Manual
Corner-Mount Camera
(EV-4606 Model shown)
Model
Format
Covert IR LEDs
TV Lines
EV-4605-N3SQ
NTSC
No
600
EV-4605-P3SQ
PAL
No
600
EV-4606-N3SBQ
NTSC
Yes
700
EV-4606-P3SBQ
PAL
Yes
700
1
/3” Sony Super HAD II CCD
3mm Lens (120° viewing angle)
Weatherproof (IP65)
DWDR (Digital Wide Dynamic
Range) provides clear images in
varying environments
EV-4606 Models Only:
24 Covert IR LEDs for discreet
monitoring in the dark
3D-NR (3D Digital Noise
Reduction) cleans and sharpens
images by reducing camera noise
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
ENFORCER Corner-Mount Camera
Model
EV-4605-N3SQ
EV-4605-P3SQ
EV-4606-N3SBQ
EV-4606-P3SBQ
Type
Corner-Mount Camera
CCD
1
/3” Sony Super HAD II
Resolution
600 TV lines
700 TV lines
960H*
No
Yes
Video output format
NTSC
PAL
NTSC
PAL
Pickup elements
768x494 pixels
752x582 pixels
976x492 pixels
976x582 pixels
DNR
2D-NR
Yes
3D-NR
N/A
Yes
DWDR
Yes
Scanning system
2:1 Interlace
Sync
Internal
Video output
1.0Vp-p composite video, 75Ω
# of IR LEDs
N/A
24 (940nm)
Lens
3mm
Viewing angle
120°
Minimum illumination
0.1 Lux (F/1.4)
0.1 Lux (F/1.4) (LEDs OFF)
0 Lux (F/1.4) (LEDs ON)
Gamma correction
0.45
S/N ratio
>48dB
>52dB
Gain control
Auto
White balance
Auto
Operating voltage
12VDC
Current draw
83mA
83mA (LEDs off)
230mA (LEDs on)
IP Rating
IP65
Operating temperature
14°~122° F (-10°~50° C)
Dimensions
71/2” x51/2”x111/16” (190x140x43 mm)
Weight
15-oz (430g)
Specifications:
Dimensions:
Parts List:
1 x Camera cover
2 x Mounting screws
3 x Security screws
1 x Security wrench
1 x Pigtail connector
1 x Manual
1 x Camera
Note: EV-4606 Model shown. Both models have the same dimensions.
111/16”
(43mm)
51/2”
(140mm)
71/2” (190mm)
*In order to take full advantage of 960H resolution, the camera must be used with a 960H DVR.
2 SECO-LARM U.S.A., Inc.
Installation:
Before Starting:
1. Use the included security wrench to loosen the screws
and remove the camera cover from the camera.
2. Run a 12VDC power supply wire and a video cable with
a male BNC connector through the wall at the corner
where the camera is to be mounted.
3. Temporarily connect the camera to the power supply.
Do not cut DC jack or female BNC connector as
warranty will be voided. If needed, use the included
pigtail connector.
4. While watching the monitor, hold the camera against
the corner where it is to be mounted until it is certain
that this mounting location is correct. Use a pencil to
mark the location of the two screw holes.
5. Disconnect the power supply and video cable.
6. Mount the camera against the corner using the two
included mounting screws. If the wall is made of dry
wall, brick, or similar material, it may be necessary to
use screw anchors (not included).
7. Reconnect the power supply and video cable. Turn the
monitor on and make sure the camera is sending a
proper signal.
8. Attach the base cover using the included
security wrench.
9. Do a final test of the video camera and monitor.
Overview:
Camera cover
Important:
Do not cut DC jack or BNC connector as warranty will be voided.
Pigtail connector
Female BNC connector
DC Jack
Note: EV-4606 Model shown.
Mounting screw
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
4. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.
5. Do not open or disassemble the camera. There are no
field-serviceable parts inside.
6. Do not drop the camera or subject it to
strong vibrations.
Security screw
ENFORCER Corner-Mount Camera
SECO-LARM U.S.A., Inc. 3 SECO-LARM U.S.A., Inc. 33 3
ENFORCER Corner-Mount Camera
MiEV-460x-N3SxQ_1406.docx
PIKSR1
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no user-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for
a period of three (3) years from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair
or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
The screen is blank.
The screen image is dim
The screen image has poor contrast.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
IR LEDs do not turn on.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
Adjust the monitor’s contrast knob.
Change the position of the camera.
Change the position of the camera.
Change the position of the camera.
Check that the correct power supply is in use.
Check that the correct power supply is in use.
Troubleshooting:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Tel: (949) 261-2999 | (800) 662-0800
Email: sales@seco-larm.com
4 SECO-LARM U.S.A., Inc.
Loading...