Page 1
Manual
EV-1665-N2BQ
170° Wide Angle Bullet Camera
Wide 170° viewing angle
2.2mm lens
600 TV lines
1
/3” Sony Super HAD II CCD
Weatherproof (IP66)
Digital Noise Reduction (DNR)
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Page 2
ENFORCER 170° Wide Angle Bullet Camera
Type
Wide-Angle Bullet Camera
CCD
1
/3” Sony Super HAD II Color CCD
Resolution
600 TV lines
Pickup elements
768x494 pixels
Video output format
NTSC
Video output
1.0Vp-p composite video, 75Ω
Lens
2.2mm
Viewing angle
170°
Minimum illumination
0.1-lux at F/1.4
S/N ratio
>48dB
Scanning frequency
15.734KHz x 59.94Hz
Sync
Internal
Gamma correction
0.45
Gain control
Auto
IP rating
IP66
Power source
12VDC
Current draw
83mA
Operating temperature
14°~122° F (-10°~50° C)
Dimensions
31/8”x11/2”x11/2” (80x37x37 mm) (without sunshield)
Weight
9.2-oz (261g)
Specifications
Parts List:
Dimensions:
1 x Sunshield
1 x Manual
6 x Mounting screws
1 x Pigtail connector
1 x Camera
1 x Mounting bracket
311/16” (93mm)
31/8” (80mm)
11/2”
(37mm)
19/16”
(40mm)
11/2”
(37mm)
SECO-LARM U.S.A., Inc.
Page 3
Installation:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not mount the camera where it is exposed to
rain or other moisture, or in humid or dusty places.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.*
6. Do not open or disassemble the camera. There
are no field-serviceable parts inside.
7. Do not drop the camera or subject it to
strong vibrations.
Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during
de-Gaussing, which occurs automatically with
many monitors when the monitor is turned on.
Before Starting:
1. Run a 12VDC power supply wire and a video
cable with a male BNC connector through the
wall to where the camera is to be mounted.
2. Temporarily connect the camera to the power
supply. Do not cut DC jack or female BNC
connector as warranty will be voided. If
needed, use the included pigtail connector.
3. Temporarily connect the camera’s female BNC
connector to the video cable’s male
BNC connector.
4. While watching the monitor, hold the camera
against the wall or ceiling by hand where it is to
be mounted, then turn the camera until it is
certain that this mounting location is correct. Use
a pencil to mark the location of the six screw
holes in the mounting plate.
5. Disconnect the power supply and video cable.
6. Mount the mounting plate to the wall or ceiling
using the six included mounting screws. If the
wall is made of dry wall, brick, or similar material,
it may be necessary to use screw anchors
(not included).
7. For ceiling mounting, remove the sunshield and
attach the mounting bracket to the top of the
camera. (Sunshield must be removed for
ceiling mounting.)
8. Reconnect the power supply and video cable.
Turn the monitor on and make sure the camera
is sending the proper video signal.
9. Adjust the camera angle using the adjustment nut.
10. Do a final test of the video camera and monitor.
Overview:
Mounting holes
Important:
Do not cut DC jack or female BNC connector as warranty will be voided.
Camera
Sunshield
Adjustment nut
BNC connector
DC jack
Pigtail connector
Connect to video cable’s
male BNC connector
Mounting bracket
Ceiling mounting
Remove sunshield and
attach mounting bracket to
the top of the camera.
ENFORCER 170 ° Wide Angle Bullet Camera
SECO-LARM U.S.A., Inc.
Page 4
ENFORCER 170° Wide Angle Bullet Camera
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: sales@seco-larm.com
MiEV-1665-x2BQ_1106.docx
PIKSR1
Troubleshooting
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the
camera to the monitor is connected properly.
The screen image is dim.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor
contrast.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
SECO-LARM U.S.A., Inc.
Loading...