Seco-Larm E-960-D390, E-960-D290, E-960-D190, E-960-D90 Installation Manual

Download

Page 1



ENFORCER

Twin Photobeam Detectors

E-960-D390 E-960-D290 E-960-D190 E-960-D90

INSTALLATION MANUAL

Features:

 Range — E-960-D390 — 390 ft. (120m) outdoors, 790 ft. (240m) indoors

— E-960-D290 — 290 ft. (90m) outdoors, 590 ft. (180m) indoors — E-960-D190 — 190 ft. (60m) outdoors, 390 ft. (120m) indoors — E-960-D90 — 90 ft. (30m) outdoors, 190 ft. (60m) indoors

●

Twin beams provide reliable perimeter security, falling leaves, birds, etc.

●

Lensed optics reinforce beam strength and provide excellent immunity to false alarms due to rain, snow, mist, etc.

●

Weatherproof, sunlight-filtering case for indoor and outdoor use.

●

Anti-frost system so that beam functions even in extreme conditions.

minimizing false alarms from

●

Automatic input power filtering with special noise rejection circuitry.

●

N.C./N.O. alarm output.

●

N.C. tamper circuit included.

●

Non-polarized power inputs.

●

Quick, easy installation with built-in laser beam alignment system.

●

Interruption time adjustable for nearly all situations.

Included:

Transmitter x 1 Receiver x 1 Mounting plates x 2

Mounting hardware

also

included.

Pole mounting

brackets (2 sets)

Page 2

TABLE OF CONTENTS

Important ................................................... 2

Examples of Ways To Connect Sensors ............. 5

Choosing a Location ................................... 2

Typical Installations ....................................... 3

Running the Cable ........................................... 3

Wiring the Transmitter – Wall Mount ................ 4

Wiring the Transmitter – Pole Mount ................ 4

Wiring .............................................................. 5

Fig. 1: Identifying the Sensors

Delay time

adjustment

knob

Signal LED

Alarm LED

Power LED

Voltage

Output Probes

Receiver Transmitter Mounting Plate

Power LED

Vertical adjustment

Horizontal

adjustment

View finder

Mounting laser

Laser ON/OFF switch

Adjusting the Alignment ................................... 6

Adjusting the Delay Time ................................. 6

Testing the Unit ................................................ 7

Specifications .................................................. 7

Dimensions ..................................................... 8

Troubleshooting ............................................... 8

Terminals

screw

Lens

Important

Do not connect to power until the sensor is completely installed and the installation has been double-checked.

Choose a Location

To prevent erratic operation and/or false alarms:

• Wind will not directly cause false alarms, but could cause leaves or similar objects to fly or wave into the beams. Therefore, do not mount near trees, bushes, or other leafy vegetation.

• Do not mount where the transmitter or receiver could be splashed by water or mud.

• Do not mount where the unit could be suddenly exposed to a bright light, such as a floodlight or a passing automobile’s headlight.

• Do not let sunlight or any direct beam of light enter the sensing spot of the transmitter. If needed, mount so the receiver, not the transmitter, faces the sun.

• Do not mount where animals could break the beams.

Page 3

Fig. 2: Vertical and Horizontal Adjustments Fig. 3:Typical Installations

Vertical adjustment

±5° (10°)

adjustment

Horizontal adjustment

±90°(180°)

Vertical

screw

Side Views

©©© ©©©

32" to 39"

Top Views

©©©

©©© ©©©

©©©©©©©©

©©© ©©©

©©©©

Typical Installations

The photoelectric beam lens can be adjusted horizontally ±90°, and vertically ±5° (see fig. 2). This allows much flexibility in terms of how the transmitter and receiver can be mounted. See fig. 3.

Install at a distance of 32” to 39” (80 to 100 cm) above the ground for most situations. See fig. 3.

Running the Cable

Run a cable from the alarm control panel to the photobeam sensor. If burying the cable is required, make sure to use electrical conduit. Shielded cable is strongly suggested. See Table 1 for maximum cable length.

Table 1: Cable Length

Model E-960-D390

Wire Size

AWG22

0.33mm

0.0005in AWG20

0.52mm

0.0008in AWG18

0.83mm

0.0013in AWG17

1.03mm

0.0016in

Note (1):

Note (2):

E-960-D90 E-960-D190

12V 24V 12V 24V 12V 24V

320m

1,050 ft.

550m

1,800 ft.

800m

2,600 ft.

980m

3,190 ft.

2,800m

18,000 ft.

4,800m

15,750 ft.

7,200m

23,620 ft.

8,800m

28,870 ft.

280m

920 ft.

450m

1,480 ft.

700m

2,300 ft.

850m

2,790 ft.

2,400m

7,870 ft.

4,200m

13,780 ft.

6,200m

20,340 ft.

7,600m

24,930 ft.

Max. cable length when two or more sets are connected is the value shown in Table 1 divided by the number of sets.

The power line can be wired to a distance of up to 3,300 ft. (1,000m) with AWG22 (0.33mm2) telephone wire.

E-960-D290

110m

390 ft.

170m

560 ft.

250m

820 ft.

310m

1,020 ft.

900m

2,950 ft.

1,400m

4,590 ft.

2,200m

7,220 ft.

2,600m

8,530 ft.

12V 24V

200m

660 ft.

350m

1,150 ft.

500m

1,640 ft.

590m

1,940 ft.

1,600m

5,250 ft.

3,000m

9,840 ft.

4,200m

13,780 ft.

5,200m

17,060 ft.

Page 4

Wiring the Transmitter – Wall Mount

1. Remove the cover. Remove the screw under the lens unit in order to detach the mounting plate. See fig. 4.

2. If the sensor wiring comes from inside the wall – Break a hole in the mounting plate’s rubber grommet, and pull the cable through the grommet’s hole. Then run the cable through the hole near the top of the sensor unit so it comes out the front. Using two of the included mounting screws, attach the mounting plate to the wall. Then reattach the sensor unit to the mounting plate, connect the wires, and snap on the cover. See fig. 5.

3. If the sensor wiring is run along the surface of the wall – There are two plastic knockouts on the back of the sensor unit, one on top and one on bottom. Break out the appropriate knockout, and pull the wiring through the knockout. Then run the wiring through the hole near the top of the sensor unit so it comes out the front. Using two of the included mounting screws, attach the mounting plate to the wall. Then reattach the sensor unit to the mounting plate, connect the wires, and snap on the cover. See fig. 6.

Fig. 4: Remove the Transmitter cover

Fig. 5: Wall Mount, Wire from Inside Wall

Fig. 6: Wall Mount, Wire Runs Along Wall

Wiring the Transmitter – Pole Mount

(NOTE – Pole mounting bracket required.)

1. Remove the cover. Remove the screw under the lens unit in order to detach the mounting plate. See fig. 4.

2. Break a hole in the mounting plate’s rubber grommet, and pull the cable through the grommet’s hole. Then run the cable through the hole near the top of the sensor unit so it comes out the front. Use the included mounting bracket to mount to the pole. Then reattach the sensor unit to the mounting plate, connect the wires, and snap on the cover. See fig. 7.

– or –

Fig. 7: Pole Mount

Page 5

Wiring (fig. 8)

1. Screw the wires tightly to avoid slipping off the terminals, but not so tight that they break.

2. Screws on terminals which are not used should be tightened.

3. Grounding may be necessary, depending on the location.

Fig. 9: Examples of Possible Ways To Connect One or More Sensors

Example connection 1 - Standard

Fig. 8: Wiring

Transmitter

{

Power

10 - 30VDC (non-polarity)

Receiver

1234567

COM ON

{

Power

10 - 30VDC (non-polarity)

Alarm

NC NC

{

Alarm output

120V (AC/DC) 1A

Control panel

(12VDC)

}

Pow er

}

Alarm signal

{

Tamper output N.C. switch 120V (AC/DC) 1A (Triggers if cover detached)

{

Tamper output N.C. switch 120V (AC/DC) 1A (Triggers if cover detached)

➀➁

Transmitter

Example connection 2 - Dual Sensors, Separate Channels

➀➁ ➀➁➂➃

Transmitter

Example connection 3 - In-line Single Channel

➀➁

Transmitter

➀➁➂➃

Receiver

➀➁➂➃

Receiver

➀➁ ➀➁➂➃

Transmitter

➀➁

Transmitter

Receiver

➀➁➂➃

Receiver

Control panel

(12VDC)

}

Pow er

}

Alarm (ch. 1)

}

Alarm (ch. 2)

Control panel

(12VDC)

}

Pow er

}

Alarm signal

Page 6

Adjusting the Alignment

The transmitter and receiver sensor units can be adjusted ±5º vertically and ±90º horizontally once the unit is mounted and power is connected. See fig. 2.

There are two ways to adjust alignment:

1. Laser adjustment (see fig. 1):

Fig. 10: Horizontal and Vertical Sensor Adjustment

Vertical

Adjustment

Horizontal

Adjustment

a. Remove the transmitter cover, then turn the laser on with

the ON/OFF switch (see fig. 1). A red dot will show where the photoelectric beams are aimed.

b. Adjust the transmitter's sensor unit vertically and

horizontally until the red dot is centered on the receiver and both the receiver’s LEDs turn off. See Table 2. It may be necessary to adjust the horizontal and vertical angle

View

Finders

of the receiver's sensor unit as well.

c. Repeat steps a and b for the receiver.

d. Turn the lasers off, and then replace the covers.

WARNING: Do not look directly at the lasers.

2. Eyeball adjustment (see fig.10): a. Remove the transmitter cover, and look into one of

the alignment viewfinders (one of the four holes located between the two lenses) at a 45° angle.

b. Adjust the horizontal angle of the lens vertically

and horizontally until the receiver is clearly seen in the viewfinder.

c. Repeat steps a and b for the receiver.

d. Replace the transmitter and receiver covers.

NOTE - If you cannot see the opposite unit in the viewfinder, put a sheet of white paper near the unit to be seen, move your eyes about 2" (5cm) away from the viewfinder, and try again.

Table 2: Receiver LED Indicators

Alarm and signal LEDs Two LEDs OFF One LED ON Two LEDs ON

Signal strength Best Good Re-adjust

Fine Tuning the Receiver

1. Once the sensor is mounted and aligned, the sensor can be fine tuned using the voltage output jack.

a. Set the range of a volt-ohm meter (VOM) to

0~10VDC.

b. Insert the red (+) probe into the (+) terminal

and the black (-) probe into the (-) terminal.

c. Measure the voltage (see table 3). d. Adjust the horizontal angle by hand until the

VOM indicates the highest voltage.

e. Adjust the vertical angle by turning the vertical

Table 3:

Voltage output 5~8 V

2.5~5V

1.5~2.5 <1.5

adjustment screw until the VOM indicates the highest voltage.

NOTE - Do not interrupt the beam while adjusting alignment.

Alignment quality Best Good Fair

Re-adjust

Note: 8VDC is maximum

possible reading.

Page 7

Adjusting the Delay Time

1. The delay time adjustment knob sets how long the beam can be interrupted before triggering the alarm (see fig. 11):

a. A short interrupt time (high sensitivity) is suitable for catching fast moving

intruders, but more susceptible to false alarms.

b. A long interrupt time (low sensitivity) reduces false alarms, but fast

moving intruders may not trigger the sensor.

2. Adjust the knob to the site’s situation. You may need to make adjustments later after the walk-through test.

Testing the Unit

1. Power up the transmitter and receiver.

2. If the yellow or red LED remains steady ON even when the beam is not interrupted, readjust the alignment.

3. Walk between the transmitter and receiver to interrupt the beams. Walk at various speeds, and adjust the delay time adjustment knob as needed.

Table 4: Specifications

NOTE – The alarm will be triggered only if both the upper and lower beams are simultaneously interrupted.

IMPORTANT – Test the detector periodically to ensure the alignment and delay time settings are suitable for the site.

Fig. 11: Adjusting the Delay Time

(300ms)

700ms50ms

Model Max. range (outdoor) Max. range (indoor) Current Power Detection method Interrupt speed* Alarm output Tamper output (Tx & Rx) Alarm LED (receiver) Signal LED (receiver) Power LED (transmitter and receiver) Laser wavelength Laser output power Alignment angle Operating temperature Weight Case

*This is the minimum time interval between breaking of both beams which will trigger the output. Setting the interval longer will reduce false alarms from birds or falling leaves, etc., while setting it shorter will detect faster moving objects.

E-960-D90 90’ (30m) 190’ (60m) 36mA

E-960-D190 190’ (60m) 390’ (120m) 42mA

E-960-D290 290’ (90m) 590’ (180m)

50mA 10~30VDC (non-polarized) Simultaneous breaking of 2 beams 50msec~700msec (variable) NO/NC relay, 1A @ 120VAC NC switch, 1A @ 120VAC Red LED - ON: When transmitter and receiver are not aligned or when beam is broken. Yellow LED - ON: When receiver's signal is weak or when beam is broken. Green LED ON: Indicates connected to power 650nm ≤5mW Horizontal: ±900, Vertical: ±5

-130F (-250C) to +1310F (+550C)

2.5 lbs. (1.1kg) PC Resin

E-960-D390 390’ (120m) 790’ (240m) 58mA

Page 8

Fig. 12: Dimensions

Upper View

43ST Pole Size

Side View

Table 5: Troubleshooting

Trouble

Transmitter LED does not light.

Receiver LED never lights up when the beam is interrupted.

Beams interrupted and LED lights, but no alarm trigger.

Alarm LED continuously lit.

Alarm trigger becomes erratic in bad weather.

Frequent false triggers from leaves, birds, etc.

2.8” (72mm)

2.9” (74mm)

6.8” (173mm)

Front View

Possible Origin(s)

Incorrectly wired and/or

Incorrectly wired and/or insufficient voltage

insufficient voltage

a. Insufficient voltage

a. Insufficient voltage b. Beam reflected away from receiver

b. Beam reflected away from receiver c. Beams not simultaneously interrupted.

c. Beams not simultaneously interrupted.

Alarm trigger cable may be cut, or the

Alarm trigger cable may be cut, or the relay contact stuck due to overloading.

relay contact stuck due to overloading.

a. Lenses out of alignment.

a. Lenses out of alignment. b. Beams are blocked.

b. Beams are blocked. c. Cover is foggy or dirty.

c. Cover is foggy or dirty.

Lenses out of alignment.

a. Too sensitive.

a. Too sensitive. b. Bad location.

b. Bad location.

Rear View

Remedy(s)

Ensure the power supply to the transmitter is 10 to 30 VDC.

a. Double-check the voltage. b. Clean the cover. c. Check overall installation.

Check the continuity of the wiring between the sensor and the alarm.

a. Realign the lenses. b. Remove any obstacles. c. Clean the cover.

Check overall system installation. If still erratic, realign the lenses.

a. Reduce the response time. b. Change the transmitter and/or location.

SECO-LARM® U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

SECO-LARM's policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. Copyright © 2002 SECO-LARM® U.S.A., Inc. All rights reserved.

file:TwinbeamIMU2.P65