Seco-Larm EV-6640-N3WQ User Manual

Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS -compliant products.
Flush-Mount UFO Camera
Manual
Lens rotates to nearly any angle for
Low-profile design blends in with
nearly any décor
1
/3” Sony Super HAD II CCD
3.7mm Pinhole lens Metal case for vandal resistance
2D-NR (2D Digital Noise Reduction)
cleans and sharpens images by reducing camera noise
DWDR (Digital Wide Dynamic Range)
captures a clean, high-resolution image even in strong backlight.
Small size protrudes only 1” (26mm)
EV-6640-N3WQ (NTSC)
EV-6640-P3WQ (PAL)
ENFORCER Flush-Mount UFO Camera
EV-6640-N3WQ
EV-6640-P3WQ
Type
Flush-Mount UFO Camera
CCD
1
/3” Sony Super HAD II
Resolution
700 TVL
Video output format
NTSC
PAL
Effective pixels
976x492 pixels
976x582 pixels
DNR (2D-NR)
Yes
DWDR
Yes
960H*
Yes
Scanning system
2:1 Interlace
Sync
Internal
Video output
1.0Vp-p Composite video, 75Ω
Lens
3.7mm
Minimum illumination
0.05 Lux
Gamma correction
0.45
S/N Ratio
>48dB
Shutter control
AES (Auto Electronic Shutter), 1/60~1/100,000 s
Gain control
Auto
White balance
Auto
Operating voltage
12VDC
Current draw
130mA ±10mA
Operating temperature
-4°~122° F (-20°~50° C)
Dimensions
3”x3”x1” (77x77x26 mm) (Protruding from wall)
Weight
3.6-oz (103g)
*In order to take full advantage of 960H resolution, the camera must be used with a 960H DVR.
Specifications:
Parts List:
1x Camera 1x Flange
1x Base 1x Ring bracket
3x Mounting screws 1x Manual
1x DC Plug with
terminal block
Dimensions:
Optional Surface-Mount Bracket (Sold separately):
EV-6640SWQ
Surface-mounting allows for a quick and easy installation while maintaining a low-profile appearance.
Diameter: 25/16” (109mm) Height (with camera): 23/8 (60mm)
Flange
Camera ball
Base
Assembled camera
3”
(77mm)
115/16”
(49mm)
213/16”
(72mm)
21/4”
(56mm)
1”
(26mm)
3” (77mm)
2 SECO-LARM U.S.A., Inc.
ENFORCER Flush-Mount UFO Camera
Overview:
Standard installation
Surface-mount installation – Requires the EV-6640SWQ (Sold Separately)
Flange
Camera
Ball
Mounting
screws x3
Ring bracket
(inside ceiling/wall)
Wall
or
Ceiling
Base
Surface-mount
bracket
Run the power and
video cables through
the wall or on surface
Wall
or
Ceiling
Flange
Camera
Ball
Mounting
screws x3
Installation:
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not mount the camera where it is exposed to rain
or other moisture, or in humid or dusty places.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong electrical signals.
6. Do not drop the camera or subject it to strong vibrations.
1. Run a 12VDC power supply wire and a video cable with
a male BNC connector to the wall or ceiling where the camera is to be mounted.
2. Temporarily connect the camera to the 12VDC
power supply.
3. Temporarily connect the camera’s female BNC
connector to the video cable’s male BNC connector.
4. While watching the monitor, hold the camera against
the wall or ceiling by hand where it is to be mounted, then turn the camera until it is certain that this mounting location is correct. Use a pencil to mark the location.
5. Disconnect the 12VDC power supply and video cable.
6. Drill a 2
1
/16” (52m) hole in the ceiling or wall where the
camera is to be mounted.
7. Twist the flange off the base and remove the
camera ball.
8. Place the ring bracket behind the hole.
NOTE: Ring bracket is not necessary if mounting directly to wall.
9. Push the base into the hole, and secure to the ring
bracket using the three supplied marking screws.
10. Run the power supply and video cable through the wall
or ceiling to the hole, and through the bracket and base. Connect to the camera’s power and video connectors.
11. Hold the ball in the base, and secure with the flange.
Secure the flange partially, leaving room to adjust the angle of the lens.
12. Apply the power to the camera. Watch the monitor
and adjust the angle of the lens.
13. Secure the camera by tightening the flange.
14. Do a final test of the video camera and monitor.
SECO-LARM U.S.A., Inc. 3
ENFORCER Flush-Mount UFO Camera
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or
electric shock. Do not open the case of this device, as there are no field-serviceable components inside.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
The screen is blank.
Check that the camera is powered up. Check that the power supply’s polarity is correct Check that the monitor is powered up. Check that the video cable connecting the
camera to the monitor is connected properly.
The screen image is dim.
Clean the lens using a soft, clean cloth. Check that the light source is adequate.
The screen image has poor contrast.
Adjust the monitor’s contrast knob. Change the position of the camera.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
Troubleshooting:
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA, 92606
Website: www.seco-larm.com
Tel: (949) 261-2999 | (800) 662-0800
Email: sales@seco-larm.com
MiUFO_Camera_1311_700TVL_NoWP.docx
PICSN4
4 SECO-LARM U.S.A., Inc.
Loading...