Seco-Larm EV-5105-N1SQ User Manual

Manual

Wall-Plate Camera

EV-5105-N1SQ (NTSC)

Includes 1 single-gang
and 1 slimline plate

EV-5105-P1SQ (PAL)

EV-5145-N1SQ (NTSC)

EV-5145-P1SQ (PAL)

Note: Each set includes only 1 camera.

Includes 1 European plate

ENFORCER Wall-Plate Camera

EV-5105-N1SQ

EV-5105-P1SQ

EV-5145-N1SQ

EV-5145-P1SQ

Type

Wall Plate Camera

Plate type

1 Single-gang, 1 slimline

1 European

CCD

1

/3” Interline Color CCD

Resolution

700 TV Lines

Video output form at

NTSC

PAL

NTSC

PAL

Effective pixel s

976x494 pixels

976x582 pixels

976x494 pixels

976x582 pixels

DNR (2D-NR)

Yes

DWDR

Yes

960H*

Yes

Scanning system

2:1 Interlace

Sync

Internal

Video output

1.0Vp-p Composite video, 75Ω

Lens

2.3mm

Viewing Angle

165° (Diagonal)

Minimum illumination

0.1 Lux

Gamma correcti o n

0.45

S/N Ratio

>52dB

Gain control

Auto

Operating v oltage

12VDC

Current draw

74mA

IP Rating

IP67

Operating temperature

14°~122° F (-10°~50° C)

Camera

11/8”x11/8”x11/4” (28x28x31 mm)

Single-Gang

23/4”x41/2” (70x114 mm)

N/A

Slimline

11/2”x41/2” (38x114 mm)

N/A

European

N/A

37/16”x37/16” (86x86 mm)

Weight (Camera only)

2.8-oz (80g)

Dimensions:

Parts List:

Specifications:

All models i nclude:

EV-5105 models only:
EV-5145 models only:

41/2”

Slimline plate

(EV-5105 models only)
37/16” (86mm)

37/16”

European plate

(EV-5145 models only)

1 x Angled rubber ring

2 x Stainless-steel screws

23/4” (70mm)

41/2”

Single-gang plate

(EV-5105 models only)

11/2” (38mm)

9

/16” (14mm)

11/8”

11/4” (31mm)

13

/16”

(21mm)

11/16”

(27mm)

Camera

*In order to take full advantage of 960H resolution, the camera must be used with a 960H DVR

Dimensions

1 x Manual
1 x Camera
1 x Angled plastic ring

(114mm)

2 SECO-LARM U.S.A., Inc.

1 x Threaded ring

(114mm)

(28mm)

1 x Single-gang plate
1 x Slimline plate

1 x European plate

(86mm)

1. Please read this manual carefully and keep it for

damage the camera, even when not in use.

4. Do not mount the camera in areas exposed to radiation,

Before Starting:

Mounting the Camera to the Plate:

Changing the Mounting Angle:

Install the angled rubber ring on the front of the plate so

With a plate and back box (suggested):

With a plate, but no back box:

With no plate and no back box:

Drill a hole in the

(See Dimensions.)

Drill a hole in the

Back box not included.

Mounting Options:

Max. wall thickness:

BNC connector

Reverse image wire loop*

Plate

Angled rubber ring
12VDC

Note polarity when connecting power

Angled
plastic ring

Camera

IMPORTANT

*To reverse the camera’s image, cut the reverse image

Threaded ring

Overview:

If an object installed next to the camera on the wall is

vision forward.

To mount the camera to the plate, position the angled

Min. wall thickness:

future reference.

2. Use the camera within given temperature and

electrical limits.

3. Do not point the camera at the sun. Heat could

ENFORCER Wall-Plate Camera

strong magnetic fields, or strong electrical signals.

5. Do not open or disassemble the camera. There are no

user-serviceable parts inside.

6. Do not drop the camera or subject it to extreme shock.

rings behind the plate, and twist the threaded ring on
to secure the plate to the camera.

blocking the field of vision, the angled rings may be
installed in front of the wall plate to move the field of

Do not cut the video or power wires as warranty will be voided.

wire loop. To restore the image to default, reattach the
reverse image wire loop. Make sure bare wires are
protected by electrical tape or a similar coating.

wall big enough to
fit the camera.
Mount the plate
directly to the wall.

wall big enough to
fit the camera. If
mounting to a thick

that the camera is tilted. (Approximately 20°)

SECO-LARM U.S.A., Inc. 3

5

/16” (8mm)

3

/4” (20mm)

surface, it may not
be necessary to
use the angled
rings.
(See Dimensions.)

ENFORCER Wall-Plate Camera

MiEV-51x5-x1SQ_141002.docx

PIKSR1

IMPORTANT

Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recor

will not be held responsible for the use of this

product in violation of any current laws

WARNING

Stop using th

smoke or unusual heat, as it could cause fire or electric shock. Do not open

the case of thi

FCC COMPLIAN CE STATEMENT

Information to the user: This equipment has been tested and found to comp

t to

part 15 of the FCC rules.

protection against harmful interference when the equipment

is operate

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause

Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for

LARM’s obligation is limited to the repair or

This Warranty is void if damage is

or alteration, improper or abnormal

LARM determines that such equipment is not operating properly as a

LARM, and the purchaser’s exclusive

LARM be liable for any

NOTICE

The information and specifications

LARM policy is

one of continu

specifications without

notice.

LARM
U.S.A., Inc. or their respective owners.
Copyright © 20

part,

without the written permission of SECO

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606
Tel: 800

Website: www.seco-larm.com
E

The screen is blank.

The screen image is dim

The screen image has poor contrast.

The screen image flickers.

The screen image is distorted.

The camera case is hot.

• Check that the camera is powered up.

•

•

• Check that the video cable connecting the camera to the

• Clean the lens using a soft, clean cloth.

•

• Adjust the monitor’s contrast knob.

•

• Change the position of the camera.

• Change the position of the camera.

• Check that the correct power supply is in use.

Troubleshooting:

ding audio and video signals. SECO-LARM

or statutes.

e camera if you see a malfunction such as

s device, as there are no user-serviceable components inside.

Check that the power supply’s polarity is correct.
Check that the monitor is powered up.

monitor is connected properly.

Check that the light source is adequate.

Change the position of the camera.

d in a commercial environment.

a period of three (3) years from the date of sale to the original consumer customer. SECO­replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair
usage, or faulty installation, or if for any other reason SECO­result of causes other than defects in material and workmanship. The sole obligation of SECO­remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO­special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

SECO-LARM is also not responsible for misprints or typographical errors. Trademarks are the property of SECO-

-662-0800 / 949-261-2999

4 SECO-LARM U.S.A., Inc.

These limits are designed to provide reasonable

or her own expense.

al development and improvement. For this reason, SECO-LARM reserves the right to change

14 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in

printed in this manual are current at the time of publication. However, the SECO-

-LARM.

mail: [e-mail]

ly with the limits for a class B digital device, pursuan

harmful interference to radio communications.