Page 1
EV-N4206-2S4Q
IP Corner-Mount Camera
Manual
Features:
1/
2.8
H.265, H.264/MJPEG, Tri-stream IP Camera
Max. 30FPS/Full HD (1920x1080)
Remote access via web browser
Network Bandwidth Control
Event Alarm, E-mail, FTP Function
ONVIF Profile S
" 2MP Sony STARVIS™ CMOS
30 Covert IR LEDs for discreet monitoring
in the dark
True Day & Night function with
ICR mechanism
Vandal-resistant metal front panel
3DNR & WDR
12VDC, PoE (IEEE802.3af)
Page 2
ENFORCER IP Corner-Mount Camera
A
A
Specifications:
Model EV-N4206-2S4Q
Type Corner-Mount Camera
Sensor
Video encoding H.265 ,H.264, MJPEG
Resolution 1920x1080
DNR
WDR Yes, 120dB
Scanning system Progressive 1080p
# of IR LEDs 30 (940nm)
Lens 2.8mm
Viewing angle 135°
Minimum illumination 0.01 Lux (F/1.6)
Gamma correction 0.45
S/N ratio 50dB
Gain control
White balance
Operating voltage 12VDC, PoE 802.3af
Current draw (IR Off) 150mA max.
IP Rating IP65
Operating temperature 14°~122° F (-10°~50° C)
Dimensions 7
Weight 13.75-oz (390g)
2DNR Yes
3DNR Yes
1
/
" 2MP Sony STARVIS™ CMOS
2.8
1
/2" x51/2"x111/16" (190x140x43 mm)
uto
uto
Parts List:
1x Camera 1x Camera cover 1x CD 4x Mounting screws
1x Pigtail connector 3x Security screws 1x Security wrench 1x Manual
Dimensions:
71/
" (190mm)
2
51/
"
2
(140mm)
111/
16
(43mm)
2 SECO-LARM U.S.A., Inc.
"
Page 3
Overview:
ENFORCER IP Corner-Mount Camera
DC jack
Pigtail connector
Mounting screws
Security screws
RJ45 jack
BNC jack
Camera cover
Important: Do not cut DC jack or RJ45 jack as warranty will be voided.
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
Installation:
1. Use the included security wrench to loosen the screws
and remove the camera cover from the camera.
2. Run a 12VDC power supply wire and cable with an
RJ45 jack through the wall at the corner where the
camera is to be mounted.
3. Execute "IP Manager" on the PC.
4. Press the "Find" button. IP cameras connected to the
same router will be searched and listed. This may take
several seconds. Default IP address is 192.168.1.30.
5. Right-click the desired product, and press "IP Change".
6. Use web port number 80. This is an internal port.
7. IP address: You may use Dynamic IP or you may set
Static IP as below:
Typical IP setting is as follows.
IP address.: 192.168.0.10 (you can change the last column)
Netmask: 255.255.255.0
Gateway: 192.168.0.1
DNS1/2: You can copy the PC's network properties.
This is for internet environments.
3 SECO-LARM U.S.A., Inc
4. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.
5. Do not open or disassemble the camera. There are no
field-serviceable parts inside.
6. Do not drop the camera or subject it to
strong vibrations.
8. Input "admin" for User ID and password
NOTE: It is recommended that you change the default
password.
9. Press "Change" to save settings and allow 10s for
changes to appear.
10. Right-click the desired device and click
"Open Web Page".
11. Enter Username / Password.
12. Click "Live" on top right of the screen.
13. Click yes for "ActiveX Control".
14. After the installation of Active X, you will be able to view
the live feed only with Internet Explorer.
15. Visit http://www.seco-larm.com/EV-N4206-2S4Q
for the Web Admin Manual.
Page 4
ENFORCER IP Corner-Mount Camera
q
Troubleshooting:
The screen is blank.
The screen image is dim
The screen image has poor contrast.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
IR LEDs do not turn on.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state,
and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held
responsible for the use of this product in violation of any current laws or statutes.
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock.
Do not open the case of this device, as there are no user-serviceable components inside.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
uirements and void user’s authority to operate the device.
re
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Change the position of the camera.
Change the position of the camera.
Check that the correct power supply is in use.
Check that the correct power supply is in use.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2019 SECO-LARM U.S.A., Inc. All
rights reserved.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
MI_EV-N4206-2S4Q_190923.docx
4 SECO-LARM U.S.A., Inc.
PIKSR1
Loading...