Page 1
®
Wall-Plate Cameras
Manual
Features:
Wide angle lens
960H high resolution
Weatherproof IP67 construction
Vandal-resistant design
Adjustable mounting angle
Includes: 1 camera, 1 single-gang plate,
1 slimline plate, and angled mounting rings
WDR and 2DNR
Model # Video Output Effective Pixels
EV-5105-N1SQ NTSC 976x494 pixels
EV-5105-P1SQ PAL 976x582 pixels
Page 2
ENFORCER Wall-Plate Cameras
2 SECO-LARM U.S.A., Inc.
1x Camera 1x Single-gang plate 1x Slimline plate
2x Mounting screws 1x
A
ngled aluminum ring 1x Angled rubber ring
1x
A
luminum hex nut 1x Manual
Model EV-5105-N1SQ EV-5105-P1SQ
Type Wall-plate camera
Plate type 1 Single-gang, 1 slimline
Image sensor
1
/3" Interline Color CCD
Resolution 700 TV Lines
Video output format NTSC PAL
Effective pixels 976x494 976x582
2DNR Yes
WDR Yes
960H* Yes
Scanning system 2:1 Interface
Sync Internal
Video output 1.0Vp-p Composite video, 75Ω
Lens 2.3mm
Viewing angle 165°
Minimum illumination 0.1Lux
Gamma correction 0.45
S/N Ratio >52dB
Gain control Auto
Operating voltage 12VDC
Current draw 74mA
IP Rating IP67
Operating temperature 14°~122° F (-10°~50° C)
Dimensions
Camera
1
1
/8"x11/8"x11/2" (28x28x38 mm) 11/8"x11/8"x11/4" (28x28x31 mm)
Single-gang plate
2
3
/4"x41/2" (70x114 mm)
Slimline plate
1
1
/2"x41/2" (38x114 mm)
Weight 3.5-oz (100g)
Parts List:
Specifications:
Dimensions:
Camera body
11/8"
(
28mm)
7
/8"
(
22mm)
11/2" (38mm)
Slimline plate
41/2"
(114mm)
41/2"
(114mm)
23/4" (70mm)
Single-gang plate
*In order to take full advantage of 960H resolution, the camera must be used with a 960H DVR
11/2" (38mm)
Dimensions for the EV-5105-N1SQ shown
7
/8"
(22mm)
Parts list for the EV-5105-N1SQ shown
Page 3
ENFORCER Wall-Plate Cameras
SECO-LARM U.S.A., Inc. 3
Before Starting:
Overview:
Mounting the Camera to the Plate: Mounting Options:
Changing the Mounting Angle:
To mount the camera to the plate, position the angled
rings behind the plate and twist the aluminum hex nut
on to secure the plate to the camera.
Plate
Camera
Female BNC connector
DC Jack
Note polarity when connecting power
IMPORTANT: Do not cut the video or power wires as warranty will be voided.
Install the angled rubber ring on the front of the plate
so that the camera is tilted (approximately 20°).
If an object installed next to the camera on the wall
is blocking the field of vision, the angled rings may
be installed in front of the wall plate to move the
field of vision forward.
Mount directly to the back box (not included).
Drill a 7/8" (22mm) hole in the wall to fit the camera
body. Mount the plate directly to the wall.
Drill a
7
/8" (22mm) hole into the wall to fit the camera
body. If mounting to a thick surface, it may not be
necessary to use the angled rings.
With a plate and back box (suggested):
Aluminum hex nut
Plate, no back box:
No Plate and no Back Box:
Back
box
Min. wall thickness:
5
/16" (8mm)
EV-5105-N1SQ shown
Max. wall thickness:
3
/4" (20mm)
1. Read this manually carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.
5. Do not open or disassemble the camera. There
are no user-serviceable parts inside.
6. Do not subject the camera to extreme shock.
Angled
aluminum ring
Angled rubber ring
Page 4
ENFORCER Wall-Plate Cameras
4 SECO-LARM U.S.A., Inc.
The screen is blank
Check that the camera is powered up
Check that the power supply's polarity is correct
Check that the monitor is powered up
Check that the video cable connecting the camera to
the monitor is connected properly
The screen image is dim
Clean the lens using a soft, clean cloth
The screen image has poor contrast
Adjust the monitor's contrast knob
Change the position of the camera
The screen image flickers
Change the position of the camera
The screen image is distorted
Change the position of the camera
The camera case is hot
Check that the correct power supply is in use
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state,
and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held
responsible for the use of this product in violation of any current laws or statutes.
Troubleshooting:
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Phone:
(
949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com
®
PITSW1
Order Part# 764-100-6%
MI_EV-5105-x1SQ_172803.docx
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric
shock. Do not open the case of this device, as there are no user-serviceable components inside.
Do not cut any wires as the warranty will be voided.
FCC COMPLIANCE STATEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the
device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure
re
q
uirements and void user’s authority to operate the device.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM
reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints.
A
ll trademarks
are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2017 SECO-LARM U.S.A., Inc. All
ri
g
hts reserved.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
Also Available:
4-in-1 HD Vandal Dome Camera 4-in-1 HD UFO Camera 4-in-1 HD Corner-mount Camera
Loading...