Seco-Larm EV-N2506-2W4Q Installation Manual

Manual

EV-N2506-2W4Q

IP Fixed Turret Camera

Features:

1/

" 5MP SMARTSENS CMOS

2.7

 H.265/H.264, Tri-stream IP Camera
 12VDC, PoE 802.3af
 True Day & Night function with ICR

mechanism

 Max. 20FPS/5MP, 1440p (2592x1944)
 3DNR
 Weather-resistant (IP66)
 ONVIF Profile S, Profile G

®

ENFORCER IP Fixed Turret Camera

Specifications

:

1x Camera

1x CD 3x

Mounting screws

Sensor

1/

" 5MP S

MARTSENS

CMOS

Video encoding

H.265/H.264

Megapixels

5MP

Resolution

1440p,

2592x1944

2DNR N/A

3DNR Yes Scanning system

Progressive 1080p

#

of IR LEDs

2pcs (850nm)

Lens 2.8mm

Viewing angle

131° Minimum illumination

0.05 Lux

F Stop

1.2 Gamma correction

Auto S/N Ratio N/A Gain control

Auto

White balance

Auto

Operating voltage

12VDC, PoE

802.3af

Current draw (IR Off)

80mA max.

IP

Rating

IP66 Operating temperature

-22°~131° F (

-

30°~55° C)

Dimensions

ø315/16" x39/16" (ø1

00x90 mm)

Weight

13.4-oz (370g)

ø315/16" (ø100mm)

39/16"

Type Fixed Turret Camera

2.7

DNR

Parts List:

1x Manual 1x Security wrench 1x DC Plug w/ terminal block

Dimensions:

(90mm)

2 SECO-LARM U.S.A., Inc.

ENFORCER IP Fixed Turret Camera

RJ45 Ethernet Jack

DC Jack

terminal block

Micro SD

Reset

Micro SD / Reset button

1. Please read this manual carefully and keep it for

4. Do not mount the camera in areas exposed to

1. Run a 12VDC power supply wire and cable with

.

Static IP addressing. An example of a typical static

Netmask: 255.255.255.0

user will be prompted to download and install the

Overview:

Card slot

Top of camera

button

Before Starting:

future reference.

2. Use the camera within given temperature and
electrical limits.

3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.

compartment

DC Plug with

radiation, strong magnetic fields, or strong
electrical signals.

5. Do not open or disassemble the camera. There
are no field-serviceable parts inside.

6. Do not drop the camera or subject it to strong
vibrations.

Installation:

an RJ45 jack through the wall at the location
where the camera is to be mounted. The 12VDC
power supply wire is not required if using PoE.

2. Install and Execute "Device Config Tool" on a
computer connected to the same network as the
camera.

3. Press the "Search" button. This will search for IP
cameras connected to the same router on the
network. It may take several seconds to complete
Default IP address is 192.168.1.168.

4. Once the search is complete, click on the camera
IP or type the IP address manually using Internet
Explorer.

5. IP Address: The camera may use Dynamic or

IP setting is as follows:
IP Address: 192.168.0.10 (you can change the

last column)

NOTE: For the full Web Admin manual, download from the camera’s product page on www.seco-larm.com.

SECO-LARM U.S.A., Inc. 3

Gateway: 192.168.0.1
DNS1/2: You can copy the PC’s network

properties. This is for an internet
environment.

6. Input "admin" for user ID and password. If this is
the user's first time logging into the camera, the
user will be prompted for a new password.
NOTE: If the password is unknown, hold the

RESET button located on the camera for
about 10 seconds and reload "Device
Config Tool".

7. In order to access the camera web interface, the

Active-X web plugin.

8. Once installed, the user will be able to view live
camera video and modify necessary
configurations.

ENFORCER IP Fixed Turret Camera

The screen image is dim.

The screen

image has poor contrast.

The screen image flickers.

The screen image is distorted.

The camera case is hot.

16842 Millikan Avenue, Irvine, CA 92606

Website:

www.seco

-

larm.com

LARM reserves

rademarks are the

Inc. All rights

used in normal

ed to the repair or

This Warranty is void if

ation, improper

LARM determines that such equipment is not

LARM

In no event

LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind

installers of this product are responsible for ensuring this product complies with all national, state,

will not be held

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

DEVICE MUST ACCEPT

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device

is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements

WARNING:

Troubleshooting:

The screen is blank.

 Check that the camera is powered up.
 Check that the power supply’s polarity is correct.
 Check that the monitor is powered up.
 Check that the video cable connecting the camera to the

monitor is connected properly.

 Clean the lens using a soft, clean cloth.
 Check that the light source is adequate.

 Adjust the monitor’s contrast knob.
 Change the position of the camera.

 Change the position of the camera.

 Change the position of the camera.

 Check that the correct power supply is in use.

electric shock. Do not open the case of this device, as there are no user-serviceable components inside.

IMPORTANT: Users and

and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM
responsible for the use of this product in violation of any current laws or statutes.

FCC COMPLIANCE STATEMENT

Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

authority to operate the equipment.

and void user’s authority to operate the device.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while

service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limit
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alter
or abnormal usage, or faulty installation, or if for any other reason SECO­operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO­and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option.
shall SECO­to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO­the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All t
property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2020 SECO-LARM U.S.A.,
reserved.

®

SECO-LARM

U.S.A., Inc.

Phone: [phone] | [phone] Email: [e-mail]

MI_EV-N2506-2W4Q_200803.docx

4 SECO-LARM U.S.A., Inc.

PICRN3