f or adjustment.
Focus
To focus in on close objects, push
the focus screw right towards "N".
To focus out on far objects, push
the screw right towards "F".
Zoom
To zoom in, push the zoom screw
left towards "T". To zoom out, push the
screw right towards "W".
adjustment screw
screws
loosen the camera angle adjustment screw
and mountin g arm adjustment screw.
Rotate the camera and position the
mounting arm in the desired position and
and voltage li m its.
2. Do not point the camera at the sun.
with a male BN C connector to the wall or ceiling
where the camera is to be mounted.
2. Temporarily connect the camera to the 12VDC
power supply.
3. Temporarily connect the camera’s female BNC
connector to the video cable’s male BNC connector.
4. While watching the monitor, hold the camera against
the wall or cei ling by hand w here it is to be mounted,
then turn the camera until it is certain that this
SECO-LARM U.S.A., Inc. 3
adjustment screw
4. Do not mount th e camera in areas exposed to radiation,
strong magnetic fields, or strong electric al signals.
"Zoom and Focus Adjustment*". (EV-Y1201-AMWQ
only).
6. Use the OSD controller's joystick t o adjust the camera
7. Use a pencil and the included mou nting template
8. Mount the camera mounting base to the wall using the
settings. See "OSD Contr oller Settings ". (For more
informatio n, see separat e OSD manual).
sticker to mark the mounting location. Disconnect the
12VDC power supply and video cable.
adjustment s crew
Page 4
ENFORCER 4-in-1 HD TVI, CVI, AHD, Analog Bullet Camer as
• Check that the camera is powered up.
• Clean the lens using a soft, clean cloth.
• Adjust the monitor's contrast knob.
The screen image flickers.
• Change the position of the camera, check cables and format setting
The screen image is distorted.
• Change the position of the camera, check cables and format setting
The camera case is hot.
• Check that the correct power supply is in use.
Installation (continued):
®
PICSN4
MI_EV-Y1201-AxWQ_161026.docx
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
will not be
FCC COMPLIAN CE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TW O
MUST ACCEPT
Notice: The changes or modifications not expressly approved by the party responsible for complia nce could void the user’s
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800
Email: sales@seco-larm.com
NOTICE: T he SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copie d, in whole or
in part, without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
the repair or
This Warranty is void if
,
LARM determines that such equipment
The sole obligation of
’s
LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the pur chaser or anyone else.
Troubleshooting:
WARNING: Stop using the camera if you see a mal function such as smoke or unusual heat, as it could cause fire or el ectric
shock.
Do not cut
9. Reconnect the 12VDC power supply a nd video cable.
12. Do a final test of the vide o camera and monitor.
Turn the monitor on and confirm the camera i s sending the proper video signal.
Adjust the camera to the desired angle and position. See "Camera Angle and Positioning" for more information.
• Check that the power supply's polarity is correct.
The screen is blank.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the monitor is
connected properly.
The screen image is dim.
The screen image has poor contrast.
• Check that the light source is adequate.
• Change the position of the camera.
Do not open the case of this device, as there are no user-serviceable components inside.
any wires as the warranty will b e voided.
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
held responsible for the us e of this product in violation of any curr ent laws or statutes.
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THA T MAY CAUSE UNDESIRED OPERATION.
authority t o operate the e quipment.
requirements and void us er’s authorit y to operate the device.
service for three (3) years from the dat e of sale to the ori ginal customer. SECO-LARM’s obligation is limited to
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration
improper or abnormal usage, or faulty installation, or if for any other reason SECOis not operating properly as a result of causes other than defects in material and workmanship.
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM
option. In no event shall SECO-
reserves the right to change specific ations without notice. SECO-LARM is also not responsible for misprints.
Copyright © 2016 SECO-
4 SECO-LARM U.S.A., Inc.
Loading...