Sears Kenmore Air Conditioner Owner's Manual

Record Your Model and Serial Numbers .............. Cover

Important Safety Instructions ....................................... 2

Energy Saving Ideas ...................................................... 2

How and Why ................................................................ 3

Normal Sounds .............................................................. 3

Front Installation ........................................................ 4-5

Using the Air Conditioner ............................................. 6

Air Conditioner Features ............................................ 6-7

Care and Cleaning ...................................................... 7-8

Routine Maintenance .................................................... 9

Troubleshooting Guide ................................................ 10

Sears Service ................................................................ 11

Warranty ...................................................................... 11

Read and Save These Instructions

This Owner's Guide provides specific operating instructions for your model Usethe air conditioner only as instructed in this

guide. These instructions are not meant to cover every possible condition and situation that may occur Common

senseand caution must be practiced when installing, operating, and maintaining any appliance

Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers The serial plate islocated behind the left front louvers
Readingthe numbers may be easierby using a flashlight or by removing the cabinet front asinstructed under "Care and

Cleaning " On some models, the serial plate is located on the outside of the cabinet

Model Number:
Serial Number:
Purchase Date:

Sears, Roebuck and Co., Hoffman Estates, UL60179 U.S.A.

P!N3090008 t7 (9903)

Important Safety
Unstructions

i

Avoid fire hazard or

electricshock Do not use an extensioncord
3r an adaptor plug Do not remove any

0tong from the power cord

Grounding type
wall receptacl

Do not under "_
any circumstances /

cut, remove, /
or bypass /
the grounding prong I

fromth!sp!,g- J

Power supply
cord with 3-prong
grounding plug

Read all instructions before using this air conditioner.

[!_ For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance Read product labels for flammability and

other warnings

Prevent Accidents

To reduce the risk of fire, electrical shock, or injury to persons when using your

air conditioner, follow basic precautions, including the following:

• Be sure the electrical service is adequate for the model you have chosen
o If the air conditioner is to be installed in a window, you will probably want

to clean both sides of the glass first If the window is a triple-track type with
a screen panel included, you may want to remove the screen completely

before instatJation

o Be sure the air conditioner has been securely and correctly installed

according to the separate installation instructions provided with this manual
Save this manual and installation instructions for possible future use in
removing or reinstalling this unit

• When handling the air conditioner, be careful to avoid cuts from sharp
metal fins on front and rear coils

Electrical Information

The complete electrical rating of your new room air conditioner is stated on
the serial plate Refer to the rating when checking the electrical requirements

= Be sure the air conditioner isproperly grounded To minimize shock and fire

hazards, proper grounding is important The power cord isequipped with a
three-prong grounding plug for protection against shock hazards
Your air conditioner must be used in a properly grounded wall receptacle If

the wall receptacle you intend to use is not adequately grounded or

protected by a time delay fuse or circuit breaker, have a qualified electrician
install the proper receptacle

o Do not run air conditioner with outside protective cover in place This could

result in mechanical damage within the air conditioner,

o Do not use an extension cord or an adapter plug,

Energy Saving Ideas

o The capacity of the room air conditioner must fit the room size for efficient
and satisfactory operation
o Install the room air conditioner on the shady side of your home A window

that faces north is best because it is shaded most of the day,

o Do not block air flow inside with blinds, curtains or furniture; or outside with

shrubs, enclosures, or other buildings

o Close the fireplace damper, floor and wall registers so cool air does not

escape up the chimney and into the duct work

Keep blinds and drapes in other windows closed during the sunniest part of the

day,
° Clean the air filter as recommended in the section "Care and Cleaning"
o Proper insulation and weather stripping in your home will help keep warm

air out and cool air in

• External house shading with trees, plants or awnings will help reduce the air

conditioner's work load

• Operate heat producing appliances such as ranges, washers, dryers and

dishwashers during the coolest part of the day

How and Why

Your room air conditioner provides the following functions to make hot
weather living more comfortable:

o Cools and circulates room air
° Lowers humidity by removing excess moisture

• Filters out summertime dust, dirt, and some airborne impurities

The air conditioner performs these functions by drawing room air through a
filter which traps dust and dirt particles The air then passes over a cooling coil
which refrigerates the air and removes excess moisture The same air isthen

returned to the room-- cooler, drier and cleaner Moisture removed from the
room air is carried to the outside and evaporated

Your air conditioner is designed to be easy to operate and to provide plenty
of cooling power

NormaR Sounds

Compressor
The _igh efficiency

compressor may have a

high pitched hum or pulsating
noise that cycles on and off

Unit Vibration
The unit may vibrate and
make noise because of poor
wail or window construction

Fan

You may hear air

from the fan

Thermostat

As the cooling system

the thermostat may click

/

Condenser

may hear droplets of
water hitting the condenser
causing a "pinging or
clicking" sound

3

Front Installation

:_:!}:':? L Seal t

Instattina Bottom RailSeal

Vertical Louver _

Screw

l

Unit Cover

%_-_ Screw

Horizontal
Louvers Front Panel

Front Installation-SideAir Discharge

FIG t

Front Installation - SideAir Discharge

F!,G,2

Installing Bottom Rail Seal (some models)

Some models areshipped in a removable sleevethat must be positioned properly for
safe and efficient sealing Follow the InstallationInstructions supplied To install the

Bottom RailSeal,position the seaIon top of the bottom rail,flush with the front edge

of the rail and in contact with the side seals

Manual Vertical Louver Adjustment (side air discharge)

Comptete this adjustment before installing front panel

1 Adjust the vertical louvers to the straight position by using the handle

2. The dial plate and knobs are packed separately To install them, refer to
Installing the Dial Plate and Front Frame section on the next page

Front Installation - Some Side Air Discharge Models (FIG. 1)

Install the front panel with filter as follows:

1 Adjust the horizontal louvers to the straight position Hold the front straight

until the vertical louver handle lines up between the bottom horizontal louver

and the discharge opening

2 Pressthe front straight onto the cabinet until the holes in the flange of the

plastic front tineup with the screw holes in the metal cabinet Fasten the front
panel in Place with the two screws provided

Front installation - Some Side Air Discharge Models (FIG. 2)

t Positionthe top of the decorative front cover onto the top flange of metal case

and then align the tabs on the front with slots in metal case

2 Carefully pull down on the front cover to engage top tabs while pushing the

front cover over the metal case To ensure proper alignment the side

locking tabs will "click" when the front cover is properly installed
Note: Power cord must be held in position inside metal case half-round relief

while sliding front cover over metal case.

3 Install the front cover retaining screw at the bottom of the unit

Installing the Vent Control (onsome models)

The vent control handle is included in the decorative front kit (Fig 3) The handle

must be installed before the decorative front is attached See illustration below

t Insert the handle with the "Etchings (Vent/Air)" facing to the left

2 Slip the black door extension into the split at the end of the handle

3. For easeof assembly,Pusgthe handle in while pressingthe door extension
against the foam until the two pieces lock together

4 Move handle in and out to be sure vent isoperating properly

FIG 3

4

Front installation

(continued)

Installing Dial Plate and Front Frame

Some models require installation of the dia! plate and the front panel of the air
conditioner included in a decorative kit, To assemble, follow these steps

STEP 1: INSTALL DIAL PLATE AND BUTTONS OR KNOBS:

• Remove control knobs from front kit
(some models),

° Carefully remove protective film

from the front of the dial plate
(some models),

o Line up holes on dial plate with the

correct control stems and push dial
plate to control panel surface

° While holding dial plate in place

install control knobs on protruding

stems,

Some Models

STEP 2: INSTALL FRONT FRAME TO UNIT.

Side Air Discharge

Decorative Front

° Position the top of the decorative front over the top flange of the case, and align the tabs with the

slots in the case

oAs you install the front frame to the unit be surethe vent handle is positioned through the front in the proper

location,

• Carefully pull down on the front to engage the top tabs, while pushing the front over the case to
ensure proper alignment

° The side tabs wilt "click" when front is seated,

• Install front retaining screw(s) at the bottom of the front (Fig 1), or behind the filter handle (Fig 2)

FIG !

FIG 2

Using the Air ¢:ondit oner

NOTE: Ifthe air conditioner is turned off,

wait 3 minutes before restarting This

allows pressure inside the compressor to
equalize Failure to follow these
instructions may cause inefficient
operation.

I_ To reduce the risk of fire, electric shock, or injury to persons, read the
IMPORTANT SAFETYINSTRUCTIONSbefore operating this appliance.

To begin operating the air conditioner, follow these steps:

1 Plug in the air conditioner (To prevent electrica! hazards, do not use an

extension cord or an adapter plug )
2 Set the exhaust vent to the CLOSEDposition
3 Set the TEMP Controi to the coolest setting
4 Set the fan control at the highest level

5. Adjust the louvers for comfortable air flow

6 Once the room has cooled, select the POWER SAVERMODE and/or adjust the

TEMP Control to the setting you find most comfortable

Air Conditioner Features

VENT

OPEN CLOSE

MODE

OFF

HIGH FAN

COOL ONLY

MED POWER

COOL SAVER

LOW

COOL

TEMP

e 5 e

\\_ COOLER

(some models)

:ii:!/::':WI::::!::I¸::: ::i:::

FAN COOL

OFF

HEATControl (some models)

Review the "Air Conditioner Features" section for other settings

The controls featured in this manual are representational of the many models

available. Your model may took slightly different,,

TEMP Control
The TEMPControl serves as the thermostat to set the degree of room

coolness Turn the knob clockwise from t to 9 to increase the cooling
temperature

COOL MODES

When in one of the COOL settings, the air conditioner runs all the time,
circulating the air, Cooling starts only if the room temperature risesabove the
coolness level selected on the TEMP Control, and stops once the set coolness
level is reached This setting gives the most even room temperatures

POWER SAVER MODE (some models)
The POWERSAVERMODE can save energy In this setting, the fan will not run
unless the TEMP Control is set cofder than the room temperature,. When the
TEMP Control is set coIder than room temperature, the air conditioner will
begin to circulate the air in the room Cooling wilf begin in about 3 minutes
The air conditioner turns off automatically when the room reaches the level of
coolness selected, H1GHCOOL is for fast cooling, MED COOL is for normal
cooling, and LOW COOL is for quiet cooling

HEAT (some models)

The HEAT selection provides quiet, efficient circulation of warm air Turn the

selector to the HEAT setting and set the thermostat to the warmest setting

When the HEATsetting is selected, the thermostat maintains the temperature by

automatically turning the heater on and off in response to room tempera-
ture Once the room iswarm, adjust the thermostat to a cooler setting The

fan runs continuously to circulate air in the room

VENT

MODE TEMP CLOSED

OFF • 5 g

HIGH _\ FAN 3_f_--_

COOL I : \)ONLY = •

I 9

MED \ _ / POWER COOLER

COOL_ SAVER _ EXHAUST

LOW

COOL

HEAVYDUTY

Side Air Model Control Panel

6

Conditioner Features

(continued)

FIG. 1 (OFF)

FIG 2 (FRESHAIR)

FIG 3 (VENT)

A slight heat odor may come from the unit when first switching to HEAT after
the cooling season is over this odor, caused by fine dust particles on the
heater, will disappear quickly.

Vent Control

The Vent Control allows the air conditioner to either recirculate inside air
(CLOSED)or exhaust air to the outside (OPEN)

• The CLOSEDposition is used when maximum cooling is desired. It may also
be used for air recirculation without cooling when the air conditioner is set
in the FAN position

• The OPENposition removes stale air from the room and exhausts it to the
outside. Fresh air is drawn into the room through normal air passages
found in homes,

° The OPENor CLOSED position can be used with any fan selection.
° For compact models, push the slide in to CLOSE, pull out to OPEN

Fresh Air Vent Control

The FreshAir Vent allows the air conditioner to recirculate inside air (OFF),
draw air into the room (FRESHAIR) or exhaust stale air to the outside (VENT)
See Figures 1,2 & 3 for this operation,

Air Directional Louvers

The air directional louvers control the air flow direction Adjust louvers up,
down, left or right, The outside tabs adjust the air up or down The center

levers direct the air Leftor right

Care and Cleaning

Figure I /

Clean your air conditioner occasionally to keep it looking new Besure to unplug
the unit before cleaning to prevent shock or fire hazards.

Air Filter Cleaning

The air filter should be checked at least once a month to seeif cleaning is necessary
Trapped particles in the filter canbuild up and cause an accumulation of frost on the

cooling coils Theseconditions reducecooling capacity Thereare two types of filters:
the rigid filter and the floppy filter

Models with rigid filters allow you to remove the filter without removing front:
o Some models, push the vent control handle to the OFFposition Lift the filter straig ht

up and out (Figure 1)

Care and Cleaning cont.

® ®

Figure 2

Figure 3

Remove
Knobs

Press firmly on each side of
case to reIease locking tabs

Figure 4

Removing Decorative Front - SomeModefs

Front

Retaining

Screws

Figure 5

SliderCasement Front

° 6-way louver models haveaslideout filter Graspthe formed handle of thefilter and

pull it to the left, removing it from the front panel (Figure 2).

° Formost installations in the window, this front may need to be removed to access

the filter for cleaning (Figure3). To removethe front, reversethe installation process
for SideAir Discharge Models shown in Front Installation.

o Somemodels require the louversto be tilted in the up position, before pulling the

filter out Placethe thimb under the center handle and pinch the top of the filter bar
with your forefinger while pulling the filter up and out as shpwn in Figure 6

Washfilter usingaliquiddishwashing detergent andwarm water. Rinsefilter thoroughly

Gently shake excesswater from the filter Dry filter thoroughly before replacing

Cabinet Cleaning

o Besureto unplug the air conditioner to prevent shock orfire hazard Thecabinet and

front maybedustedwith anoil-free cloth orwashedwith aclothdampenedin asolution
of warm water and mifdliquid dishwashingdetergent, Rinsethoroughly and wipe dry

° Neveruse harsh cleaners,wax or polish on the cabinet front.
. Besure to wring excesswater from the cloth before wiping around the controls

Excesswater in or around the controls may cause damage to the air conditioner

. The cabinet front can be removed for more thorough cleaning Referto "Front

Installation" in this manual and Figures 4 and 5.

• Clean the front in a sink using liquid dishwashing detergent and warm

water Rinsethoroughly and dry Be careful not to disturb soft sealson the front
. Replacecabinet front. Replacethe screwsor hex nuts
. Replacefront panel and filter Plugin air conditioner

Decorative Front and Dial Plate Removal

1. Unplug power cord from the wall outlet

2 Removeknobsbypullingfirmfy,andthen removedialplate,Removefront retainingscrew

from the front (seeFigure4 or 5 for screwlocation,whicheverissimilarto your model)

3. Pressfirmly on each sideof the metal casecloseto the front, approximately half way

down for Figure4, or 2/3 the way down from Figure5 from the top of the front
4 While pressing on the sides of the metal case, gently pull the front out and lift

up to release it from the case,

To reinstall:

Properreinstallation of decorative front isimportant for both safety and performance
2 Position the top of the decorative front on the top flange of the case and align

the tabson the front with the slots in the case On some models remove the filter
to expose the two (2) front retaining screws

3. Carefully pull down on the front to engage the top tabs while pushing the front
over the caseto ensure proper alignment. The side locking tabs will "click" when
the front is properly installed

4 Install the front retaining screw (see Figure 4 or 5 for screw location, whichever

issimilar to your model).

5. Installthe knobs by aligning them with their shafts and pushing firmly into place

Winter Storage

Ifyouptanto storetheairconditionerduringthewinter, removeit carefullyfromthe window
accordingtotheinstallation instructions Coveritwith plasticor returnktotheoriginal carton
NOTE: To prevent rust or electrical connectionsfrom being damaged, store air
conditionerinanupright position and adry place. A wintercovercanbepurchasedfrom

!ourdealerThecoverwill protectthe airconditionerwhenitisleftin_lacethroughthewinter

3 Putt Fitter Out and Up

1 Tilt Louver

Up

Louver

2 Pinch Center

Handle Here

Routine Maintenance

Winter Storage

if you plan to store the air conditioner during the winter, remove it carefully from
the window according to the installation instructions. Cover it with plastic or
return it to the original carton_ NOTE: To prevent rust or electrical

connections from being damaged, store air conditioner in an upright
position and a dry place. A winter cover can be purchased from your dealer

The cover will protect the air conditioner when it isleft in place through the
winter.

Before performing any service, unplug the power cord

from the electrical outlet.

After servicing, reverse the following procedures to reinstall the air
conditioner.

Cleaning the Cabinet Front

Removethe front panel. Wash with warm, sudsywater, Rinseand dry with. a soft
doth_ Neverusesolvents, cleaning fluids, abrasive cleaners or strong detergents _if
the packaging leavesa gum residue, removewith a cloth dipped in rubbing
alcoholr

Repairing Paint Damage

Inspect weather-exposed parts (cabinet shell, mounting hardware, if used, etc,)
once or twice ayear, especially in areas near oceans or where rust is a problem If
needed, touch up with a good grade of exterior paint.

Cleaning Inside the Air Conditioner

FI_ No Liquid should get into the motor, electrical control box, or

compressor electrical terminals,

1. Remove front panel

2. With help and using the proper lifting methods to avoid personal injury,
remove the chassis from cabinet shelL* When removing the air
conditioner from cabinet shell or window, there may be water inside the

base that may spill on the floor., Be careful to avoid cuts from sharp metal

-fins on the front and rear coils

3. Liquids should not get into electrical parts. Wrap the fan motor, electrical
control box, and electrical terminals in plastic_This wilt keep water or
other liquid from getting insidewhere it could damage the insulation and
cause serious trouble.

4, Clean and hose out base, coils, and water pans_Clean at least once a year

or more often if the coils and pans collect dirt, sand, leaves, algae, or

insects.

5, After cleaning, remove plastic protection, Wait 24 hours before starting

the unit again° This allows time for all areas to dry out.
NOTE: Water from rainfall or from normal use does not harm these

components since the water is not as forcefully driven into parts as a
stream of water from a garden hose°

*HANDLE NOTE: if the air conditioner has a chassis handle, it is NOT intended for
lifting the unit, it is for sliding the chassis WITHIN the cabinet shell only (to aid in
cleaning, maintenance, etc,)

Room Air Conditioner Troubneshoo ing Guide

®

THE AIR CONDITIONER WILL NOT OPERATE

Check if...

The power supply cord is unplugged

I A household fuse has blown or circuit breaker

ped

Then,.,

Firmly plug the cord into a five outlet with proper voltage
Replace the fuse or reset the circuit Make sure the unit is plugged into a

properly grounded receptacle as described in the Owners Manual
provided with the unit..

Set Fan Control to the desired setting.

THE UNIT BLOWS FUSES OR TRIPS CIRCUIT BREAKER
Check if... Then...

IToo many appliances are being used on the Unplug or relocate appliances that share the sa_ne circuit

{An extension cord is being used with the unit.

The unit is being restarted immediately after

[turn ng off cooling circuit

THE AiR CONDITIONER TURNS ON AND OFF, OR DOES NOT COOL ROOH
Check if...

The filter isdirty or obstructed by debris

The coils are dirty or obstructed by debris Check

both inside evaporator and outside condenser

coils

There is excessive moisture or heat in the room

being cooled (cooking, hot showers, etc.)
The Fan Control is on a Power Saver/Energy

Saver setting.
The Vent Control is set to OPEN or EXHAUST.

The Temperature Control is not at a cool enough
setting.

Do not use an extension cord to run the air conditioner.

Wait three minutes after turning off cooling circuit before trying to restart

uniL

Then.,.

Clean filter using a vacuum cleaner or wash filter in warm water and a

mild detergent. Dry thoroughly before reuse.
Call the local Sears store to inspect and clean the coils and condensate

water passages OR If familiar with electrical appliances
perform the required cleaning by carefully following the maintenance

• t .

instructions provided wLth the umt

Use exhaust vent fans while cooking or bathing and try not to use
heat-producing appliances during the hottest part of the day,

Use NORMAL settings for best comfort When the Power Saver settings
are in use, the fan does not circulate the room air continuously.

Set the Vent Control to CLOSED for maximum cooling.
Set the Temperature Control to a cooler setting

WATER DRIPS FROH THE CABINET INTO THE HOUSE

Check if... Then...

I The unit is not leveled properly The unit should Level the air conditioner to provide a 1/4" downward slope to the outside

slope slightly downward to the outside (½ bubble on carpenter's level) to provide proper drainage Reposition orshim the cabinet as necessary DO NOT drill a hole in the drain pan.

THE AIR CONDiTiONER SEEHS TO RUN TOO HUCH

Check if... Then...

The current unit replaced an older model The use of more efficient components may cause the unit to run longer

than an older model, but the total eilergy consumption will be less, Newer
units do not emit the "blast" of cold air you may be accustomed to from
older units, but this IS NOT an indication of lesser cooling capacity or
efficiency, Refer to the efficiency rating (EER) and capacity rating (in
BTUs) marked on the unit,

The unit is in a heavily occupied room or heat- Use exhaust vent fans while cooking or bathing. Try not to use heat-
producing appliances are in use in the room. producing appliances during the hottest part of the day A higher capacity,

unit may be required depending on the size of the room being cooled.

TYPICAL AIR CONDITIONER SOUNDS

Condenser- You may hear droplets of water hitting

the condenser, causing a "pinging" or "clicking" sound

Unit Vibration- The unit may vibrate and make noise

because of poor wall or window construction.

Fan- You may hear air movement from the fan

YOU HAY HEAR:

Compressor- The modern high efficiency compressor may have
a high pitched hum or pulsating noise that cycles on and off.

Thermostat- As the cooling system cycles, the thermostat

may click

D1817 TP 5-54 - Room Air Conditioner Troubleshooting Guide - Revision "A" - March 18, 1996 - Page I of 1

© Sears, Roebuck and Co,

10

Warranty

WARRANTY
Full One-Year Warranty on Air Conditioner

For one year from date of purchase, when this air conditioner is operated and
maintained for normal room cooling according to instructions in this
owner's manual, Sears will repair it, free of charge, if defective in material or
workmanship

Full Five-Year WarrantY on Sealed Refrigeration System

For five years from the date of purchase, when this air conditioner is operated
and maintained for normal room cooling according to instructions in this
owner's manual, Sears will repair the sealed refrigeration system (consisting of
refrigerant, connecting tubing, and compressor), free of charge, if defective in
material or workmanship

Warranty Service
Warranty service is available by contacting the nearest service center in the
United States

This warranty gives you specific legal rights, and you may have other rights
which vary from state to state

SEARS, ROEBUCK and CO. Dept. 817WA, Hoffman Estates, IL 60719

Sears Service

Maintenancp Agreement

"We Service What We Sell" is our assurance you can depend on Sears
for service Your air conditioner has added value when you consider
that Searshas service units nationwide, staffed with professional technicians

trained on all appliances Sears sells, They have the knowledge and skills, tools,

parts, and equipment to insure our pledge to you that "We Service What We

Sell,"

Sears Maintenance Agreement

Maintain the value of your air conditioner with a Sears Maintenance

Agreement Searsair conditioners are designed, manufactured, and tested for
years of dependable operation Yet, any modern appliance may require

service from time to time The Sears Maintenance Agreement offers you an

outstanding service program for your air conditioner

The Sears Maintenance Agreement

o Is your way to buy tomorrow's service at today's price

= Eliminates repair bills resulting from normal use,

• Allows for as many service calls as required

• Provides an annual Preventive Maintenance Check at your request to
keep your Air Conditioner in proper running condition,

For more information, call 1-800-827-6655