Seco-Larm EV-2726-NFWQ User Manual

Note: Products with model num bers that end with “Q” or that have a round green “Q” stick er ar e R oH S c om pli ant.

Varifocal Van dal Rollerball Cameras

Manual

NTSC Models

PAL Models

Features

EV-2706-NFGQ

EV-2706-PFGQ

700 TVL, Gray Housing

EV-2706-NFWQ

EV-2706-PFWQ

700 TVL, White Housing

EV-2726-NFGQ*

EV-2726-PFGQ*

700 TVL, 3D-DNR, 2D-DNR, WDR, Gray Housing

EV-2726-NFWQ*

EV-2726-PFWQ*

700 TVL, 3D-DNR, 2D-DNR, WDR, White Housing

*Includes built-in OSD (On-Screen Display) controller

• 1/3” Sony CCD

• 960H High resolution

3X Series – clear images in nearly any lighting situation

• 2.8~12mm Lens

• 3-Axis ball mount for wall or

ceiling mounting

• Weatherproof (IP65)

• Split-glass design to

eliminate IR reflection

• Vandal-resistant design

ENFORCER Varifocal Vandal Ball-Mount Dome Cameras

EV-2706-NFGQ EV-2706-NFWQ

EV-2726-NFGQ EV-2726-NFWQ

EV-2706-PFGQ EV-2706-PFWQ

EV-2726-PFGQ EV-2726-PFWQ

Type

Vandal Rollerball Camer a

CCD

1

/3” Sony Super HAD II

Resolution

700 TV lines

Pickup elements

NTSC

976x494 pixels

PAL

976x582 pixels

3D-NR

No

Yes

WDR

No

Yes

OSD Control

No

Yes

960H*

Yes

Scanning system

2:1 Interlac e

Sync

Internal

Video output

1V p-p composite output, 75 ohms

Lens

2.8~12mm

# of IR LEDs

36 (850nm)

IR Range

Up to 100’ (30m)

LEDs OFF

0.02 Lux

0.03 Lux

LEDs ON

0 Lux

Gamma correcti o n

0.45

S/N Ratio

>52dB

DSS (Digital Slow Shutter)

N/A

256x

Shutter control

Auto Electri c Shutter (AES), 1/60~1/ 100,000 s

Gain control

Auto

White balance

Auto

Operating v oltage

12VDC ±10%

LEDs OFF

100mA

150mA

LEDs ON

400mA

450mA

IP Rating

IP65

Operating temperature

-4°~131° F (-20°~55° C)

Dimensions

411/16”x37/8” (119x98 mm)

Cable length

34” (86cm)

Weight

1-lb, 13-oz (820g)

Dimensions:

Specifications:

Parts List:

1 x Camera

Zoom

411/16” (119mm)

Focus

37/8”

(98mm)

Optional Mounting

Wall Mount

Ceiling Mou n t

Conduit Box

Gray: EV-DWLGQ

White: EV-DWLWQ

Gray: EV-DCLGQ

White: EV-DCLWQ

Gray: EV-DSLGQ

White: EV-DSLWQ

Conduit Drop

Gray: EV-DDLGQ

White: EV-DDLWQ

*In order to t ake full advantage of 960H resolution, the camera must be used wit h a 960H DVR.

Model

NTSC PAL

Minimum illumination

Current draw

Brackets (sold separately):

1 x Manual 4 x Screws 4 x Screw anchors 1 x DC Plug with terminal block 1 x Small screwdriver 1 x Hex wrench 2 x Rubber plugs

2 SECO-LARM U.S.A., Inc.

ENFORCER Varifocal Vandal Ball-Mount Dome Cameras

1. Please read this manual carefully and keep it for

3.

Do not point the camera at the sun. Heat could damage

Before Starting:

1.

Run a 12VDC power s upply wire an d a video cable

Installation:

5. Put the case over the camera ball onto the base. Be

Insert the ru bber plugs ov er the zoom and focus to prevent

Overview:

Camera ball

Case

Base

Screws

Female BNC

DC Plug with DC Jack

Rubber Plug

Installation

OSD Controller

(Only 2 shown. Use all 4 when installing.)

connector

future reference.

2. Use the camera withi n the given tem perature and

electricity limits.

with a male BN C connector through the wall to where the camera is to be mounted.

2. Loosen the set screws w ith the included hex wre nch

and remove th e case from th e base. NOTE: The camera ball is NOT attached t o the case or the base. It sits loose inside the case. Therefore, be very careful when removing the case from the base. Do not drop the camera ball.

3. Mount the base to the wall using th e four included

mounting screws. If the wall is made of dry wall, brick, or similar material, it may be necessary to use the included plastic screw anchors.

4. Run the camera’s BNC and power connectors

through the camera base, and connect to the video and power wires that were r un through th e wall.

SECO-LARM U.S.A., Inc. 3

terminal block

the camera, even when not in use.

4. Do not drop the camera or subject i t to strong vibrations.

5. Do not m ount the camera in areas exposed to radiation,

strong magn etic fields, or strong electrical signals.

careful to not drop the camera ball.

6. Holding the case loosely on the bas e, turn the camera

ball to the des ired directi on. Use the inc luded small screwdriver to adjust the z oom and focus of the camera ball if neede d, via the holes marked “ZOOM” and “FOCUS” on the top of the camera ball. NOTE: Before securing i nstallation, make sure to check both the day and night images. Adjust the camera ball so that there ar e no objects blocking the camera’s view.

7. WDR Model s Onl y: Use the OSD controller joystick to

adjust camera settings (see the separ ate OSD manual).

8. Once the ball is pointing in the desi red direction, tighten

the outer case ring to secure the camera in its position.

9. Do a final test of the video camera and monitor.

10.

tampering.

(WDR Models only)

ENFORCER Varifocal Vandal Ball-Mount Dome Cameras

MiEV-27x6-NFxQ _1402.docx

PICSN4

IMPORTANT

Users and install ers of this product ar e r esponsible for ensuring this product complies wit h all national, state, and local l statutes related to monitoring and r ecording audio and video signals. product in violati on of any current law s or statutes.

WARNING

Stop using the came

smoke or unusu al heat, as it could ca use fire or electric shock. Do not open

the case of thi

FCC COMPLIAN CE STATEMENT

Information to the user: This equipment has been tested and found to comp part 15 of the equipment is oper ated in a commerci al environment. This equipment generates, uses, a nd can radiate radi o f r equency energy and, if not installed an Operation of this equipment in a resi dential area is likely to cause harmful interference i n which case the us er w ill be requ correct the inte

WARRANTY: This SECO-LARM product is warranted against defects in mater i al and workmanship while used in nor m al service

for a period of thre e (3) years from the date of sale to the ori ginal customer. S ECO replacement of a ny defective part if the unit is returned, transportati on prepaid, to SEC O This Warranty is voi d if damage is caused by or attribut ed t o acts of God, physi c al or electrical m isuse or abuse, neglect, r alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determin es t hat such equipment is not operating pr operly as a result of causes other than defects in material and workmans hi p. The sole obligation SECO property damage s of any

NOTICE

The information and specificati ons printed in this m anual are current at the time of publication. However, the SECO one of continual d evelopment and i m pr ovement. For this reason, SECO notice. SECO

without the

SECO-LARM

16842 Millikan Avenue, Irvine, CA 92606 Tel: 800

Website: www.seco-larm.com E

Troubleshooting:

• Check that the camera is powered up

The screen is black

The image is foggy or washed out at night

• Check that the power supply’s polarity is correct

• Check that the monitor is powered up

• Check that the video cabl e connecting the camera to the

monitor is connected properly

• Check that there are no objects very c lose to the camer a

• Check that there are no highly reflecti ve objects in the scene

The screen im age is dim

The screen im age has poor contrast The screen im age flickers

The screen im age is distorted The camera case is hot IR LEDs do not t urn on

ra if you see a malfunction such as

s device, as ther e are no field-serviceable components inside.

FCC rules. Thes e limits are designe d t o provide reasonable protection against harmful interference when the

d used in accordance with the instru c t ion manual, may cause harmful int er ference to radio c ommunications.

rference at his or her own ex pense.

• Clean the lens using a soft, clean cloth

• Check that the light source is adequate

• Adjust the monitor’s contrast knob

• Change the position of the camera

• Change the position of th e camera

• Check that the correct pow er supply is in use

aws and

SECO-LARM will not be held responsible for the us e of this

ly with the limits for a class B digital device, pur suant to

ired to

-LARM’s obligation is limited to the repai r or

-LARM. epair or

-LARM’s option. In no event shall SE CO-LARM be liable for any special, coll ateral, incidental , or consequential personal or

4 SECO-LARM U.S.A., Inc.

of SECO-LARM and the purchaser’s exclusive r emedy, shall be limited to replacement or repair only , at

kind to the purc haser or anyone else.

-LARM is also not responsible for misprints or typogr aphical errors. 14 SECO-

written permission of SECO-LARM.

-LARM reserves the right to change s pecifications wit hout

U.S.A., Inc.

-662-0800 / 949-261-2999

-mail: sales@seco-larm.com

-LARM policy is