Seco-Larm E-964-D390Q, E-960-D90Q, E-960-D190Q User Manual

Also Available from SECO-LARM:

Quad Photobeam

Detectors

• 4 Models available - up to 660
ft. (200m) range.

• Weatherproof

• 12~24 VAC/VDC

• Laser-beam alignment

Reective

Photobeam Sensor

Curtain Sensors

• 2, 4, 6, 8, or 10 Beams available

• Up to 50ft (15m) range

• Weatherproof

• Slimline design

• Laser-beam alignment

Hooded Reective

Photobeam Sensors

Long-Range

Barrier Sensors

Twin Photobeam Detectors

Manual

• 2, 4, 6, or 8 Beams available

• Up to 393ft (120m) range

• Weatherproof

• Multi-frequency

• Adjustable interruption time

Flush-Mount

Photobeam Sensors

• Available with 45ft (14m) or
35ft (11m) range

• Weatherproof

• Mounting hardware included

• Reflector included

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to
the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair,
or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.

SECO-LARM® U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Tel: [phone] Fax: [phone]

• Available with 50ft (15m) range or
33ft (10m) range

• Weatherproof

• Polarized version available

• Round reflector included

12

• Available with reflective beam and
16ft (5m) range or through-beam
and 33ft (10m) range

• Adjustable alignment angle

• Mounts to a single-gang box

file:DTP\Manual\MiE96x-DxxxQ_P1305.pmd

Website: www.seco-larm.com
E-mail: sales

@

seco-larm.com

PITSW3

Model # Outdoor Range Indoor Range
E-964-D390Q* 390 ft. (120m) 790 ft. (240m)
E-960-D290Q 290 ft. (90m) 590 ft. (180m)
E-960-D190Q 190 ft. (60m) 390 ft. (120m)
E-960-D90Q 90 ft. (30m) 190 ft. (60m)

* Multi-frequency version

SECO-LARM

Note: Products with model numbers that end with "Q" or that have a round green"Q"sticker are RoHS compliant.

®

®

TABLE OF CONTENTS

Important ......................................................... 2

Choosing a Location........................................ 3

Typical Installations ....................................... 4

Running the Cable ........................................... 4

Wiring the Transmitter – Wall Mount ............... 4

Wiring the Transmitter – Pole Mount ................ 5

Wiring ............................................................. 5

Examples of Ways To Connect Sensors ............ 6

Selectable 4-channel Beam Frequency ............ 7

Beam Frequency Selection Chart ..................... 7

(E-964-D390Q Model Only)

Multiple Sensors Sample Applications

Adjusting the Alignment ................................. 9

Adjusting the Delay Time ............................... 10

Testing the Unit ............................................. 10

Specifications ............................................... 10

Dimensions ................................................... 11

Troubleshooting ............................................. 11

.......... 7-8

Fig. 12: Dimensions

Upper View

43ST Pole Size

2.8” (72mm)

2.9” (74mm)

6.8” (173mm)

Features:

l

Four selectable beam frequencies
(For E-964-D390Q model only).

l

Twin beams provide reliable perimeter
security,

minimizing false alarms from

falling leaves, birds, etc.

l

Lensed optics reinforce beam strength
and provide excellent immunity to false
alarms due to rain, snow, mist, etc.

l

Weatherproof, sunlight-ltering case for
indoor and outdoor use.

l

Non-polarized power inputs.

l

Automatically adjusts beam strength
to compensate for different weather

conditions

l

Automatic input power ltering with
special noise rejection circuitry.

l

N.C./N.O. alarm output.

l

N.C. tamper circuit included.

l

Quick, easy installation with built-in
laser beam alignment system.

l

Interruption time adjustable for nearly
all situations.

Included:

Transmitter x 1 Receiver x 1 Mounting plates x 2

Pole mounting

brackets (2 sets)

Mounting
hardware

also includ-

ed.

Side View

Table 6: Troubleshooting

Situation

Transmitter LED does not light.

Receiver LED never lights up
when the beam is interrupted.

Beams interrupted and LED
lights, but no alarm trigger.

Alarm LED continuously lit.

Alarm trigger becomes erratic
in bad weather.

Frequent false triggers from
leaves, birds, etc.

Front View

Possible Problem

Incorrectly wired and/or
insufcient voltage

a. Insufcient voltage
b. Beam reected away from receiver
c. Beams not simultaneously interrupted.

Alarm trigger cable may be cut, or the
relay contact stuck due to overloading.

a. Lenses out of alignment.
b. Beams are blocked.
c. Cover is foggy or dirty.

Lenses out of alignment.

a. Too sensitive.
b. Bad location.

Rear View

Solution

Ensure the power supply to the
transmitter is 12 to 24 VAC/VDC.

a. Double-check the voltage.
b. Clean the cover.
c. Check overall installation.

Check the continuity of the wiring
between the sensor and the alarm.

a. Realign the lenses.
b. Remove any obstacles.
c. Clean the cover.

Check overall system installation.
If still erratic, realign the lenses.

a. Reduce the response time.
b. Change the transmitter and/or
location.

IMPORTANT

–

Do not connect to power until the sensor is completely installed and

the installation has been double-checked.

2

11