Seco-Larm EB-P101-20Q, EB-P101-01Q User Manual

Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Installation Manual
Passive Video Baluns
EB-P101-01Q
Passive Video Balun
EB-P101-20Q
Passive Video Balun with 6” Pigtail
ENFORCER Passive Video Baluns
BNC
Connector
9
/16”
(15mm)
4
(102mm)
2
(51mm)
13/16”
(30mm)
EB-P101-01Q
9
/16” (15mm)
Screwless
terminal blocks
113/16” (46mm)
9
/16”
(15mm)
EB-P101-20Q
9
/16”
(15mm)
Screwless
terminal blocks
Overview:
Specifications:
Model
EB-P101-01Q
EB-P101-20Q
Video
Range* B/W
1,950’ (600m)
Color
1,300’ (400m)
Video format
NTSC, PAL, SECAM
Maximum input
1.1Vp-p
Insertion loss
<2dB per pair from DC~6MHz
Return loss
>15dB from DC~6MHz
Frequency response
DC~6MHz
Common mode rejection
>40dB, 15kHz~6MHz
Connections
Wire type
UTP (Unshielded Twisted Pair) 24~16 AWG
Wire category
Cat2~Cat6
UTP Connection
Silver plated
Attenuation
DC~6MHz, 6.6dB max.
Impedence Coax, male BNC
75Ω@1MHz
Terminal block
100Ω@1MHz
Other
DC Loop resistance
52Ω/1000’ (52Ω/305m)
Differential capacitance
19pF/ft max. (62pF/m max.)
Power
No power required
Operating temperature
32 ~131 F (0 ~55 C)
Storage temperature
-4 ~158 F (-20 ~70 C)
Humidity range
0~95 % (Non-condensing)
Case
ABS Plastic
Weight
1.4-oz (40g)
Cable length
N/A
6” (153mm)
Dimensions
113/16”x9/16”x9/16”
(46x15x15 mm)
13/16”x9/16”x9/16”
(30x15x15 mm) Housing only
Parts List:
EB-P101-01Q
10 x Passive video baluns
1 x Manual
EB-P101-20Q
10 x Passive video baluns with 6” pigtail
1 x Manual
*Shorter range may result when used with a DVR.
BNC
Connector
2 SECO-LARM U.S.A., Inc.
Installation:
1. Video baluns are connected in pairs. Connect one balun to the CCTV camera. Connect
another balun to a DVR or other remote device.
2. Make sure the distance between the camera and the remote video device does not exceed
1,950ft (600m) for black and white video or 1,300ft (400m) for color video.
3. Run Cat5e/6 cable (UTP) from the remote video device to the camera.
4. Connect the Cat5e/6 cable to both baluns. NOTE: Video baluns are polarity-sensitive. a. Strip approximately
1
/4” (6mm) of insulation from the same two wires at both ends of a
Cat5e/6 cable.
b. Push down the small tabs above the terminals. Insert each wire into each terminal at both
ends of the cable. After the wires have been inserted into the terminals, there should be no bare wire showing.
5. Connect the video baluns into the BNC connector of the CCTV camera and the remote
video device.
6. Test the connection by powering up the CCTV camera and remote video device to make sure
they operate as expected.
Sample Applications:
Single Pair of Passive Video Baluns
ENFORCER
Bullet Camera
Cat5e/6 Cable
Color: Up to 1,300ft (400m) B/W: Up to 1,950ft (600m)
1
/4” (6mm)
Leave no
wires exposed
Remote
DVR, Monitor, Switch, etc.
Note: Shorter range may result when used with a DVR.
Multiple CCTV Cameras Over a Single Cat5e/6 Cable
Cat5e/6 Cable
Color: Up to 1,300ft (400m) B/W: Up to 1,950ft (600m)
ENFORCER
Bullet Camera
Passive Video Baluns
connected to a DVR
ENFORCER
Dome Camera
Elite 3X
Dome Camera
Elite 3X
Bullet Camera
Small size allows multiple baluns to
be mounted to the
back of a DVR.
Note: Shorter range may result when used with a DVR.
ENFORCER Passive Video Baluns
SECO-LARM U.S.A., Inc. 3
ENFORCER Passive Video Baluns
Wavy or ghost image if connected to image processor (e.g., multiplexer or DVR), but not if directly to monitor.
Move the Cat5e/6 cable away from possible sources of interference. Ensure that the same twisted pair connects to a balun at both ends of the cable. Replace the cable with a new Cat5e/6 cable.
Image background flutters between dark and light.
Remove a local power source, or adjust the monitor’s brightness and contrast.
Image is wavy and shakes.
Try reversing polarity of the two wires at one end of the Cat5e/6 cable.
Image is weak or faded.
Reduce the Cat5e/6 cable length. Replace with a higher-grade cable. Cat5e cable meets the specifications in the
manual. Cat6 cable allows longer range.
No image.
Double-check that the Cat5e/6 and BNC cables are connected properly. Run a continuity test on all wires in the cable. Check that the camera and monitor are powered up.
MiEB-P101-xxQ_1211.docx
PICFN1
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
WARNING
Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock, damage the device, and void the warranty. Do not open the case of this device, as there are no field-serviceable components inside.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
Website: www.seco-larm.com E-mail: sales@seco-larm.com
Troubleshooting:
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for two (2) years from the date of sale
to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
Also Available from SECO-LARM:
4-Channel Passive
Video Transceiver
16-Channel Passive
Video Transceiver
Active Video Baluns
(Single or Hub)
Passive Video, Power,
and Data Balun
Weatherproof Passive
Video Balun
Passive Video Balun with
Ground Loop Isolator
4 SECO-LARM U.S.A., Inc.
Loading...