Page 1
®
Wall-Plate Cameras
Manual
Model # Lens Image Sensor Resolution Video Output Format
EV-5105-N1SQ
EV-T5105-N2SQ 720p HD-TVI
Features:
1
2.4mm Wide angle lens
Weatherproof construction
Vandal-resistant design
Adjustable mounting angle
/
" 1.3MP Sony STARVIS CMOS
3.2
2.4mm
1
/
" 1.3MP Sony
3.2
STARVIS CMOS
1000TVL NTSC
Includes: 1 camera, 1 single-gang plate,
1 slimline plate, and angled mounting rings
2DNR (2D Digital Noise Reduction)
WDR (Wide Dynamic Range)
12VDC Operating voltage
Page 2
ENFORCER Wall-Plate Cameras
A
A
(
(
Specifications:
Model EV-5105-N1SQ EV-T5105-N2SQ
Type Wall-plate camera
Plate type 1 Single-gang, 1 slimline
Image sensor
Resolution 1000 TV Lines 720p
Video output format NTSC HD-TVI
Effective pixels 1280x960
2DNR Yes
WDR Yes
960H* Yes No
Scanning system 2:1 Interface
Sync Internal
Video output 1.0Vp-p Composite video, 75Ω
Lens 2.4mm
Viewing angle 150°
FPS 30FPS
F Stop 2.2
Minimum illumination 0.001Lux
Gamma correction 0.45
S/N Ratio 120dB 50dB
Gain control Auto
Operating voltage 12VDC
Current draw 80mA 90mA
IP Rating IP67 IP65
Operating temperature -22°~176° F (-30°~80° C)
Dimensions
*In order to take full advantage of 960H resolution, the camera must be used with a 960H DVR
Parts List:
1x Camera 1x Angled rubber ring (EV-5105-N1SQ) 1x Slimline plate
2x Mounting screws 1x
1x
Camera 1
Single-gang plate 23/4"x41/2" (70x114 mm)
Slimline plate 11/2"x41/2" (38x114 mm)
luminum hex nut 2x Angled aluminum rings (EV-T5105-N2SQ) 1x Manual
1
/8"x11/8"x11/2" (28x28x38 mm) 11/8"x11/8"x17/8" (28x28x48 mm)
ngled aluminum ring (EV-5105-N1SQ) 1x Single-gang plate
1
/
" 1.3MP Sony STARVIS CMOS
3.2
Dimensions:
Single-gang plate
23/4" (70mm)
41/2"
(114mm)
Slimline plate
11/2" (38mm)
11/8"
(28mm)
EV-5105-N1SQ
Camera body
11/2" (38mm)
(22mm)
7
/8"
7
22mm)
/8"
EV-T5105-N2SQ
Camera body
17/8" (48mm)
11/8"
(28mm)
2 SECO-LARM U.S.A., Inc.
11/4"
(32mm)
15
24mm)
/16"
Page 3
ENFORCER Wall-Plate Cameras
A
A
A
Before Starting:
1. Read this manual carefully and keep it for future
reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
5. Do not open or disassemble the camera. There
are no user-serviceable parts inside.
6. Do not subject the camera to extreme shock.
Overview:
Plate
Camera
ngled rubber/aluminum ring
ngled aluminum ring
luminum hex nut
NOTE: Ensure that the angled aluminum ring is installed next to the aluminum hex nut in all
applicable mounting installations.
When installing the camera, ensure that the white mark behind the lens is at the top.
DC Jack
Note polarity when connecting
Female BNC connector
IMPORTANT: Do not cut the video or power wires
as warranty will be voided.
Mounting the Camera to the Plate: Mounting Options:
With Plate and Back Box (suggested):
Back
box
To mount the camera to the plate, position the
angled rings behind the plate and twist the aluminum
hex nut on to secure the plate to the camera.
Mount directly to the back box (not included).
Plate, no Back Box:
If an object installed next to the camera on the wall
is blocking the field of vision, the angled rings may
be installed in front of the wall plate to move the
field of vision forward.
Changing the Mounting Angle:
Install one of the angled rings on the front of the plate
so that the camera is tilted (approximately 20°).
Drill a hole in the wall according to the diameter of
the camera body. Mount the plate directly to the wall.
No Plate and no Back Box:
Min. wall thickness: 5/16" (8mm)
Max. wall thickness:
EV-5105-N1SQ:
3
/4" (20mm)
EV-T5105-N2SQ:
5
1
/16" (34mm)
Drill a hole in the wall according to the diameter of
the camera body. If mounting to a thick surface, it
may not be necessary to use the angled rings.
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Wall-Plate Cameras
(
Troubleshooting:
Check that the camera is powered up
Check that the power supply's polarity is correct
The screen is blank
The screen image is dim
The screen image has poor contrast
The screen image flickers
The screen image is distorted
The camera case is hot
Check that the monitor is powered up
Check that the video cable connecting the camera to the
monitor is connected properly
Clean the lens using a soft, clean cloth
Adjust the monitor's contrast knob
Change the position of the camera
Change the position of the camera
Change the position of the camera
Check that the correct power supply is in use
Also Available from SECO-LARM®:
4-in-1 HD Motorized
Rollerball Camera
EV-Y2201-ANWQ EV-Y1201-ANWQ EV-Y2201-ANWAQ
4-in-1 HD Motorized
Bullet Camera
4-in-1 HD Motorized
Vandal Dome Camera
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be
held responsible for the use of this product in violation of any current laws or statutes.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
WARRANTY:
service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2017 SECO-LARM U.S.A., Inc. All
rights reserved.
SECO-LARM
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
®
U.S.A., Inc.
Order Part# 764-100-7%
949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
MI_EV-x5105-NxSQ_170816.docx
4 SECO-LARM U.S.A., Inc.
®
PITSW1
Loading...