SECO-LARM E-941DA-1K2P User Manual

ELECTROMAGNETIC LOCK Installation ManualELECTROMAGNETIC LOCK Installation Manual

Installation Manual

TROUBLESHOOTING

Problem:

• Door does not lock

• Status LED is not
illuminated

Door locks, but can be
easily forced open

Delay in door
releasing

No relay output

Delay in door relocking

Possible cause:

No power

Poor contact between
electromagnet and armature
plate

Incorrect voltage setting

• A secondary diode was
installed across the
electromagnet

• No power

• Misalignment

• Check timer

Solutions:

• Check to make sure the wires are securely tightened to
the terminal block.

• Check that the power supply is connected and operating.

• Make sure the lock switch is wired correctly.

• Make sure the electromagnet and armature plate are
properly aligned.

• Make sure the contact surfaces of the electromagnet and
armature plate are clean and free from rust.

• Check the power leads with a meter, and make sure
12VDC or 24VDC is present.

• The electromagnet is fitted with a metal oxide varistor to
prevent interference, so do not install a secondary diode.

• Check that the power is connected and operating.

• Make sure the lock is aligned properly.

• Make sure the NO/NC/COM are wired properly.

• Make sure timer is adjusted to desired delay time.

REGULAR MAINTENANCE

• Clean the contact surfaces of the electromagnet or armature plate with a soft cloth and non-abrasive, non­corrosive cleaner.

• Apply a light coat of a silicon lubricant to prevent rust. Wipe away the excess.

• Check that the armature plate is securely attached to the door, yet can pivot slightly around the armature screw.

• Check that the electromagnet is securely attached to the door frame.

WARRANTY:

material and workmanship while used in normal service for a period of one (1) year from the
date of sale to the original customer. Our obligation is limited to the repair or replacement of any
defective part if the unit is returned, transportation pre-paid, to SECO-LARM.

ENFORCER Electromagnetic Locks are warranted against defects in

NOTICE

The information and specifications printed in this manual are current at the time of publication.
However, the SECO-LARM policy is one of continual development and improvement. For this
reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is
also not responsible for misprints or typographical errors.

Copyright © 2003 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be
reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

SECO-LARMSECO-LARM

SECO-LARM

SECO-LARMSECO-LARM
16842 Millikan Avenue, Irvine, CA 92606

Tel: [phone] Fax: [phone]

®

U.S.A., Inc. U.S.A., Inc.

U.S.A., Inc.

U.S.A., Inc. U.S.A., Inc.

Website: www.seco-larm.com
E-mail: sales

@

seco-larm.com

SECO-LARM U.S.A., Inc.Page 4

PITGW1

E941SA1K2PD.pmd

®

ENF ORCER

E-941S A-1K2PD

1200 Pound Holding Force Electromagnetic
Lock with status sensor, LED status display
and adjustable time delay.

Also available:

E-941DA-1K2P

E-941SA-1200
E-941SA-600
E-941SA-300

HOW IT WORKS

When power is applied to the magnetic lock, it turns on the unit's powerful built-in electromagnet. This electromagnet is
attracted to the steel armature plate which is mounted on a door, holding the door fast against unauthorized entry. When
power to the magnetic lock is turned off, the electromagnet releases the armature plate, allowing the door to open. In
addition, the E-941SA-1K2PD has built-in LEDs to show electromagnet status, plus a status sensor to monitor whether the
door is securely closed, and a built-in adjustable-delay locking timer.

SPECIFICATIONS

Power

Magnet Size

Armature Size

Holding Force

Status Sensor

Status LED (2-Color)

Timer Delay

Current Drain

Voltage Tolerance

Housing

Temperature

Weight

-

Double-door 1200 lb. maglock with status
sensor and LED

-

1200 lb. maglock without status sensor

-

600 lb. maglock without status sensor

-

300 lb. maglock without status sensor

E-941SA-1K2PD

12VDC/24VDC

5

/8 x 25/8 in. (268 x 42 x 67 mm)

10½ x 1

1

/4 x 5/8 x 23/8 in. (185 x 16 x 61 mm)

7

1200 lb. (545kg)

Relay, 3A @ 12VDC

Locked - Green, Unlocked - Red

1~78 seconds

500mA @ 12VDC, 250mA @ 24VDC

± 10%

Aluminum

14° ~ 131°F (-10° ~ 55°C)

11 lbs. (5.0 kg)

Page 1

ELECTROMAGNETIC LOCK Installation ManualELECTROMAGNETIC LOCK Installation Manual

+

Status Sensor Output

N.O.

-

SPDT rated 3A @ 12VDC

}

Control
Device

Power

Supply

ENFORCER

+

-

Relay

Status LED*

Timer

Adjust

COM

N.C.

Voltage
Selection
Jumpers

Filler
Plate*

Standard
Mounting

"Z"
Bracket

For Inswing Doors

"L" Bracket

* Note: may require more

than one filler plate.

Sexnut tube

Sexnut
bolt

This side drill
16mm only

Drill a 8mm
hole thru door

Armature
Screw

Steel and
Rubber
washers
(as
needed)

Armature

HOLLOW METAL DOOR

Drill an 8mm hole thru door. From sexnut
bolt side only, enlarge the 8mm hole to
16mm.

Drill an 8mm hole thru door. From sexnut
bolt side of door, drill 12.7mm (1/2") hole,
25mm in depth.

Drill a 6.8mm dia. hole and tap for
M8 x 1.25 thread.

Sexnut
bolt

Dr ill 12.7mm
(1/2")

Drill a 8mm
hole thru door

Armature
Screw

Armature

SOLID CORE DOOR

Armature Screw

Tap M8 x 1.25 Thread

REINFORCED DOOR

Armature

Steel and
Rubber washers
(as needed)

Steel and
Rubber washers
(as needed)

MOUNTING THE E-941SA-1K2PD

A. Drill holes for the mounting plate and

armature plate (see fig. 1 and 2) by
doing the following:

1. Fold the mounting template along
the dotted line.

2. Close the door. Find a mounting
location on the door frame near the
upper free-moving corner of the
door, as close to the corner of the
door frame as possible.

3. Place the template against the door
and frame.

4. Drill two holes in the door frame and
three holes in the door as indicated
on the template.

NOTE — A filler plate or an L-bracket or
Z-bracket (optional) may be required for
the electromagnet, depending on the door
frame. See fig. 1.

B. Mount the armature plate to the door

using at least two steel and one rubber
washer (fig. 2):

NOTE — Actual installation varies
according to door style.

1. Put one rubber washer between two
steel washers, and place them over
the armature screw between the
armature plate and the door. This
will allow the armature plate to
pivot slightly around the armature
screw in order to compensate for
door misalignment.

2. Tighten the sexnut bolt enough so
the armature plate can withstand

3. Do not tighten the armature plate

the force of someone attempting to
break down the door while the
electromagnet is engaged.

against the door. The plate must be
able to pivot around the armature
screw.

4. Make sure the anti-spin guides are
in the two guidepin holes.

C. Screw the mounting plate to the door

frame or optional bracket:

1. Screw the two short self-tapping
screws in the slotted holes of the
mounting plate and adjust the
position of the mounting plate so
that it and the armature plate form
a 90-degree angle.

2. Once the position is correct, use the
long self-tapping screws to
permanently mount the bracket.

3. Remove the two short screws.

D. Drill the cable access hole.
E. Mount the electromagnet to the door

frame (fig. 1) — Use the Allen
wrench to screw the socket-head
mounting screws through the bottom
of the electromagnet into the
mounting bracket.

F. Connect the power leads (fig. 3):

1. Open the electromagnet.

2. Run two power leads from the power
supply through the cable access
hole into the electromagnet.

3. Connect the power leads to the
terminal block.

4. Close the electromagnet.

G. Test the unit.
H. Insert the tamper caps into the

mounting screw access holes. This
should be the last step, as once the
tamper caps are in place, they will be
difficult to remove.

SECO-LARM U.S.A., Inc.Page 2

FIG.

1

FIG.

2

FIG. 3: Status

Sensor Output ­Connect to an alarm
panel or other
monitoring device.

Adjustable Timer Delay — For
1~78 seconds, turn clockwise
to increase time. Timer starts
when power is applied.

E-941SA-1K2PD

Voltage Selection

12VDC

Magnet set for 12VDC
operation as supplied
from factory.

24VDC

Position a jumper over
the two middle pins for
24VDC operation.

Status Sensor Output — Monitors whether
the protected door is open or closed.

N.C. — Door opened, red LED on.

N.O. — Door closed, green LED on.

Relay — 3A @ 12VDC.

* Status LED — Indicates

whether the magnetic lock
is locked or unlocked.
Green — Locked
Red — Unlocked
Off — No power

Page 3