Page 1
1
/
3
”
Sony Super HAD II CCD IR Day/Night Weatherproof
IR LEDs for Nighttime Use Up to 50ft (15m) Range
NTSC
Model
PAL
Model
Lens
Size
Viewing
Angle
# of
IR LEDs
EV-1026-N2SQ
EV-1026-P2SQ
2.9mm
120°
12
EV-1026-N3SQ
EV-1026-P3SQ
3.6mm
92°
24
EV-1026-N6SQ
EV-1026-P6SQ
6.0mm
53°
24
EV-1606-N2SQ
EV-1606-P2SQ
2.9mm
120°
12
EV-1606-N3SQ
EV-1606-P3SQ
3.6mm
92°
24
EV-1606-N6SQ
EV-1606-P6SQ
6.0mm
53°
24
Day/Night Camera
SECO-LARM
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
600 TV Lines
480 TV Lines
Manual
(EV-1026-N3SQ shown)
Page 2
ENFORCER Day/Night Camera
Model #
NTSC
1026-N2SQ
1026-N3SQ
1026-N6SQ
1606-N2SQ
1606-N3SQ
1606-N6SQ
PAL
1026-P2SQ
1026-P3SQ
1026-P6SQ
1606-P2SQ
1606-P3SQ
1606-P6SQ
Type
IR bullet camera
CCD
1
/3” Sony Super HAD II
Resolution
480 TV lines
600 TV lines
Pickup elements
510x492 pixels (NTSC), 500x582 pixels (PAL)
768x494 pixels (NTSC), 752x582 pixels (PAL)
Sync
Internal
Video output
1.0Vp-p composite video, 75Ω
Lens
2.9mm
3.6mm
6.0mm
2.9mm
3.6mm
6.0mm
Viewing angle
120°
92°
53°
120°
92°
53°
Minimum illumination
0.05 Lux (LEDs off)
0.02 Lux (LEDs off)
0 Lux (LEDs on)
0 Lux (LEDs on)
Gamma correction
0.45
S/N ratio
>48dB
Shutter control
Auto Electric Shutter (AES)
Gain control
Auto
IP rating
IP66
# of infrared LEDs
12 (850nm)
24 (850nm)
24 (850nm)
12 (850nm)
24 (850nm)
24 (850nm)
LED range
Up to 40ft
(12m)
Up to 50ft
(15m)
Up to 50ft
(15m)
Up to 40ft
(12m)
Up to 50ft
(15m)
Up to 50ft
(15m)
Operating voltage
12VDC ±10%
Current
draw
LEDs OFF
75mA
95mA
LEDs ON
150mA
250mA
250mA
170mA
270mA
270mA
Operating
temperature
-4°~122° F (-20°~50° C)
Dimensions
311/
16
”x2
5
/16”x2” (94x59x50 mm) with sunshield
Weight
10-oz (280g)
Dimensions:
25/16” (59mm)
13/4” (44mm)
Parts List:
1 x Manual
1 x IR Camera
1 x Sunshield
3 x Mounting bracket
1 x DC Plug with
terminal block
3 x Mounting screws
3 x Screw anchors
(EV-1026-N3SQ shown)
Specifications
213/16” (72mm)
13/8”
(35mm)
5
/8”
(15mm)
2”
(50mm)
311/16” (94mm)
2 SECO-LARM U.S.A., Inc.
Page 3
1. Run a 12VDC power-supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted (if necessary).
2. Assemble the mounting bracket; then screw it into the
back of the camera. Tighten the adjustment nut.
3. Temporarily connect the camera to the 12VDC power
supply. Do not cut DC jack or female BNC
connector as warranty will be voided. If needed,
use the included SECO-LARM DC plug with
terminal block.
4. Temporarily connect the camera’s female BNC
connector to the video cable’s male BNC connector.
5. While watching the monitor, hold the camera bracket
by hand against the wall where it is to be mounted,
then twist the camera until it is certain that this
Installation:
mounting location is correct. Use a pencil to mark the
location of the three screw holes in the bracket.
6. Disconnect the 12VDC power supply and video cable.
7. Mount the bracket to the wall using the three included
mounting screws. If the wall is made of drywall, brick, or
similar material, it may be necessary to use the three
included screw anchors.
8. Reconnect the 12VDC power supply and video cable.
Turn the monitor on and make sure the camera is sending
the proper video signal.
9. To adjust the camera angle, loosen and tighten the
bracket’s thumb screw. Turn the camera and change its
angle relative to the bracket until the desired scene is
displayed.
10. Do a final test of the video camera and monitor.
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electricity limits.
3. Do not aim the LED light directly at the eyes when the
LEDs are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
5. Do not mount the camera in areas exposed to radiation,
strong magnetic fields, or strong electrical signals.
6. Do not open or disassemble the camera. There are no
field serviceable parts inside.
7. Do not drop the camera or subject it to strong vibrations.
Before Starting:
Important:
Do not cut DC jack or female
BNC connector as warranty
will be voided.
Overview:
Important: Do not remove label or open case as warranty will be voided.
Sunshield
(EV-1026-N3SQ shown)
Mounting
bracket
Thumb screw
Female BNC
connector
DC Jack
DC Plug with
terminal block
ENFORCER Day/Night Camera
SECO-LARM U.S.A., Inc. 3 SECO-LARM U.S.A., Inc. 33 3
Page 4
ENFORCER Day/Night Camera
Troubleshooting
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor contrast.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
IR LEDs do not turn on.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of three (3) years from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: sales@seco-larm.com
MiEV-1026_EV-1606_1208.docx
PICSN4
4 SECO-LARM U.S.A., Inc.
Loading...