Page 1
Mini Bullet Camera
EV-1125-N3BQ (NTSC)
EV-1125-P3BQ (PAL)
Manual
1
/3” Sony Super HAD II CCD
3.6mm lens
480 TV lines
Weatherproof (IP66)
12VDC Operation
Low current draw: 150mA
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Page 2
ENFORCER Mini Bullet Camera
Model #
EV-1125-N3BQ
EV-1125-P3BQ
Type
Bullet Camera
CCD
1
/3” Sony Super HAD II Color CCD
Resolution
480 TV lines
Pickup elements
768 x 494 pixels
752 x 582 pixels
Video output format
NTSC
PAL
Video output
1.0Vp-p composite video, 75Ω
Lens
3.6mm
Minimum illumination
0.1 Lux
S/N ratio
>48dB
Sync
Internal
White balance
Auto
Gain control
Auto
Back light compensation
Auto
IP rating
IP66
Power source
12VDC
Current draw
150mA
Operating temperature
14°~122° F (-10°~50° C)
Dimensions
315/16” x 19/16” x 19/16” (100 x 40 x 40mm)
(without sunshield or mounting base)
Weight
7.05-oz (200g)
Specifications:
Parts List:
Dimensions:
1 x Sunshield
1 x Manual
3 x Mounting screws
1 x DC Plug with terminal block
1 x Camera
1 x Mounting bracket
2
41/8” (105mm)
315/16” (100mm)
113/16”
(46mm)
17/8”
(48mm)
19/16”
(40mm)
SECO-LARM U.S.A., Inc.
Page 3
Installation:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not open or disassemble the camera. There
are no field-serviceable parts inside.
6. Do not drop the camera or subject it to
strong vibrations.
Before Starting:
1. Run a 12VDC power supply wire and a video
cable with a male BNC connector through the
wall to where the camera is to be mounted.
2. Temporarily connect the camera to the power
supply. Do not cut DC jack or female BNC
connector as warranty will be voided.
If needed, use the included SECO-LARM
DC plug with terminal block.
3. Connect the BNC connector to a test monitor.
4. While watching the monitor, hold the camera
against the wall by hand where it is to be
mounted, then turn the camera until it is certain
that this mounting location is correct.
5. Use a pencil to mark the location of the three
screw holes in the mounting plate.
6. Disconnect the power supply and video cable.
7. If alternate mounting is desired, remove the
bracket by loosening the bracket screw. Attach
the bracket to the back of the camera.
8. Mount the mounting plate to the wall using the
three included mounting screws. If the wall is
made of dry wall, brick, or similar material,
it may be necessary to use screw anchors
(not included).
9. Reconnect the power supply and video cable.
Turn the monitor on and make sure the camera
is sending the proper video signal.
10. Adjust the camera angle using the adjustment nut.
11. Do a final test of the video camera and monitor.
Overview:
Mounting holes
Important:
Do not cut DC jack or female BNC connector as warranty will be voided.
Camera
Sunshield
Adjustment nut
Female
BNC connector
DC jack
Mounting bracket
DC plug with
terminal block
3
Remove the base from the bottom by twisting the bracket
screw. Attach the base to the back of the camera.
Alternate Mounting Method
Bracket screw
ENFORCER Mini Bullet Camera
SECO-LARM U.S.A., Inc.
Page 4
ENFORCER Mini Bullet Camera
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: sales@seco-larm.com
MiEV-1125-N3B_1205.docx
PICSN5
Troubleshooting
The screen is blank.
connected properly.
The screen image is dim.
The screen image has poor contrast.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
4
SECO-LARM U.S.A., Inc.
Loading...