Page 1
IR LED Bullet Cameras
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS -compliant products.
Manual
1
/3” Sony Super HAD II CCD
Weatherproof
Optimized to produce clear
images at night
Cables concealed in bracket
12VDC Operation
only:
OSD (On-Screen Display) for
programming special features
960H High resolution
(42-LED version shown)
Use to access the OSD
(On-Screen Display)
functions for
compatible cameras
without having to be
near the camera.
For more information, please see the EV-18C manual.
OSD Controller
Model No.
EV-18C
Not included.
NTSC Model #
PAL Model #
Lens
Resolution
IR
LEDs
OSD
EV-1186-N3GQ
EV-1186-P3GQ
3.6mm
480 TV lines
30
No
EV-1806-N3GQ
EV-1806-P3GQ
3.6mm
700 TV lines
30
No
EV-1196-N6GQ
EV-1196-P6GQ
6.0mm
480 TV lines
42
No
EV-1816-N6GQ
EV-1816-P6GQ
6.0mm
700 TV lines
42
Yes
EV-1196-NKGQ
EV-1196-PKGQ
2.8~12mm
480 TV lines
42
No
EV-1816-NKGQ
EV-1816-PKGQ
2.8~12mm
700 TV lines
42
Yes
Page 2
ENFORCER IR LED Bullet Cameras
Model #
Lens
IP Rating
EV-1186-N3GQ
EV-1186-P3GQ
3.6mm
IP67
EV-1806-N3GQ
EV-1806-P3GQ
3.6mm
IP67
EV-1196-N6GQ
EV-1196-P6GQ
6.0mm
IP67
EV-1816-N6GQ
EV-1816-P6GQ
6.0mm
IP67
EV-1196-NKGQ
EV-1196-PKGQ
2.8~12mm
IP66
EV-1816-NKGQ
EV-1816-PKGQ
2.8~12mm
IP66
Dimensions:
1 x IR Camera
1 x Hex wrench
1 x Sunshield
1 x Manual
1 x DC Plug with terminal block
4 x Mounting screws
4 x Screw anchors
Specifications:
Lens and IP Rating:
Parts List:
69/16” (167mm)
7” (177mm)
31/8”
(80mm)
31/8”
(80mm)
77/8” (200mm)
711/16” (195mm)
30-LED Models
42-LED Models
Model
NTSC
EV-1186-N3GQ
EV-1806-N3GQ
EV-1196-N6GQ
EV-1196-NKGQ
EV-1816-N6GQ
EV-1816-NKGQ
PAL
EV-1186-P3GQ
EV-1806-P3GQ
EV-1196-P6GQ
EV-1196-PKGQ
EV-1816-P6GQ
EV-1816-PKGQ
Type
IR LED Bullet Camera
CCD
1
/3” Sony Super HAD II
Resolution
480 TV lines
700 TV lines
480 TV lines
700 TV lines
Pickup
elements
NTSC
510x492 pixels
976x492 pixels
510x492 pixels
976x492 pixels
PAL
500x528 pixels
976x582 pixels
500x528 pixels
976x582 pixels
DNR (2D-NR)
Yes
Yes
Yes
Yes
OSD Control
No
No
No
Yes
960H*
No
Yes
No
Yes
Scanning system
2:1 Interlace, V: 59.94Hz, H: 15.734KHz
Sync
Internal
Video output
1.0Vp-p Composite video, 75Ω
# of IR LEDs
30
42
IR Range
Up to 75ft (23m)
Up to 105ft (32m)
Minimum
illumination
LEDs OFF
0.1 Lux
LEDs ON
0 Lux
Gamma correction
0.45
S/N Ratio
>48dB
Shutter control
Auto Electric Shutter (AES)
Gain control
Auto
White balance
Auto
Operating voltage
12VDC
Current draw
LEDs OFF
87mA
95mA
87mA
95mA
LEDs ON
260mA
270mA
330mA
350mA
Operating temperature
14~122 F (-10~50 C)
Dimensions
7”x31/8”x31/8” (177x80x80 mm)
77/8”x31/8”x 31/8” (200x80x80 mm)
Weight
12-oz (340g)
1-lb 2-oz (510g)
*In order to take full advantage of 960H resolution, the camera must be used with a 960H DVR.
31/8” (80mm)
21/2”
(65mm)
215/16”
(75mm)
215/16” (75mm)
31/2” (90mm)
215/16”
(75mm)
31/8”
(80mm)
33/8” (85mm)
2 SECO-LARM U.S.A., Inc.
Page 3
Overview:
*EV-1196-NKGQ and EV-1816-NKGQ only.
1. Run a 12VDC power supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted.
2. Temporarily connect the camera to the 12VDC power
supply. Do not cut the DC jack or female BNC plug
as warranty will be voided. If needed, use the
included SECO-LARM DC plug with terminal block.
3. Temporarily connect the camera’s female BNC jack to
the video cable’s male BNC plug. While watching the
monitor, hold the camera bracket by hand against the
wall where it is to be mounted, then twist the camera
until it is certain that this mounting location is correct.
Use a pencil to mark the location of the four screw
holes in the bracket.
4. Disconnect the 12VDC power supply and video cable.
5. Mount the bracket to the wall using the four included
mounting screws.
6. Reconnect the 12VDC power supply and video cable.
Turn the monitor on and make sure the camera is
sending the proper video signal.
7. To adjust the camera angle, loosen and tighten the
adjustment nut, or loosen and tighten either of the two
screws on the mounting arm. Adjust until the desired
scene is displayed.
8. only: Use the OSD controller (sold separately)
or in-line OSD joystick to adjust camera settings (see the
separate OSD manual).
9. Adjust the zoom and focus using the included hex
wrench. (Varifocal models only.)
10. Do a final test of the video camera and monitor.
Mounting to Lamp Holder Cover Plate
1. Remove mounting base by loosening adjustment screw
and adjustment nut before removing the mounting base
by twisting.
2. Screw the camera onto a lamp holder cover plate and
tighten the adjustment nut and adjustment screw.
Sunshield screw
Installation:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not aim the LED light directly at the eyes when the
LEDs are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong electrical
signals.
6. Do not open or disassemble the camera. There are
no field serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
Before Starting:
Mounting base
Camera angle
adjustment screw
Adjustment nut
Mounting arm
adjustment screw
Mounting
arm
Sunshield
Zoom*
Focus*
Surface mount
knock-out
Remove with a pair of
pliers
Adjustment
screw
Female BNC
connector
DC Plug with
terminal block
DC Jack
ENFORCER IR LED Bullet Cameras can be mounted to a standard lamp holder cover plate (not included).
Unscrew the mounting base from the mounting arm and screw onto the fitting.
In-line OSD joystick
( only)**
**Optional Zeta Series OSD Controller available for added convenience. (Model #: EV-18C)
ENFORCER IR LED Bullet Cameras
SECO-LARM U.S.A., Inc. 3 SECO-LARM U.S.A., Inc. 33 3
Page 4
ENFORCER IR LED Bullet Cameras
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor contrast.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
IR LEDs do not turn on.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of three (3) years from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: sales@seco-larm.com
MiEV-1xx6-NxGQ_1309_New.docx
PICSN5
Troubleshooting:
4 SECO-LARM U.S.A., Inc.
Loading...