This manual contains a description of the
equipment supplied with the vehicle at the
time this manual was published. Some of the
units described herein will not be available
until a later date or are only available in certain markets.
Because this is a general manual for the Mii,
some of the equipment and functions that are
described in this manual are not included in
all types or variants of the model; they may
vary or be modified depending on the technical requirements and on the market; this is in
no way deceptive advertising.
The illustrations are intended as a general
guide and may vary from the equipment fitted
in your vehicle in some details.
The steering indications (left, right, forward,
reverse) appearing in this manual refer to the
normal driving movements of the vehicle except when otherwise indicated.
The equipment marked with an aster-
isk* is fitted as standard only in certain
versions, and is only supplied as optional extras for some versions, or are
only offered in certain countries.
® All registered marks are indicated with
®. Although the copyright symbol does
not appear, it is a copyrighted mark.
>> The section is continued on the follow-
ing page.
Important warnings on a given page
Detailed contents on a given page
General information on a given page
Emergency information on a given page
WARNING
Texts preceded by this symbol contain information on safety. They warn you about possible dangers of accident or injury.
CAUTION
Texts with this symbol draw your attention to
potential sources of damage to your vehicle.
For the sake of the environment
Texts preceded by this symbol contain relevant information concerning environmental
protection.
Note
Texts preceded by this symbol contain additional information.
This manual is divided into six large parts,
which are:
1. The essentials
2. Safety
3. Emergencies
4. Operation
5. Tips
6. Technical data
At the end of this manual, there is a detailed
alphabetical index that will help you quickly
find the information you require.
Foreword
struction Manual and its correspond-
This In
ing supplements should be read carefully to
familiarise yourself with your vehicle.
Besides the regular care and maintenance of
the vehicle, its correct handling will help preserve its value.
For safety reasons, always note the information concerning accessories, modifications
and part replacements.
If selling the vehicle, give all of the on-board
documentation to the new owner, as it
should be kept with the vehicle.
You can access the information in this manual using:
●
Thematic table of contents that follows the
manual’s general chapter structure.
●
Visual table of contents that uses graphics
to indicate the pages containing “essential”
information, which is detailed in the corresponding chapters.
●
Alphabetical index with many terms and
synonyms to help you find information.
WARNING
Read and always observe safety information concernin
bag ››› page 64, Important information
regarding the front passenger's airbag.
g the passenger's front air-
Thank you for trusting in us.
We wish you safe and enjoyable motoring.
SEAT, S.A.
Frequently Asked Ques-
s
tion
Before driving
How do you adjust the seat? ››› page 12
How do you adjust the steering wheel? ››› page 14
How do you adjust the exterior mirrors? ››› page 13
How do you turn on the exterior lights? ››› page 21
How does the automatic gearbox selector lever work?
››› page 27
How do you refuel? ››› page 31
How do you activate the windscreen wipers and windscreen washer system? ››› page 22
Emergency situations
A warning lamp lights up or flashes. What does this
mean? ››› page 25
Where are the first-aid kit and the warning triangle in
the vehicle? ››› page 70
How do you open the bonnet? ››› page 10
How do you perform a jump start? ››› page 43
Where is the vehicle tool kit located? ››› page 70
How do you repair a tyre with the anti-puncture kit?
››› page 35
How do you change a wheel? ››› page 36
How do you change a fuse? ››› page 34
How do you change a light? ››› page 79
How do you tow a vehicle? ››› page 42
Useful tips
How do you set the time? ››› page 89
When should the vehicle inspection should be performed? ››› page 90
How do you remove the luggage compartment cover?
››› page 125
How do you drive in an economical and environmentally-friendly way? ››› page 149
How do you check and top up the engine oil?
››› page 31
How do you check and top up the engine coolant?
››› page 32
How do you top up the windscreen washer fluid?
››› page 33
How do you check and top up the brake fluid?
››› page 33
How do you check and adjust tyre pressure values?
››› page 203
Vehicle washing tips ››› page 171
Functions of interest
How does the START-STOP system work? ››› page 160
What parking assistants are available? ››› page 153
How does tyre pressure monitoring work? ››› page 206
Locking and unlocking with the central locking switch
●
Locking: press the ››› Fig. 2 button. None
of the doors can be opened from the outside.
The doors can be opened from the inside by
pulling the inside door handle.
●
Unlocking: press the ››› Fig. 2 button.
››› in Introduction on page 94
››› page 94
››› page 9
Locking and unlocking the driver door
anua
ly
m
l
Fig. 3 Driver-side door handle with lock cylin-
.
der
As a general rule, when the driver door is
l other doors are locked. Unlocking
locked al
manually only opens the driver door.
●
Unfold the key shaft if necessary
›››
page 92.
●
Insert the key shaft into the lock cylinder to
unlock or lock the vehicle ››› Fig. 3.
Locking the passenger door manually
Fig. 4 To the front of the passenger side door:
Emergency
lock, hidden by a rubber cap.
The essentials
●
Unfold the key shaft if necessary
›››
page 92.
●
Insert the key shaft horizontally into the
opening and moved the coloured lever forward ››› Fig. 5.
●
Replace the rubber cap and close the door.
●
Check if the door is locked.
●
Have the vehicle checked by a specialised
workshop.
Note
The doors can be opened and unlocked individual
ly from the inside by pulling the door
handle. To open, pull the inner door release
lever twice ››› page 94.
Opening
●
Press the b
on on the
utt
vehicle key
››› Fig. 1 for about one second to unlock the
rear lid.
●
Insert the vehicle key into the lock cylinder
of the driver door and turn the key in an anti-
clockwise direction ››› page 94.
Closing
●
Grab the handgrip inside the rear lid
››› Fig. 6 (arrow).
●
Push the rear lid downwards until it locks
into place in the lock.
●
Ensure that it is correctly closed by pulling
on it firmly.
Fig. 5 Emergency locking of the vehicle using
le key
the vehic
The passenger door can be manually locked.
●
Open the door.
●
Remove the rubber cap to the front of the
door. The rubber c
symbol ››› Fig. 4.
ap is marked with a lock
Rear lid
Fig. 6 Rear lid open: hand grip
››› in Introduction on page 99
››› page 99
››› page 10
9
The essentials
Manual release mechanism for the
rear lid
Fig. 7 From the luggage compartment: Emer-
ency
nlocking of the booth hatch.
g
u
●
If necessary, fold the rear seat bench back-
t forward ››› page 12.
res
●
Remove equipment to access the inside of
the rear lid.
●
Unfold the key shaft ››› page 92.
●
Insert the key shaft into the rear lid opening ››› Fig. 7 and press the release lever in the
direction of the arrow to unlock the rear lid.
10
Bonnet
Fig. 8 A: Release lever in the footwell on the
driv
ide B: R
er s
elease lever on the bonnet
Fig. 9 C: Bonnet securing rod in the bonnet.
D: Bonnet sup
rod
ported by the bonnet securing
Opening the bonnet
●
Before opening the bonnet, make sure that
ind
creen wiper arms are in place
the w
s
against the windscreen
gine c
the en
omp
›››
in Working in
artment on page 188.
●
l the release lever
Pul
the arrow ›
from the lock carrier by a spring mechanism
›››
on page 188
●
the release lever
arr
●
clip in the direction of the arrow
plac
C
●
the en
●
opening catch
●
into its clip; Do not apply pressure!
If the bonnet is not correctly closed, open it
once again and close it correctly.
The bonnet is correctly closed when it is flush
with the corresponding parts on the bodywork.
›› Fig. 8 A. The bonnet is released
in Working in the engine compartment
.
Lift the bonnet up slightly while pressing
w to completely open the bonnet.
o
Take out the bonnet support rod from its
e it in the corresponding open position
4
ow).
D (arr
sing the bonnet
lo
Slightly lift the bonnet ›››
gine c
omp
Take out the bonnet support rod from the
3
C in the openin
Let the bonnet fall from a height of 30 cm
››› in Working in the engine compart-
ment on page 187
››› page 187
1
in the direction of
2
B in the dir
artment on page 188.
4
D and in
g c
in Working in
sert it into its clip
ch.
at
ection of the
3
C and
The essentials
Controls for the windows*
Fig. 10 In the driver door: buttons for front
indo
s.
w
w
●
Opening the window: Press the b
●
losing the window: Pull the button.
C
1
Window on the front left door
2
Window on the front right door
››› in Opening and closing the windows
electrically on page 101
utt
Panoramic sunroof*
Fig. 11 In the interior roof: turn the knob to
open and close
on.
Fig. 12 In the interior roof: press or pull the
b t
aise the sunroof and close it.
kno
o r
To raise the sliding/tilting sunroof, the knob
be in the basic position
must
●
Opening: Turn the switch to position
3
Fig. 11
›››
.
1
.
»
11
●
enience position: Turn the switch to
Conv
position ››› Fig. 11
●
Closing: Turn the switch to position
Fig. 11
›››
●
To tilt open: Push the switch to position
Fig. 12
›››
wn the switch until you reach the de-
hold do
sired position.
●
Lowering: Pull the switch to position
››› Fig. 12
wn the switch until you reach the de-
hold do
sired position.
2
.
1
.
4
. For an intermediate position,
5
. For an intermediate position,
The essentials
Before driving
anua
ly adjusting the seats
M
l
To raise it, move the seat back until the
h engages. Pull the lever and tilt
catc
open the backrest. The backrest must engage in the upright position.
››› in Manual front seat adjustment on
page 112
››› in Opening and closing the panor-
12
amic sunroof on page 102
››› page 102
Fig. 13 Front left seat controls
The front seat head restraints are integrated
in the back
possible.
rests and adjusting them is not
1
Forward/back: pull the lever and move
the seat forwards. The front seat must be
engaged when the lever is released!
2
Raising/lowering: pull the lever up or
push down (several times if necessary)
from its home position.
3
Tilting the backrest: pull the lever and
adjust the backrest seat angle until you
reach the desired position. The seat backrest must be engaged.
3
Folding/Raising (Easy Entry only in 3-
door vehicles): to fold, pull the lever and
at the same time move the seat forward.
The essentials
Seat belt adjustment
Fig. 14 Positioning and removing the seat
kle.
belt buc
Fig. 15 Correct seat belt and head restraint
position
s, viewed from front and the side.
To adjust the seat belt around your should-
s, a
st the height of the seats.
er
dju
The shoulder part of the seat belt should be
well centred over it, never over the neck. The
seat belt lies flat and fits comfortably on the
upper part of the body.
The lap part of the seat belt lies across the
pelvis, never across the stomach. The seat
belt lies flat and fits comfortably on the pelvis.
››› in Introduction on page 52
››› page 56
Seat belt tensioners
During a head-on, lateral or rear collision, the
seat belts
on the front seats tighten automat-
ically.
The tensioner can be triggered only once.
››› in Service and disposal of belt ten-
sion devices on page 58
››› page 57
Adjusting the exterior mirrors
Fig. 16 In the driver door: rotary control for
the exterior el
Adjusting the exterior mirrors: Turn the knob
o the c
t
L/R
ectric mirrors
esponding position:
orr
Turning the knob to the desired position, adjust the mirrors on the driver
»
13
The essentials
side (L, left) and the passenger side (R,
o the dir
right) t
Depending on the equipment fitted on
the vehicle, the mirrors may be heated
according to the outside temperature.
ection de
››› in Exterior mirrors on page 111
››› page 111
Adjusting the steering wheel
Fig. 17 Mechanical steering wheel adjust-
ment
●
Push the lever ›
●
Adjust the steering wheel so that you can
ho
ld ont
on the outside of the ring at the 9 o'clock and
14
›
o the steering wheel with both hands
Fig. 17
›
1
sired.
downwards.
3 o'clock positions and your arms slightly
bent.
●
sh the lever firmly upwards until it is
Pu
flush to the steering column ›››
g the s
eering wheel position on
in
t
page 49.
››› in Adjusting the steering wheel po-
sition on page 49
››› page 49
in Adjust-
Airbags
ont
ont
airb
airb
ags
ag for the driver.
Fr
Fig. 18 Location and deployment area of the
fr
The essentials
Fig. 19 Location and deployment area of the
ont
ag for the passenger.
fr
airb
In conjunction with the seat belts, the front
ag sy
airb
passenger additional protection for the head
and chest in the event of a severe frontal collision. Always remain as far away as possible
from the front airbag ››› page 48. This
way, in the event of an accident, the front air-
tem gives the driver and the front
s
bags can deploy fully when triggered, providing maximum protection.
The front airbag for the driver is located in
the steering wheel ››› Fig. 18 and the airbag
for the front passenger is located in the dash
panel ››› Fig. 19. Airbags are identified by the
word “AIRBAG”.
When the front airbags are triggered they fill
the zones marked in red ››› Fig. 18 and
››› Fig. 19 (radius of action). Therefore, ob-
jects should never be placed or mounted in
these areas ›››
page 61
side the range of the front airbag for the driver and the front passenger, e.g. the baseplate for the mobile phone support.
The airbag covers fold out of the steering
wheel ››› Fig. 18 and the dash panel
in Front airbags on
, Factory-fitted accessories are out-
››› Fig. 19 when the driver and front passen-
ger airbags, respectively, are triggered.
››› in Front airbags on page 61
Disabling the front passenger front
ag
airb
Fig. 20 On front passenger side: Key switch
or en
ling and disabling the front passen-
f
ab
ger front airbag.
The front passenger front airbag must be disabled when a r
ted.
Disabling the front passenger front airbag
●
Switch the ignition off.
●
Open the door on the front passenger side.
●
Unfold the vehicle key blade
›››
●
Using the vehicle key, turn the key switch to
OFF››› Fig. 20.
●
Close the door on the front passenger side.
●
The control lamp on
the dash panel will remain lit while the ignition is switched on ››› page 62.
ear-facing child seat is moun-
page 92.
»
15
The essentials
››› in Manual disabling and enabling of
the front passenger front airbag with the
key switch on page 63
››› page 62
Side airbags
Fig. 21 On the side of the front seat: location
the s
of
16
ide airb
ag
Fig. 22 On the left side of the vehicle: deploy-
ment are
a of side airbag
The side airbags are located in the outer
cushion of
seat backrests ››› Fig. 21. Their position is in-
dicated by the word “AIRBAG”. The area
marked in red ››› Fig. 22 indicates the side
airbag deployment zone.
In the event of a side-on collision, the side
airbag will deploy in the side of the vehicle
affected ››› Fig. 22, thus reducing the risk of
injuries to passengers on the side of the
body and the head facing the accident side.
the driver and front passenger
››› in Side airbags* on page 62
Child seats
Important
front passenger's airbag
Fig. 23 Passenger's side sun visor: airbag
tic
s
Fig. 24 On the rear frame of the passenger
ide door: airb
s
information regarding the
er.
k
ticker.
ag s
The essentials
A sticker with important information about
senger airbag is located on the pas-
the pas
Mounting systems
Always secure child seats properly and safely
in the vehic
manufacturer's installation instructions.
Mounted child seats must rest correctly on
the vehicle's seat and must not move or rock
more than 2.5 cm.
Child seats equipped for a Top Tether strap
must also be secured using the Top Tether re-
le according to the child seat
senger's sun visor and/or on the passenger
side door frame.
››› in Important information regarding
taining strap in the vehicle ››› page 20. At-
tach the retaining strap to the corresponding
retaining rings only. Not all rings can be used
with the Top Tether system. Always tighten
the Top Tether retaining strap so that the
child seat fits snugly against the corresponding seat in the vehicle.
the front passenger's airbag on page 65
››› page 64
Fig. 25 On the rear seats: Possible installations
for the chi
ld seat.
Specific mounting systems for each country
Attachment variants ››› Fig. 25:
A
Europe: ISOFIX retaining rings and upper
retaining strap ››› page 18 and
››› page 20.
B
Three-point seat belt and upper retaining
strap ››› page 18.
»
17
The essentials
The systems include the child restraint sys-
em mou
t
g with an upper retaining strap
ntin
(Top Tether) and lower anchoring points on
the seat.
Securing child seats with the seat belt
The seat belt may be used to secure child
seats w
ith the universal marking (on the or-
ange label) to the vehicle seats marked with
a u in the table below.
Category
Group 0
Up to 10 kg
Category 0+
Up to 13 kg
Group 1
9 to 18 kg
Group 2
15 to 25 kg
Group 3
22 to 36 kg
a)
Compliance with current national legislation and the manufacturer's instructions is required when using or installing child
seats.
18
Front passen-
a)
ger
uu
uu
uu
uu
uu
Rear seats
Securing the child seat using the seat belt
●
Please read and observe the child seat
manufacturer's handling instructions.
●
Move the front passenger seat, or the rear
seat bench back as far as possible and, in
the case of an adjustable backrest, set it in
the upright position ››› page 48.
●
Positioning the child seat on the seat according to the manufacturer's instructions.
●
Fasten the seat belt or pass it around the
child seat structure in the manner described
in the manufacturer's instructions.
●
Make sure the seat belt is not twisted.
●
Insert the latch plate into the buckle for the
appropriate seat and push it down until it is
securely locked with an audible click.
●
Ensure that the upper belt web lies tightly
on the child seat.
●
Pull the belt (it must be no longer possible
to pull the lower belt webbing out).
Removing the child seat
The seat belt must not be unfastened until
the vehicle has come to a standstill.
●
Press the red button on the buckle. The
latch plate is released from the buckle.
●
Guide the belt back by hand so that it rolls
up easily and the trim will not be damaged.
●
Remove the child seat from the vehicle.
››› in Safety instructions on page 66
Fixing the child seat with the ISOFIX
system
Fig. 26 On the vehicle seat: identification var-
ants
the anchor points for the child seats
i
of
Each seat of the rear seat bench has two r
tainers named lower anchor points.
Summary chart for assembly with the ISOFIX
system
The following table shows the assembly possibilities for ISOFIX or i-Size child seats on
the ISOFIX anchorage points of the different
vehicle seats.
e-
Age group
Group 0: up
to 10 kg
Group 0+:
up to 13 kg
Group 1:
from 9 to
18 kg
Group 2:
from 15 to
25 kg
Group 3:
from 22 to
36 kg
i-Size child
restraint
system
Class ac-
Front pascording
to size
senger
a)
seat
EXIL-SU
EX
DX
CX
DX
CX
BX
B1X
AX
–XIL-SU
–XIL-SU
–XX
Rear
seats
IL-SU
IL-SU
IUF
The essentials
Age group
Class ac-
to size
X: seat not suitable for securing an ISOFIX or i-Size child
seat from this group.
IL-SU: seat suitable for installing an ISOFIX child seat
with semi-universal approval. Take the child seat manufacturer's vehicle list into account.
IUF: seat suitable for fixing an ISOFIX child seat with universal approval.
a)
The indication of class according to size corresponds to the
authorised bodyweight for the child seat. In child seats with universal or semi-universal approval, the class according to size is
indicated on the ECE approval label. The indication of class according to size is stated on the corresponding child seat.
Child seats with rigid mounting
For the installation of a child seat with rigid
mounting auxiliary introduction elements can
be used. These elements facilitate fitting and
protect the upholstery. They form part of the
supply volume of the child seat or can be acquired at a SEAT dealership. If necessary,
these elements are inserted in both anchor
points of the vehicle
s on p
tion
●
Observe the manufacturer's instructions
e 66.
ag
when installing and removing the child seat
›››
in Safety instructions on page 65.
●
Press the child seat onto the retaining rings
›››
Fig. 26 in the direction of the arrow. The
child seat must be safely engaged and click
audibly into place.
cording
Front pas-
senger
a)
seat
›››
in Safety instruc-
Rear
seats
●
Pull on both sides of the child seat to en-
sure that it is secure.
Child seat with adjustable retaining straps
●
Observe the manufacturer's instructions
when installing and removing the child seat
›››
in Safety instructions on page 65.
●
Place the child seat on the seat cushion
and attach the r
etaining strap hooks to the
retaining rings ››› Fig. 26.
●
Tighten the straps evenly using the corresponding adjustment device. The child seat
must sit flush against the vehicle seat.
●
Pull on both sides of the child seat to ensure that it is secure.
››› in Safety instructions on page 65
19
Securing a child seat with the Top
ether r
T
Fig. 27 Example of an upper retaining strap
c
●
Observe the manufacturer's instructions
when inst
›››
●
Unlock the seat backrest and fold it gently
forw
●
Remove the head restraints situated be-
hind the child seat and store them safely in
the vehicle ››› page 48.
●
Guide the upper retaining strap from of the
child seat back to the luggage compartment,
feeding it through the seat backrest and the
rear shelf.
●
Fold back the seat backrest and push it
firmly into the lock.
●
Secure the child seat to the lower anchor
points ››› page 18
20
aining strap
et
onnect
ed.
alling and removing the child seat
in Safety instructions on page 65.
ard ››› page 12.
The essentials
●
Hook the upper retaining strap in the lug-
gage compartment, to the corresponding retaining ring ››› Fig. 27.
●
Tighten the strap so that the top of the
child seat rests on the seat backrest.
››› in Safety instructions on page 65
Starting the vehicle
Ignition lock
Fig. 28 Ignition key positions.
Switch ignition on: Place the key in the ignition and star
Locking and unlocking the steering wheel
●
Engaging the steering wheel lock: Remove
the key from the ignition and turn the wheel
t the engine.
until it locks. In vehicles with an automatic
gearbox, the gear lever must be in the N position in order to remove the key. If necessary,
press the locking key on the selector lever
and release it again.
●
Unlocking the steering wheel: Put the key
into the ignition and turn it at the same time
as the steering wheel in the direction indicated by the arrow. If it is not possible to turn
the steering wheel, it may be because it is
locked.
Turning on/switching off the ignition, glow
plugs reheating
●
Switch ignition on: Turn the key to the
position.
●
Switch ignition off. Turn the key to the
position.
●
Diesel vehicles :
when the ignition is switched on.
Starting the engine
●
Manual gearbox: press the clutch pedal all
the way down and move the gearbox lever into neutral.
●
Automatic gearbox: press the brake pedal
and move the selector lever to N.
●
Turn the key to the
ally returns to the
tomatic
s the accelerator.
pres
The glo
w p
3
position. The key au-
2
position. Do not
2
1
lugs reheat
The essentials
Start-Stop System*
When you s
the Start-Stop system* turns off the engine.
The ignition remains switched on.
top and release the clutch pedal,
››› in Switching on the ignition and
starting the engine on page 133
››› page 133
Lights and visibility
sw
Light
Fig. 29 Dash panel: light control.
Turn the switch to the required position
Fig. 29.
›››
ch
it
Sym-
Ignition switched
bol
off
Fog lights, dipped
beam and side lights
off.
The “Coming home”
and “Leaving home”
guide lights may be
switched on.
Side light on.
Dipped beam head-
light off
Front fog lights: mo
first position, from positions , or .
Rear fog light: move the switch completely
from positions , or .
Switching off fog lights: Push the switch or
turn it to the position.
››› in Switching lights on and off on
page 104
››› page 103
Ignition is
switched on
Light off or daytime
driving light on.
Automatic control of
dipped beam and
daytime running
light.
Dipped beam
switched on.
ve the switch to the
Turn signal and main beam lever
Fig. 30 Turn signal and main beam lever in
their initial po
More the lever to the required position:
1
Right turn s
light (ignition switched off).
2
Left turn signal: Left-hand parking light
(ignition switched off).
3
Main beam switched on: Control lamp
lit up on the instrument panel.
4
Headlight flasher: lit up when the lever is
pushed. Control lamp lit up.
Lever all the way down to switch it off.
sition
ignal: Right-hand parking
››› in Turn signal and main beam lever
on page 105
››› page 105
21
The essentials
Hazard warning lights
Fig. 31 Dash panel: switch for hazard warn-
g lights.
in
Switched on, for example:
●
When approaching a traffic jam
●
In an emergency
●
The vehicle has broken down
●
When towing or being towed
››› in Hazard warning lights on
22
page 106
››› page 106
Interior lights
Side lights: Function
Switching off the reading light.
Switching on the reading light.
Switches door contact control on (central position).
The reading light comes on automatically
when the vehicle is unlocked, a door is
opened or the key is removed from the igni-
tion.
The light goes off a few seconds after all the
doors are closed, the vehicle is locked or the
ignition is switched on.
Note
The reading lights go out when the vehicle is
locked, or a f
moved from the ignition. This prevents the
vehicle's battery from discharging.
ew minutes after the key is re-
Windscreen wipers and window wiper
de
bla
Fig. 32 Operating the windscreen wiper and
iper.
rear w
More the lever to the required position:
0
1
2
3
4
5
6
Windscreen wiper off.
Windscreen interval wipe.
Slow wipe.
Continuous wipe.
Brief wipe - short wipe. Hold the lever
down for more time to increase the wipe
frequency.
Automatic wipe for cleaning wind-
screens with the lever up.
Interval wipe for rear window. The wiper
will wipe the window approximately ev-
ery six seconds.
The essentials
More the lever to the required position:
7
Automatic wipe for cleaning rear win-
dows with the lever pressed.
››› page 108
››› page 45
SEAT information system
oduction
Intr
With the ignition switched on it is possible to
ss different messages via the display on
acce
the instrument panel display.
The number of messages displayed on the instrument panel display will vary according to
the vehicle electronics and equipment.
A specialised workshop will be able to programme or modify additional functions, according to the vehicle equipment. SEAT recommends taking your car in for technical
service.
WARNING
Any distraction may lead to an accident, with
the risk of
injury.
●
Do not con
ment panel screen when driving.
sult the messages on the instru-
Management of indications on the
lay
disp
Fig. 33 Windscreen wiper lever: control but-
tons.
Calling up options
●
Switch the ignition on.
●
If a message or vehicle symbol is dis-
yed, press
pla
●
Press the top or bottom part of the rocker
switc
appear
h ››› Fig. 33
s.
OK/RESET
›
(›
› Fig. 33
B
until the desired option
A
Multifunction display (MFI)
The multifunction display (MFD) has two automatic
memories: 1 - Partial memory and 2 -
Total memory. The selected memory will be
shown in the lower right-hand corner of the
display.
With the ignition switched on, and memory 1 or
2 displayed, briefly press
one memory to another.
The memory stores the values for the
journey and the consumption from the
moment the ignition is switched on until
Trip memory
(for a single
journey).
Total memo-
).
ry (for all
journeys).
it is switched off again.
If the journey is broken for more than 2
hours, the memory is automatically
erased. If the journey is continued in
less than 2 hours after the ignition is
switched off, the new data is added to
the data already stored in the memory.
The memory stores the values of any
number of journeys, until it counts a to-
tal of 19 hours and 59 minutes of driving, or 1999.9 km or miles of driving,
depending on the type of instrument
panel fitted. On reaching either of these
limits, the memory is automatically
erased and starts to count from 0 again.
Possible displays
MenuFunction
Time
OK
to change from
Current time in hours (h) and minutes (min).
»
23
MenuFunction
Travelling
time
Current
fuel consumption
Average
fuel consumption
Operating
range
Distance
covered
Average
speed
Digital
display of
speed
24
This indicates the hours (h) and minutes (min) since the ignition was
switched on.
The current fuel consumption display
operates throughout the journey, in
l/100 km; with the engine running
and the vehicle stopped, in l/hour.
After turning on the ignition, average
fuel consumption in litres/100 km
will be displayed after travelling
about 100 metres. Otherwise horizontal lines are displayed. The value
shown is updated approximately every 5 seconds.
Approximate distance in km that can
still be travelled with the fuel remaining in the tank, assuming the same
style of driving is maintained. This is
calculated using the current fuel consumption.
Distance travelled, after ignition is
switched on, in km.
The average speed will be shown after a distance of about 100 metres
has been travelled. Otherwise horizontal lines are displayed. The value
shown is updated approximately every 5 seconds.
Current speed displayed digitally.
The essentials
MenuFunction
Digital
coolant
temperature
gauge
Warning at
--- km/h
Changing between display modes
●
Press the rocker switch in the windscreen
w
iper l
Storing a speed for the speed warning
●
Select the display Speed warning at
--- km/h.
●
Press
e the current speed and switch off the
stor
warning.
●
In addition, set the required speed by
pressing the rocker switch on the windscreen
wiper lever or
function s
press
peed i
s
●
To switch off, press
deleted.
anually erasing memory 1 or 2
M
●
Select the memory to be erased.
Digital display of the current temperature of the engine liquid coolant.
If the stored speed is exceeded (between 30 - 250 km/h, or 18 155 mph), an audible warning is given together with a visual warning.
ev
er.
OK
on the windscreen wiper lever to
or buttons on the multi-
teering wheel for 5 seconds. Next,
OK
again or wait a few seconds. The
stored and the warning activated.
s
OK
. The stored speed is
●
Press and hold the eject button
imately 2 seconds.
prox
OK
for ap-
Cruise control
Operating the cruise control system
(CCS)*
Fig. 34 Switch and controls for operating the
CCS.
●
Switching on the CCS: Move switch
1
Fig. 34
›››
s
as been programmed, the system will
peed h
not control it.
●
Activating the CCS: Press button ››› Fig. 34
2
in the area.
memorised and controlled.
●
Temporarily switching off the CCS: Move
switch ››› Fig. 34
brake. The cruise control system is switched
off temporarily.
The system is on. If no
to .
The current speed is
1
or p
to
sh the
u
●
ating the CCS: Press button
Reactiv
2
››› Fig. 34
i
saved and controlled again.
s
●
Increasing stored speed during CCS regulation: press button
c
erates until the new stored speed.
el
●
Reducing stored speed during CCS regulation: press button
s
peed b
until reaching the new stored speed.
●
Switching off the CCS: Move switch
››› Fig. 34
t
ed and the memori
. The memorised speed
in
2
. The vehicle ac-
in
y 1 km/h (1 mph). Speed is reduced
2
1
The system is disconnec-
to .
sed speed is deleted.
››› in Cruise control operation on
page 156
in t
o lower the
››› page 155
Warning lamps
On the instrument
The control and warning lamps are indicators
gs, ›››
of warnin
s.
tion
Some c
on when the ignition is switched on, and
switch off when the engine starts running, or
while driving.
When certain control and warning lamps are
lit, an audible warning is also heard.
panel
›
, faults ›
ontrol and warning lamps come
› or certain func-
The essentials
Handbrake applied.
Do not continue driving!
The brake fluid level is too low or
there is a fault in the brake system.
it lights up: Do not continue
driving!
The liquid coolant level is too low,
the engine liquid coolant temperature is too high or
there is a fault in the liquid coolant
system.
flashes: engine coolant system
faulty.
Do not continue driving!
Engine oil pressure too low.
lights up or flashes: Do not continue driving!
Fault in the steering.
On the instrument panel: driver or
passenger has not fastened seat
belt.
Faulty generator.
Vehicles with the Start-Stop system: it is necessary to start the engine manually.
››› page
135
››› page
192
››› page
192
››› page
189
››› page
147
››› page
52
››› page
196
››› page
160
it lights up: ESC* faulty or switched
off by the system. ALTERNATIVELY:
flashes: ESC* or ASR regulating.
it lights up: Traction Control* faulty
or switched off by the system. ALTERNATIVELY:
flashes: Traction Control* regulator
operating.
ABS faulty or does not work.
Rear fog light switched on.
lights up or flashes: fault in the
emission control system.
Fault in engine management.
lights up or flashes: fault in the
steering system.
Fuel tank almost empty.
The natural gas tank is almost
empty.
Fault in airbag system and seat
belt tensioners.
Tyre pressure* too low
Left or right turn signal.
Hazard warning lights on.
››› page
135
››› page
103
››› page
151
››› page
147
››› page
183
››› page
183
››› page
58
››› page
206
››› page
103
››› page
70
»
25
The essentials
Cruise control operating.
Main beam on or flasher on.
The natural gas engine coolant
temperature is too low.
Control lamps on the instrument panel
A passenger in the rear seats
has fastened their seatbelt.
A passenger in the rear seats
has not fastened their seat belt.
flashes quickly: the City Safety
Assist system function* brakes
automatically or has braked automatically. Or:
flashes slowly: City Safety Assist
function is not currently available.
The City Safety Assist* function
has been connected manually. It
switches off after 5 seconds.
flashes: The City Safety Assist*
26
function has been manually disconnected.
after the ignition is switched on:
indication that the end of the
period for an inspection to be
performed is approaching.
››› page
155
››› page
103
››› page
192
››› page
52
››› page
52
››› page
156
››› page
156
››› page
156
››› page
90
it lights up: the Start-Stop system is enabled. ALTERNATIVELY:
flashes: the Start-Stop system is
not available.
The Start-Stop system is enabled but the engine cannot be
automatically stopped.
flashes in addition to the rest of
the segments of the fuel gauge:
Fuel tank almost empty.
WARNING
If the warning lamps are ignored, the vehicle
may
stall in traffic, or may cause accidents
and severe injuries.
●
Never ignore the warning lamps.
●
Stop the vehicle safely as soon as possible.
●
Park the vehicle away from traffic and ensure that there are no highly flammable materials under the vehicle that could come into
contact with the exhaust system (e.g. dry
grass, fuel).
●
A faulty vehicle represents a risk of accident for the driver and for other road users. If
necessary, switch on the hazard warning
lamps and put out the warning triangle to advise other drivers.
●
Before opening the bonnet, switch off the
engine and allow it to cool.
●
In any vehicle, the engine compartment is a
hazardous area and could cause severe injuries ››› page 187.
››› page
160
››› page
183
CAUTION
Failure to heed the warning lamps when they
appear m
ay result in faults in the vehicle.
Gearbox lever
Manual
gearbox
Fig. 35 Gear shift pattern of a 5-speed man-
arbox
ual ge
The position of each of the gears is shown on
tick ››› Fig. 35.
the gear s
●
Keep the clutch pedal pushed all the way
down.
●
Move the gearbox lever to the required po-
sition ›››
page 143
●
in Manual gear change on
.
Release the clutch pedal to engage clutch.
The essentials
Selecting reverse gear
●
Engage reverse gear only when the vehicle
topped.
is s
●
Keep the clutch pedal pushed all the way
down ›››
page 143
●
push the lever downwards.
●
then backward as shown on the lever.
●
in Manual gear change on
.
Place the gearbox lever into neutral and
Slide the gearbox lever to the right, and
Release the clutch pedal to engage clutch.
››› in Manual gear change on page 143
››› page 143
Automatic gearbox
Fig. 36 Automatic gearbox diagram of gears
R
Reverse gear
N
Neutral (idlin
Drive (forward)
D
g)
Tiptronic mode: pull the lever forwards
M
(+) to go up a gear or backwards (–) to
go down a gear.
››› in Automatic gear change on
page 144
››› page 144
27
Air conditioning
w doe
Ho
the Climatronic* work?
s
The essentials
Fig. 37 At the top of the centre console: Clima-
tronic c
ontrols
Switching off
Temperature
Air distribution
28
Switch the system off by pressing several times on the lower button ››› Fig. 37
Cooling mode
button switches cooling mode on and off.
The
Automatic mode
button switches the automatic mode on and off. The automatic mode maintains temperature constant in the vehicle’s interior. Temperature
The
and the amount and distribution of air are controlled automatically. Modifying ventilation automatically switches off the automatic mode.
Press buttons 1 and 2 ››› Fig. 37 to adjust the temperature. The adjusted temperature is displayed on the screen.
Fan
The
››› Fig. 37 buttons are used to adjust fan speed.
: The air is distributed towards the upper part of the body through the dash panel air vents
: Air distribution to footwells
: Air distribution to the windscreen
Loading...
+ 202 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.