SECO-LARM ENFORCER E-964-Q660Q, ENFORCER E-964-Q495Q, ENFORCER E-964-Q330Q, ENFORCER E-964-Q165Q User Manual

Download

Page 1

ENF ORCER

SENSOR

MANUAL

Multi-Frequency

Quad Photobeam Detectors

E-964-Q660Q– E-964-Q495Q– 495 ft. (150m) outdoors, 990 ft. (300m) indoors E-964-Q330Q– 330 ft. (100m) outdoors, 660 ft. (200m) indoors E-964-Q165Q– 165 ft. ( 50m) outdoors, 330 ft. (100m) indoors

660 ft. (200m) outdoors, 1320 ft.

(400m) indoors

SECO-LARM

Page 2

ENFORCER Quad-Photobeam Detectors

TABLE OF CONTENTS

Introduction .................................................. 2

Features ....................................................... 2

Overview ....................................................... 3

Wiring Diagram ............................................ 4

Choosing a Location .................................... 4

Running the Cable ...................................... 4

Multiple Sensor Sample Applications .......... 5

Typical Installations ..................................... 5

Wiring the Transmitter – Wall Mount ........... 6

Wiring the Transmitter – Pole Mount ........... 6

Wiring.......................................................... 6

Examples of Ways To Connect Sensors...... 7

Selectable 4-channel Beam Frequency...... 8

Receiver Detail............................................ 8

Beam Alignment T emplate .......................... 8

Beam Alignment ......................................... 9

Adjusting the Response Time ................... 10

T esting the Unit......................................... 10

Specifications ........................................... 1 0

Dimensions ............................................... 11

Troubleshooting ........................................ 11

Introduction:

The ENFORCER E-964-Q Series Quad-Photobeam Sensors are ideal for long-distance protection. Four selectable beam frequencies allow for superior perimeter protection by eliminating crosstalk and interference between multiple units. False alarms created by animals and falling leaves are minimized by the sensor's detection method of all 4 beams simultaneously broken.

The E-964-Q Series of sensors is designed to work in even the most extreme conditions. A built-in heater automatically turns on and off depending on the outside temperature. An environmental control output senses a slow degradation in beam strength when weather conditions worsen preventing false alarms.

Installation and alignment is quick and easy with the ENFORCER E-964-Q Series. The built-in laser and visual alignment systems quickly and easily pinpoint the approximate mounting location for the transmitter and aid in aligning the transmitter and receiver units once mounted. A beam strength indicator clearly displays the strength of the beam at the receiver with 5 LEDs.

Features:

●

Four selectable beam frequencies to eliminate interference between multiple units for enhanced perimeter protection.

●

Audible beam alignment (buzzer).

●

Beam strength indicator (5 LEDs).

●

Environmental Output (Selectable N.O. or N.C.): Signal is sent if a degradation in environmental conditions is detected such as thickening fog to prevent false alarms.

●

Built-in heater.

●

IP-55 ingress protection.

●

Lensed optics reinforce beam strength and provide excellent immunity to false alarms due to rain, snow, mist etc.

●

Automatic input power filtering with special noise rejection circuitry.

●

Voltage testing points for fine tuning the beam alignment.

●

Input voltage: 12-24V AC/DC.

●

Response time adjustable for nearly all situations.

SECO-LARM® U.S.A.

Page 3

Fig. 1: Overview

ENFORCER Quad-Photobeam Detectors

Alignment laser

Vertical

adjustment screw

Green power LED

Power 12~24V AC/DC

Alarm output

Beam strength

indicator (5 LEDs)

Tamper output

On/Off switch for laser

Viewfinder

Horizontal adjustment grip

Red signal LED

NC/NO switch On/Off

Beam channel selection DIP switches

Response time (50ms~700ms)*

Environmental output

}

Voltage output probes

Vertical

adjustment screw

Alignment laser

Heater power

Environmental output

Horizontal adjustment grip

(Receiver shown)

On/Off switch for laser

IMPORTANT – Do not connect to power until the sensor is completely installed and the

installation has been double-checked.

* Factory default 50ms

SECO-LARM® U.S.A.

Viewfinder for alignment

Page 4

ENFORCER Quad-Photobeam Detectors

Fig. 2: Wiring Diagram

Receiver

Power AC/DC

12-24V

(non-polarity)

Alarm O/P

1A @ 125VAC /24VDC

T amper output

N.C. switch

1A @ 30VDC

(Max.)

N.C.

Com

N.O.

Heater

Environmental

output (NO/

NC)

1A @ 125 VAC

/24VDC

Transmitter

Power AC/DC

12-24V

(non-polarity)

T amper output

N.C. switch

1A @ 30VDC

(Max.)

Heater

Choosing a Location

1. Find a suitable location for the receiver within wiring distance of a power supply and the alarm panel.

2. Establish a clear line-of-sight area between the receiver location and the transmitter location.

3. Make sure no trees or vegetation will cause false alarms during windy conditions.

4. Find locations away from standing water that could be splashed on to the receiver or the transmitter.

5. Do not mount the receiver where sunlight or bright lights shine directly into the unit.

6. Install at a distance of 32" to 39" (80 to 100 cm) above the ground for most situations. See fig. 3.

Running the Cable

Run a cable from the alarm control panel to the photobeam sensor. If burying the cable is required, make sure to use electrical conduit. Shielded cable is strongly suggested. See Table 1 for maximum cable length.

Table 1: Cable Length

Model E-964-Q660Q

Wire Size

AWG22 AWG20 AWG18 AWG17

Note (1): Max. cable length when two or more sets are connected is the value shown in Table 1 divided by the no. of sets.

E-964-Q165Q E-964-Q330Q 12V 24V 12V 24V 12V 24V

320m

1,050ft.

550m

1,800ft.

800m

2,600ft.

980m

3,190ft.

2,800m

18,000ft.

4,800m

15,750ft.

7,200m

23,620ft.

8,800m

28,870ft.

280m 920ft.

450m

1,480ft.

700m

2,300ft.

850m

2,790ft.

2,400m 7,870ft.

4,200m

13,780ft.

6,200m

20,340ft.

7,600m

24,930ft.

E-964-Q495Q

200m 660ft.

350m

1,150ft.

500m

1,640ft.

590m

1,940ft.

12V 24V

1,600m 5,250ft.

3,000m 9,840ft.

4,200m

13,780ft.

5,200m

17,060ft.

110m 390ft.

170m 560ft.

250m 820ft.

310m

1,020ft.

SECO-LARM® U.S.A.

900m

2,950ft. 1,400m

4,590ft. 2,200m

7,220ft. 2,600m

8,530ft.

Page 5

3234

ENFORCER Quad-Photobeam Detectors

Multiple sensor sample applications

1. Long distance series application.

Channel #1

Channel #2

Channel #3 Channel #4

2. Two layer (double stacked) applications.

Channel #1

Channel #4 Channel #3 Channel #2

Channel #2 Channel #3

3. Perimeter security applica-

tion.

Channel #3

Channel #1

Channel #2

Channel #4

TxRx

Channel #4

Channel #1

4. Single pair multiple layer application.

Tx Rx

Channel #1

Channel #2

Channel #3

Channel #4

Fig. 3: Typical Installations

Side Views

Top Views

SECO-LARM® U.S.A.

 

32" to 39"



 



 



Page 6

ENFORCER Quad-Photobeam Detectors

Wiring the Transmitter – W all Mount

1. Remove the cover. Remove the screw under the lens unit in order to detach the mounting plate. See fig. 4.

2. If the sensor wiring comes from inside the wall – Break a hole in the mounting plate’s rubber grommet, and pull the cable through the grommet’s hole. Then run the cable through the hole near the bottom of the sensor unit so it comes out the front. Using two of the included mounting screws, attach the mounting plate to the wall. Then reattach the sensor unit to the mounting plate, connect the wires, and snap on the cover. See fig. 5.

3. If the sensor wiring is run along the surface of the wall – There are four plastic knockouts on the back of the sensor unit, two on top and two on bottom. Break out the appropriate knockout, and pull the wiring through the knockout. Then run the wiring through the hole near the bottom of the sensor unit so it comes out the front. Using two of the included mounting screws, attach the mounting plate to the wall. Then reattach the sensor unit to the mounting plate, connect the wires, and snap on the cover. See fig. 6.

Wiring the Transmitter – Pole Mount

(NOTE – Pole mounting bracket included.)

1. Remove the cover. Remove the screw under the lens unit in order to detach the mounting plate. See fig. 4.

2. Break a hole in the mounting plate’s rubber grommet, and pull the cable through the grommet’s hole. Then run the cable through the hole near the bottom of the sensor unit so it comes out the front. Use the included mounting bracket to mount to the pole. Then reattach the sensor unit to the mounting plate, connect the wires, and snap on the cover. See fig. 7.

Wiring (fig. 8)

1. Screw the wires tightly to avoid slipping off the terminals, but not so tight that they break.

2. Screws on terminals which are not used should be tightened.

3. Grounding may be necessary, depending on the location.

Fig. 4: Remove the Transmitter cover

Fig. 5: Wall Mount, Wire from Inside Wall

Fig. 6: Wall Mount, Wire Runs Along Wall

Fig. 7: Pole Mount

– or –

SECO-LARM® U.S.A.

Page 7

ENFORCER Quad-Photobeam Detectors

Fig. 8: Examples of Possible Ways T o Connect One or More Sensors

Example connection 1 -

Standard

➀➁

➀➁➂➃

Tx Rx

Example connection 2 - In-line Single Channel

➀➁ ➀➁➂➃

Example connection 3 - Dual Sensors, Separate Channels

➀➁

➀➁➂➃

➀➁ ➀➁➂➃

➀➁

}

Power N.C. Alarm

}

signal

Control panel

(12~24VAC/VDC)

➀➁➂➃

}

Power N.C. Alarm

}

signal

Control panel

(12~24VAC/VDC)

}

Power N.C. Alarm

}

(ch. 1) N.C. Alarm

}

(ch. 2)

Control panel

(12~24VAC/VDC)

Example connection 4 - Two stacked

➀➁

SECO-LARM® U.S.A.

➀➁➂➃

Ch1

➀➁➂➃

Tx Ch2RxCh2

(12~24VAC/VDC)

}

Power

}

Alarm signal

Control panel

Page 8

ENFORCER Quad-Photobeam Detectors

Selectable 4-channel beam frequency:

The sensor beam frequency can be set at different levels on-site to avoid interference from other photobeam sensors nearby. To select between four different beam frequencies, adjust the beam channel switch of the transmitter side and receiver side. See pg. 3, fig. 1 for switch location and table 2 for switch position.

Fig. 9: Receiver Detail

Table 2: Channel Beam Frequency Selection Chart

CH3

Freq. channel

Switch position

Important

CH1

CH2

– The transmitter and receiver

must be programmed to the same channel.

DIP Switch Channel Selector Beam Alignment Buzzer Switch

Beam Alignment Strength Indicator Switch Response Time Adjustment

CH4

12 12

NO NO

Fig. 10: Included Beam Alignment T emplate:

Use the included SECO-LARM template to aid in aligning the transmitter and receiver.

SECO-LARM® U.S.A.

Page 9

ENFORCER Quad-Photobeam Detectors

Beam Alignment Procedure

1. Remove the sensor cover and turn On the top and bottom lasers of both the transmitter and receiver. There are a total of four lasers.

2. Adjust the transmitter's sensor unit vertically and horizontally until the red dot is centered on the receiver and the receiver’s signal LED turns Off.

3. Repeat step 2 for the receiver then turn Off the lasers.

4. Look through the viewfinder on the transmitter’s lower sensor and adjust it vertically and horizontally until the receiver is clearly seen in the viewfinder.

5. Repeat step 4 for the receiver.

6. Turn On the beam alignment buzzer DIP switch (fig. 9). If the beams are not aligned the buzzer will sound.

7. Cover the top sensor on the receiver with the included template (as shown in fig. 10). Adjust the horizontal angle of the receiver’s lower sensor vertically and horizontally until the buzzer stops sounding. Repeat while covering the lower sensor and adjusting the top sensor.

8. Turn the buzzer Off.

9. Turn On the beam strength Indicator DIP switch (fig. 9). If the beams are not aligned, the indicator will display little or no beam strength, see fig.12.

10.Cover the top sensor on the receiver. Adjust the horizontal angle of the receiver’s lower sensor vertically and horizontally until the beam strength indicator displays a strong signal. Repeat while covering the lower sensor and adjusting the top sensor.

11.Turn the beam strength indicator Off.

Fig. 11: Horizontal and Vertical Sensor Adjustment

Vertical

Adjustment

Screw

The transmitter and receiver sensor units can be adjusted ±15° vertically and ±90° horizontally once the unit is mounted and power is connected.

Horizontal

Adjustment

Finger Grips

View Finder

Fig. 12: Beam Strength Indicator

Strongest

Good

Poor

Bad

No Signal

Fine Tuning

The most accurate way to align the transmitter and receiver is to measure the voltage using the voltage output jack (fig.13).

1. Set the range of a multimeter to 0~10VDC.

2. Insert the red probe into the (+) terminal and the black probe into the (-) terminal.

3. Using Table 3, adjust the receiver’s sensors vertically and horizontally until the best possible voltage output is achieved.

T able. 3: Voltage Output

Voltage Output Alignment Quality

SECO-LARM® U.S.A.

0V <1.1V 1.1~1.4V 1.4~1.7V 1.7~2.0V >2.0V

No Signal Bad Poor OK Good Strongest

Fig. 13: Using a Multimeter for Fine Tuning

Page 10

ENFORCER Quad-Photobeam Detectors

Adjusting the Response Time (IMPORTANT)

1. The response time adjustment knob sets how long the beam can be interrupted before triggering the alarm (see fig.14):

a. A short response time (high sensitivity) is suitable for catching fast

moving intruders, but more susceptible to false alarms.

Fig. 14: Adjusting the Response Time

(300ms)

b. A long response time (low sensitivity) reduces false alarms, but fast

moving intruders may not trigger the sensor.

2. Adjust the knob to the site’s situation. You may need to make adjustments later after the walk-through test.

IMPORTANT: Note that the response time is set at the factory to the shortest time (50ms). After installation is complete, please adjust to

best suit the site situation.

700ms50ms

Testing the Unit

1. Power up the transmitter and receiver.

2. If the red alarm LED remains steady ON even when the beam is not interrupted, re-adjust the alignment.

3. Walk between the transmitter and receiver to interrupt the beams. Walk at various speeds, and adjust the delay time adjustment knob as needed.

T able 4: Specifications

Model Max. range (outdoor) Max. range (indoor) Current (Tx & Rx) Current (Tx & Rx & heaters) Input voltage Response time Detection method Selectable beam frequencies Alarm output Tamper output (Tx & Rx) Environmental output Beam-strength indicator Signal LED (Rx) Power LED (Tx & Rx) Laser wavelength Laser output power Alignment angle Operating temperature Weight Ingress protection Case Dimensions

* This is the minimum time interval between breaking of both beams which will trigger the output. Setting the interval longer will

reduce false alarms from birds or falling leaves, etc., while setting it shorter will detect faster moving objects.

E-964-Q165Q

165' (50m) 330’ (100m) 110mA 260mA 12~24 VAC/VDC (non-polarity) 50ms~700ms (variable, factory default 50ms) All 4 beams simultaneously broken Four (4) channels Form "C" relay COM/N.O./N.C. 1A@125VAC/24VDC NC switch, 1A@120VAC Selectable N.O. or N.C. 1A@125VAC/24VDC 5 LEDs indicate signal strength from high to low Red LED ON Green LED - illuminated when power is on 650nm

≤

5mW

Horizontal: ±90

-13~1310F (-250~ 550C)

5.7 lbs. (2.6kg) IP55 PC Resin

/4" x 47/16" x 45/16" (387 x 113 x 110mm)

NOTE – The alarm will be triggered only if both the upper and lower beams are simultaneously interrupted.

IMPORTANT – Test the detector periodically to ensure the alignment and delay time settings are suitable for the site.

E-964-Q330Q

330’ (100m) 660’ (200m) 115mA 270mA

E-964-Q495Q

495’ (150m) 990’ (300m) 120mA 280mA

E-964-Q660Q

660’ (200m) 1320’ (400m) 125mA 290mA

beam is broken or Tx and Rx out of alignment

Vertical: ±15

SECO-LARM

U.S.A.

Page 11

Fig. 15: Dimensions

Upper

View

43ST Pole Size

Side View

ENFORCER Quad-Photobeam Detectors

411/32”

(110mm)

47/16”

(113mm)

” (367mm)

Front View

Rear View

Troubleshooting:

Transmitter LED not lit

_________________________________________________________________________________________________________________________________

Receiver LED does not light when interrupted

_________________________________________________________________________________________________________________________________

Beams are interrupted and LED lights, but the alarm does not trigger.

_________________________________________________________________________________________________________________________________

Signal LED continuously lit

_________________________________________________________________________________________________________________________________

Alarm trigger becomes erratic in bad weather

_________________________________________________________________________________________________________________________________

Frequent false alarm triggers

SECO-LARM® U.S.A.

Make sure the input power to the transmitter is 12 to 24 VAC/VDC.

Check the input power to the receiver is 12 to 24 VAC/VDC.

Check the continuity of the wiring from the receiver to the alarm.

Clear any obstacles between the transmitter and receiver. Clean the lenses of both units.

Check overall system installation. Realign the lenses.

Adjust the response time. Change location of transmitter and receiver.

Page 12

ENFORCER Quad-Photobeam Detectors

Also available from SECO-LARM:

E-960-D290Q

E-932-D33TBQ

E-9622-4B25

Twin Photobeam

Detectors

Range: up to 290' outdoors.

•

Lensed optics reinforce beam

•

strength and provide excellent immunity to false alarms due to rain, snow, mist, etc.

Weatherproof, sunlight filtering case

•

for indoor and outdoor conditions. Quick easy installation with built-in

•

laser-beam alignment system.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in

normal service for three (3) years from the date of sale to the original customer. SECOLARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECOLARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECOLARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECOLARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only , at SECOLARM’s option. In no event shall SECOLARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

NOTICE:

reserves the right to change specifications without notice. SECOLARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2019 SECOLARM U.S.A., Inc. All rights reserved.

The

SECO-LARM policy is one of continual development and improvement. For that reason, SECOLARM

Flush-Mount Photobeam

Sensors

E-932-D33TBQ – Photoelectric

• Through-Beam Sensor.

Suitable for entrances, hallways,

• room in office or home.

Fits single-gang box.

• Adjustable alignment angle from

•

horizonatally / vertically.

+/-15

Curtain / Barrier Sensors

Available in 4, 6, 8 or 10 beams.

• Range: 25 ft. outdoor,

•

50 ft. indoor. Slim-line design 7/8" x 15/16". Weatherproof IP65 construction. Triggers on breaking of any

single or 2 adjacent beams (programmable).

SECO-LARM's ENFORCER Twin Photobeam detector series are protected by the following patents: U.S. pat. no. D485774 ; T aiwan pat. no. 89463 ; China pat. no. ZL0331103.0 Other international patents are pending.

SECO-LARM

16842 Millikan Avenue, Irvine, CA 92606 Phone: (949) 261-2999 (800) 662-0800

U.S.A., Inc.

Website: www.seco-larm.com E-mail: sales@seco-larm.com

MI_E-964-QxxxQ_190531.pmd

PITSW3