Page 1
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
Covert PIR Camera
Manual
• Camera is covertly hidden in a
•
1
/3” Sony CCD
Programmable
Motion-Activated LED
Covert
IR LEDs
EV-6680-N3WQ
NTSC
Yes
No
EV-6680-P3WQ
PAL
Yes
No
EV-6681-N3WQ
NTSC
No
Yes
EV-6681-P3WQ
PAL
No
Yes
EV-6680 Series
EV-6681 Series
human eye.
Motion-activated LED
programmable from the
OSD menu, simulating a
real PIR sensor.
(Non-functioning PIR)
Invisible 94 0nm IR
LEDs provid e infrared
light for the camera but
are invisible to the
Model Format
non-functioning PIR sensor housing
• OSD (On-Screen Display) for
programming special features
• 3.7mm Lens
• 700 TV Lines, 960H high resolution
Page 2
ENFORCER Covert PIR Camer a
13/8”
EV-6680-N3WQ
EV-6680-P3WQ
EV-6681-N3WQ
EV-6681-P3WQ
Type
Covert PIR Camera
CCD 1/3” Sony Super HAD II
1
/3” Sony EXview HAD II
Resolution
700 TV Lines
Video output form at
NTSC
PAL
NTSC
PAL
Effective pixel s
976x494 pixels
976x582 pixels
976x494 pixels
976x582 pixels
DNR (2D-NR)
Yes
DWDR
Yes
OSD Control
Yes
960H1
Yes
Scanning system
2:1 Interlac e
Sync
Internal
Video output
1.0Vp-p Composite video, 75Ω
Lens
3.7mm
# of IR LEDs
N/A
18 (940nm)
IR Range
N/A
50ft (15m)
Minimum
illumination
LEDs OFF
0.1 Lux
LEDs ON
N/A
0 Lux
Gamma correcti o n
0.45
S/N Ratio
>48dB
AES (Auto Elect ric
1/60~1/100, 000 s
AES (Auto Elect ric
1/50~1/100, 000 s
AES (Auto Elect ric
1/60~1/100, 000 s
AES (Auto Elect ric
1/50~1/100, 000 s
Gain control
Auto
Operating v oltage
12VDC
Current
draw
LEDs OFF
70mA
LEDs ON
80mA2
230mA
Operating temperature
14°~122° F (-10°~50° C)
Dimensions
41/8”x23/8”x13/8” (105x60x35 mm)
Cable length
21” (55cm)
Weight
3.9-oz (110g)
With PIR function LED ON
23/8”
(60mm)
Specifications:
Parts List:
1x Camera 2x Mounting screws 1x Mounting bracket 1x DC Plug w/ terminal block
1x Manual 2x Screw anchors 1x Mounting bracket ball
2”
(52mm)
41/8”
Dimensions:
Front View
Side View
Shutter control
Shutter),
Shutter),
Shutter),
Shutter),
1
In order to take full advantage of 960H resolution, the camera m ust be used wit h a 960H DVR.
2
(35mm)
(105mm)
2 SECO-LARM U.S.A., Inc.
Page 3
Overview:
Important:
connector as this will void t he warranty.
Female BNC connector
DC Plug with terminal block
Camera
Pinhole
DC Jack
Mounting bracket
Slide camera
Before Starting:
1. Please read this manual carefully and keep
use.
5. Do not mount the camera in areas exposed
Installation:
1. Run a 12VDC power supply wire and a
6. EV-6680 Series Only: The motion-activated
In-line OSD joystick
Mounting bracket ball
downward onto
the mounting
bracket
ENFORCER Covert PIR Camer a
Do not cut the DC jack or the fem ale BNC
it for future reference.
2. Use the camera within given temperature
and electrical limits.
3. Do not mount the camera where it is
exposed to rain or other moisture, or in
humid or dusty places.
4. Do not point the camera at the sun. Heat
could damage the camera, even when not in
video cable with a male BNC connector
through the wall to where the camera will be
mounted.
2. Connect the camera’s video and power
cables.
3. Temporarily mount the camera to test its
function and display.
4. Do a preliminary test of the camera to
ensure it will work properly.
5. Program the camera if needed via the
attached OSD joystick. For OSD
programming, see separate OSD
programming manual.
to radiation, strong magnetic fields, or strong
electrical signals.
6. Do not open or disassemble the camera.
There are no user-serviceable parts inside.
7. Do not drop the camera or subject it to
strong vibrations.
8. For OSD programming, see separate OSD
programming manual.
LED is tied to the motion detection feature in
the OSD. To turn this feature ON or OFF,
see page 9 of the OSD manual.
7. Partially screw a screw into the wall where
the top of the bracket should go. Slide the
bracket onto the screw. Finish securing the
top of the bracket to the wall.
8. Secure the bottom of the bracket to the wall.
9. Attach the mounting bracket ball to the
mounting bracket by gently pushing the ball
into the bracket.
10. Attach the camera to the assembled bracket
by sliding the camera downward.
11. Do a final test of the video camera and
monitor.
SECO-LARM U.S.A., Inc. 3
Page 4
ENFORCER Covert PIR Camer a
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
or in part, without the written permission of SECO-LARM.
WARRANTY:
LARM product is warranted against defects in material and workmanship while used in
LARM and the purchaser’s exc lusive remedy, shall be limited to t he replacement or repair only, at
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA, 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800
Email: sales@seco-larm.com
Troubleshooting:
FCC COMPLIANCE STATEMENT:
Information to the user: This equipment has been tested and found to comply
pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
own expense.
WARNING:
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or
electric s hock. Do not open the case of thi s device, as there are no user-serviceable c omponents inside.
IMPORTANT:
Users and installers of this product are responsible for ensuring this product complies with all national,
held responsible for the use of the product in violation of any current laws or statutes.
The screen is blank.
The screen image is dim.
• Check that the camera is powered up.
• Check that the power supply’s polarity is correct.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the
monitor is connected properly.
• Clean the lens using a soft, clean cloth.
• Check that the light source is adequate.
• Check that the IR LEDs turn on when light is low
(EV-6681-N3WQ and EV-6681-P3WQ only)
The screen image has poor contrast.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
state, and local laws and statues related to monitoring and recording audio and video signals. SECO-LARM will not be
with the limits for a class B digital device,
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her
This SECO-
normal service for a period of two (2) years from the date of sale to the original customer. SECO-LARM’s ob ligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The
sole obligation of SECOSECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damage of any kind to the purchaser or anyone else.
• Adjust the monitor’s contrast knob.
• Change the position of the camera.
• Change the position of the camera.
• Change the position of the camera.
• Check that the correct power supply is in use.
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not res ponsible for misprints or typographical er rors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
4 SECO-LARM U.S.A., Inc.
MiEV-668x-N3WQ_1402.docx
PICVN3
Loading...