Page 1
IP 5MP Full-Color
H.265, H.264
, and MJPEG
ONVIF®
is a trademark of ONVIF, Inc
Turret Camera
with WDR
EV-N2506-2W4WLQ
Installation Manual
Features AI Functions
• 1/
" 5MP SmartSens CMOS Sensor • Human and Vehicle Detection
2.7
• 30FPS@ 5MP (2880x1620) • Perimeter Intrusion Detection
• 2.8mm Lens • Line Crossing Detection
• Tri-stream encoding: • Stationary Object Detection
• Cross Counting
• True Wide Dynamic Range (WDR) • Heat Map
• Digital Noise Reduction (3DNR) • Crowd Density Detection
• True Day & Night function with ICR module
• ICR sensitivity adjustment
• Corridor mode
• IP66 Weatherproof
• IR Range 98' (30m)
• White LED 120°
• Smart IRs adjust IR strength to conditions
• MicroSD slot (512GB max)
• PoE (IEEE802.3af), 12VDC
• ONVIF® Profile G, S, and T conformant
• Operating temperature: -40°~131°F
(-40°~55°C)
• Queue Length Detection
• Face Detection
For the full Web Administration manual,
download from the camera’s product
page on www.seco-larm.com.
Page 2
IP 5MP Full-Color Turret Camera with WDR
1x Camera
3x
Mounting Screws
1x
Weatherproof Connector
1x
Manual
1x
Mounting Template
(90mm)
Parts List
Specifications
Type Turret, White LEDs
Sensor
Video encoding H.265/H.264/MJPEG
Megapixels 5MP
Resolution 2880x1620
Backlight Disable (Default), Back Light, HLC, WDR
DNR
AI functions
# of LEDs 2pcs (850nm), 2pcs (120° White LEDs)
Lens 2.8mm
Viewing angle 133°
Minimum illumination Color: 0.1 lux at F1.2 (AGC on), 0Lux with IR on
F Stop 1.6
Gamma correction Auto
S/N ratio 39dB
Gain control Auto
White balance Auto
Operating voltage 12VDC, PoE (IEEE802.3af Class 0)
Current draw (IR Off) 80mA max.
IP Rating IP66
Operating temperature -40°~131° F (-40°~55° C)
Dimensions ø315/16"x39/16" (ø100x90 mm)
Weight 13.05-oz (370g)
On-board storage Built-in memory card slot, Supports MicroSD/SDHC/SDXC up to 512GB
2DNR N/A
3DNR Yes
Human and Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection,
Stationary Object Detection, Cross Counting, Heat Map, Crowd Density Detection,
1
/
" 5MP SmartSens CMOS
2.7
Queue Length Detection, Face Detection
Overview
2 SECO-LARM U.S.A., Inc.
ø315/16" (ø100mm)
39/16"
Page 3
IP 5MP Full-Color Turret Camera with WDR
DJ Jack
RJ45 Ethernet Jack
Reset button
Overview (Continued)
Micro SD / Reset button compartment
Micro SD Card slot
Top of camera
IMPORTANT NOTES
• Do not cut DC jack or RJ45 jack as warranty will be voided.
• Do not open camera case, no serviceable parts.
Before Starting
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not mount in areas exposed to radiation, strong
magnetic fields, or strong electrical signals.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not open or disassemble the camera. There are
no field-serviceable parts inside.
6. Do not drop the camera or subject it to strong
vibrations.
Installation
1. Run a 12VDC power supply wire and cable with
an RJ45 jack through the wall at the location
where the camera is to be mounted. The 12VDC
power supply wire is not required if using PoE.
2. Install and Execute "Device Config Tool" on a
computer connected to the same network as the
camera.
3. Press the "Search" button. This will search for IP
cameras connected to the same router on the
network. It may take several seconds to
complete. Default IP address is 192.168.1.168.
4. Once the search is complete, click on the camera
IP or type the IP address manually using Internet
Explorer.
5. IP Address: The camera may use Dynamic or
Static IP addressing. An example of a typical
static IP setting is as follows:
IP Address: 192.168.0.10 (you can change the
last column)
NOTE: For the full Web Admin manual, download from the camera’s product page on www.seco-larm.com.
SECO-LARM U.S.A., Inc. 3
Netmask: 255.255.255.0
Gateway: 192.168.0.1
DNS1/2: You can copy the PC’s network
properties. This is for an internet
environment.
6. Input "admin" for user ID and password. If this is
the user's first time logging into the camera, the
user will be prompted for a new password.
NOTE: If the password is unknown, hold the
RESET button located on the camera for
about 10 seconds and reload "Device
Config Tool".
7. In order to access the camera web interface, the
user will be prompted to download and install the
Active-X web plugin.
8. Once installed, the user will be able to view live
camera video and modify necessary
configurations.
Page 4
IP 5MP Full-Color Turret Camera with WDR
Profile 1: Display Color 24/7
When using this profile, the white LED will only be activated during the nighttime for color display,
and the white LED cannot be used as a deterrence. If the IPC is connected to an ENFORCER NVR
via the Private Protocol, please use the NVR interface to adjust the settings.
Step 1 – Default All Settings
1. Go to Remote Setting > System > Maintenance > Load Default.
2. Select All at the top of the menu.
3. Click Save and follow the instructions on the screen to complete the process.
Step 2 – Access Image Control
1. Go to Remote Setting > Channel > Image Control.
2. Set Image Setting to Full Color Mode.
3. Set White Light to Automatic mode or Schedule.
NOTES
• In Automatic Mode, the white LED will be activated when the surrounding environment
becomes dark. This mode is recommended for outdoor use.
• In Schedule Mode, the white LED will be activated on a set schedule. This mode is
recommended for indoor use.
4 SECO-LARM U.S.A., Inc.
Page 5
IP 5MP Full-Color Turret Camera with WDR
Profile 2: White LED as Deterrence
When using this profile, the camera will perform as a regular IP 5MP 2.8mm Turret. The white LED
will only be activated when an alarm event occurs. Below is a sample application for general use
and users should adjust any of the settings depending on their own use case.
Step 1 – Default all settings
1. Go to Remote Setting > System > Maintenance > Load Default.
2. Check every box in this menu.
3. Click Save and follow the instructions on the screen to complete the process.
Step 2 – Turn Off Motion Detection
Go to Remote Setting > Event > Setup > Motion > Enable: OFF.
SECO-LARM U.S.A., Inc. 5
Page 6
IP 5MP Full-Color Turret Camera with WDR
Profile 2: White LED as Deterrence (Continued)
Step 3 – Set a Detection Mode
To set a Detection Mode, go to Remote Setting > AI > Setup > PD&VD.
NOTE: Pedestrian & Vehicle Detection is recommended for the best performance. The instructions
for AI Settings are available in the web administration manual.
Step 4 – Alarm setting for the corresponding AI function
1. Go to Remote Setting > AI > Alarm > PD&VD.
2. Turn on Deterrent.
NOTE: Use Schedule if users want this function to be active only during the nighttime.
6 SECO-LARM U.S.A., Inc.
Page 7
IP 5MP Full-Color Turret Camera with WDR
Profile 2: White LED as Deterrence (Continued)
Step 5 – Change image Setting to Day/Night Mode
1. To change the setting to Day and Night mode go to Remote Setting > Channel > Image
Control.
2. Set Image Setting to Day/Night Mode.
Step 6 – Turn on Deterrence
1. Go to Remote Setting > Event > Setup > Deterrence.
2. Turn Light On.
3. Set Duration between 5~180 seconds (default: 5).
4. Turn Color Image On to view video display in color; Off to view in black and white.
5. Choose Deterrence Mode: Light Warning or Light Strobe.
6. Adjust Sensitivity 1~8 (default: 4).
SECO-LARM U.S.A., Inc. 7
Page 8
IP 5MP Full-Color Turret Camera with WDR
FCC COMPLIANCE STATEMENT
THIS DEVICE MAY
ICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
ed. Any change to the antenna
IMPORTANT
: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local l
aws and statutes related to
IMPORTANT:
Users and installers of this product are responsible for ensuring that the installation and configuration of this product com
plies with all national, state,
California Proposition 65 Warning:
These products may contain chemicals which are known to the Sta te of California to cause cancer and birth defe
cts or other
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship wh
ile used in normal service for
three (3) years
from the date of
id, to
to acts of God, physical or electrical misuse or abuse, neglec t, repair or alteration, improper
such equipment is not operating properly as a result of causes other
exclusive remedy, shall be limited to the replacement or repair
LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any
NOTICE:
The SECO
-
LARM policy is one of continual development and improvement. For th
at reason, SECO LARM reserves the right to change specifications without
16842 Millikan Avenue, Irvine, CA 92606
Website:
www.seco
-
larm.com
MI_EV-N2506-2W4WLQ_221117.docx
Troubleshooting
The screen is blank
The screen image is dim
The screen image has poor
contrast
The screen image flickers
The screen image is distorted
The camera case is hot
• Check that the camera is powered up.
• Check that the power supply’s polarity is correct.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the monitor is
connected properly.
• Clean the lens using a soft, clean cloth.
• Check that the light source is adequate.
• Adjust the monitor’s contrast knob.
• Change the position of the camera.
• Change the position of the camera.
• Change the position of the camera.
• Check that the correct power supply is in use.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)
NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEV
CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitt
or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
reproductive harm. For more information, go to www.P65Warnings.ca.gov.
sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepa
SECO-LARM. This Warranty is void if damage is caused by or attributed
or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that
than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s
only, at SECO-LARM’s option. In no event shall SECOkind to the purchaser or anyone else.
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023
SECO-LARM U.S.A., Inc. All rights reserved.
SECO-LARM
Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
®
U.S.A., Inc.
PICRN3
Loading...