Page 1
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Manual
Vandal Rollerball Cameras
NTSC Models
PAL Models
Features
EV-2706-N3GQ
EV-2706-P3GQ
700 TVL, Gray housing
EV-2706-N3WQ
EV-2706-P3WQ
700 TVL, White housing
•
1
/3” Sony CCD
• 960H High resolution
EV-2726-N3GQ*
EV-2726-P3GQ*
700 TVL, 3D-NR, 2D-NR, WDR, Gray housing
EV-2726-N3WQ*
EV-2726-P3WQ*
700 TVL, 3D-NR, 2D-NR, WDR, White housing
3X Series – clear images in nearly any lighting situation
*Includes built-in OSD (On-Screen Display) controller
• 3.6mm Lens
• 3-Axis ball mount for wall or
ceiling mounting
• Weatherproof (IP65)
• Split-glass design to
eliminate IR reflection
• Vandal-resistant design
Page 2
ENFORCER Vandal Ball-Mount Dome Cameras
EV-2706-N3GQ
EV-2706-N3WQ
EV-2726-N3GQ
EV-2726-N3WQ
EV-2706-P3GQ
EV-2706-P3WQ
EV-2726-P3GQ
EV-2726-P3WQ
Type
Vandal Rollerball Camera
CCD
1
/3” Sony Super HAD II
Resolution
700 TV lines
700 TV lines
Pickup
elements
NTSC
976x494
976x494
PAL
976x582
976x582
DNR (2D-NR and 3D-NR)
No
Yes
WDR
No
Yes
OSD Control
No
Yes
960H*
Yes
Scanning system
2:1 Interlace
Sync
Internal
Video output
1.0V p-p Composite output, 75Ω
Lens
3.6mm
# of IR LEDs
24 (850nm)
IR Range
Up to 50’ (15m)
Minimum
illumination
LEDs OFF
0.06 Lux
0.03 Lux
LEDs ON
0 Lux
Gamma correcti o n
0.45
S/N Ratio
>48dB
>52dB
DSS (Digital Slow Shutter)
N/A
256x
Shutter control
Auto Electric Shutter (AES), 1/60~1/100,000 s
Gain control
Auto
White balance
Auto
Operating v oltage
12VDC
LEDs OFF
95mA
150mA
LEDs ON
270mA
450mA
IP Rating
IP65
Operating temperature
-4°~122° F (-20°~50° C)
Dimensions
311/16”x35/32” (94x80 mm)
Cable length
38” (98cm)
Weight
14-oz (400g)
Dimensions:
Specifications:
Parts List:
1x Camera
1x Hex wrench
35/32”
Optional Mounting
Wall Mount
Ceiling Mou n t
Conduit Box
Gray: EV-DWSGQ
White: EV-DWSWQ
Gray: EV-DCSGQ
White: EV-DCSWQ
Gray: EV-DSSGQ
White: EV-DSSWQ
311/16” (94mm)
*In order to take full advantage of 960H resolution, the camera must be used with a 960H DVR.
Model
NTSC
PAL
Current draw
Brackets (sold separately):
1x Manual
4x Screws
4x Screw anchors
1x DC Plug with
terminal block
(80mm)
2 SECO-LARM U.S.A., Inc.
Page 3
ENFORCER Vandal Ball-Mount Dome Cameras
1. Please read this manual carefully and keep it for
4. Do not drop the camera or subject it to
Before Starting:
1. Run a 12VDC power supply wire and a video cable
Installation:
5. Put the case over the camera ball onto the base. Be
Overview:
Camera ball
Case
Base
Screws
Female BNC
DC Plug with
DC Jack
OSD Controller
(Only 2 shown. Use all 4 when installing.)
terminal block
connector
(3X Models only)
future reference.
2. Use the camera within the given temperature and
electricity limits.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
with a male BNC connector through the wall to where
the camera is to be mounted.
2. Loosen the set screws with the included hex wrench
and remove the case from the base.
NOTE: The camera ball is NOT attached to the case
or the base. It sits loose inside the case. Therefore,
be very careful when removing the case from the
base. Do not drop the camera ball.
3. Mount the base to the wall using the four included
mounting screws. If the wall is made of dry wall, brick,
or similar material, it may be necessary to use the
included plastic screw anchors.
4. Run the camera’s BNC and power connectors through
the camera base, and connect to the video and power
wires that were run through the wall.
SECO-LARM U.S.A., Inc. 3
strong vibrations.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
careful to not drop the camera ball.
6. Holding the case loosely on the base, turn the camera
ball to the desired direction.
NOTE: Before securing installation, make sure to check
both the day and night images. Adjust the camera ball
so that there are no objects blocking or obscuring the
camera’s view.
7. 3X Models Only: Use the OSD controller joystick to
adjust camera settings (see the separate OSD manual).
8. Once the ball is pointing in the desired direction,
tighten the outer case ring to secure the camera in
its position.
9. Do a final test of the video camera and monitor.
Page 4
ENFORCER Vandal Ball-Mount Dome Cameras
MiEV-27x6-N3xQ.docx
PICSN4
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local l
statutes related to monitoring and recording audio and video signals.
product in violation of any current laws or statutes.
WARNING
Stop using the came
smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of thi
FCC COMPLIAN CE STATEMENT
Information to the user: This equipment has been tested and found to comp
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
correct the interference at his
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a perio
replacement of any defective part if the unit is returned, transportation prepaid, to SECO
This Warranty is void if damage is caused
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a
The sole obligation of SECO
SECO
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO
one of
notice. SECO
Copyright © 20
served. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO
SECO-LARM
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800
Website: www.seco-larm.com
E
Troubleshooting:
• Check that the camera is powered up
The screen is black
The image is foggy or washed out at night
• Check that the power supply’s polarity is correct
• Check that the monitor is powered up
• Check that the video cable connecting the camera to the
monitor is connected properly
• Check that there are no objects very close to the camera
• Check that there are no highly reflective objects in the scene
The screen image is dim
The screen image has poor contrast
The screen image flickers
The screen image is distorted
The camera case is hot
IR LEDs do not turn on
• Clean the lens using a soft, clean cloth
• Check that the light source is adequate
• Adjust the monitor’s contrast knob
• Change the position of the camera
• Change the position of the camera
• Change the position of the camera
• Check that the correct power supply is in use
• Check that the correct power supply is in use
SECO-LARM will not be held responsible for the use of this
ra if you see a malfunction such as
s device, as there are no field-serviceable components inside.
ly with the limits for a class B digital device, pursuant to
or her own expense.
d of one (3) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
-LARM.
by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
the user will be required to
aws and
result of causes other than defects in material and workmanship.
-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
4 SECO-LARM U.S.A., Inc.
-LARM is also not responsible for misprints or typographical errors.
14 SECO-LARM U.S.A., Inc. All rights re
-662-0800 / 949-261-2999
-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
-LARM.
U.S.A., Inc.
-mail: sales@seco-larm.com
-LARM policy is
Loading...