Sears CrossWalk 831.297364,CrossWalk User Manual

ER O

I I IIIIIIIIIII IIII II I I II

SE / S

Model No. 831_9_64
Serial No.

The sedalnumberisfoundinthelocation

shownbelow.Writetheserialnumberin
theSPaCeabovefor futurereference.

Sedal Number

E_X E£: RC I S E_

EQUIPMENT

HELPLINE!

1-800-736-6879

USER'S MANUAL

SEARS, ROEBUCK AND CO, HOFFMAN ESTATES, IL 60179

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS ................... .

ASSEMB'_'.......... :::: :: :::: ::

°1_ • 1oooo ,o °°o o.°. °_°o o_

OPE_TION AND ADJUSTMENT .................

HOW TO FOLD AND MOVE THE TI:I_DMIIA- ......

TROUBLE,.SHOOTING .........................

CONDITIONING GUIDELINES .......................................... . . .

IolqoooleQo=oog_

!........."........7••

....... 10

• *o_o II • •

.... 12

................. 14

ORDERING REPLACEMENT PARTS ........... Back Cover

• =.o ,,,,t • • • ,,,_•,_ Q o J ... *•I*Q Q ° •• ° aqa•

FULL 90 DAY WARFI.q_ ............... Back Cover

Note: A HARDWARE IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART UST and am attached
to the center of this manual. Please save them for future reference.

IMPORTANT PRECAUTIONS

2

Thedecalshownattherighthasbeen
placedonyourtreadmill.Ifthedecalis
missing_orif it isnotlegible,pleasecall

ourtoll-freeHELPLINEtoorderafreere-
placementdecal(seethebackcoverof

thismanual).Applythedecalintheloca-
tionshown.

AWARNING!

• Storage latch must be
fully engaged before
treadmill is moved or

stored.

° °II

© 1

° °11

3

BEFORE YOU 13EGIN

Thank you for selecting the PROFORk, P CROSS-
WALK SI treadmill. The CROSSWALK SI treadmill

blends advanced technology with Innovative design to

let you enjoy an excellent form of cardiovascular exer-
cise In the convenience and pdvacy of your home.

For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our toU-free HELPUNE at 1-800-736-6879,
Monday through Saturday, 7 a.m. until 7 p.m. Central

Time (excluding holidays). To help us esslst you,
please note the product model number and Serial num-
ber before calling. The model number ofthe treadmill

is831.297364. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).

Before reading further, please mvtew the drawing
below and familiarize yourself with the pads that are
labeled.

Rack

BACK

AccessoryTray

Handrails

WalldngBelt_

FootRails

"Bottle

Holder(Water

Boffieisnct

Induded)

Upper Body

Arms

FRONT

Rear Roller

Adjustment Bolt

Platform

RIGHT SIDE

4

ASSEMBLY

CAUTION: Read and follow step I below before rernovlng the restraining Ue (sep cl_'a_ng "1).ff the restrain-
ing tie Is removed prematurely, serious bodily injury may result. Assembly requires _v/o people.. Set the tread-

mill in a cleared area and remove the packing materials except for the restraining tle"Do notdispose of the
packing materials untilassembly Iscompleted. Use the HARDWARE IDENTIRC_.TION CHART in the center of
this manual to identify the partsused inassembly. Assembly requires the Included allen wrench L==-, a
phillips screwdriver ..==_, and two adjustable wrenches G_==:_.

1. Slide the Left Upright (1) onto the left side of the Base
(59). It may be necessary to firmly push down on the
Left Upright until it Is fully seated on the Base.
Remove the restrainingtie from the Base.

Attach the left handrailto the Base (59) witha Handrail
Bolt(93), 3/8" Washer (67), and Handrail Nut (4). Do not

tighten the Handrail Bolt yeL Using the allen wrench,
tighten two Upright Screws (63) with two of the four

Updght Washers (111) intothe Left Updght (1) and Base. Restralnlng

2. Slide the Right Upright(44) onto the right side of the
Base (59). It may be necessary to firmly push down

on the Right Upright until it is fully seated on the
Base. Be careful not to pinch the Wire Harness (25)

between the Right Updght and the Base.

Attach the right handrail to the Base (59) with a Handrail

Bolt (93), 3/8" Washer (67), and Handrail Nut (4). Do not
tighten the Handrail Bolt yet. Using the allen wrench,
tighten two Updght Screws (63) withthe remaining Upright
Washers (111) into the Right Upright (44) and Base.

Hand tighten the Handrail Nuts (4) used insteps I and 2.

Using a wrench, tighten the Handrail Bolts (93) used in
steps I end 2.

Remove the wire ties (not shown) attaching the Console

Base (9) to the Right Upright (44).

3. Set the Console Base (9) on the Left and Right Updghts

(1, 44).

While one person carefully fesds any slack Wire Hamess

(25) down intothe Right Upright (44), a second person

should carefully pullthe slackWire Hamess from the

lower end of the Right Upright.

Attach the Console Base (9) with four Screws (75).

Align the holes in the Book Rack (62) with those in the

Console Base (9). Attach the Book Rack to the Console

Base with four Screws (75) as shown.

75

6

4. With the help of a secondperson, carefully lower the Left

and Right Uprights(1, 44) until the handrails are resting
on the floor.

. Attach six Base Pads (57) to the bottom of the Base (59)

in the indicated locations.Note: An extra Base Pad may

be included.

(See drawing 4 above.) With the help of a second person,
raise the Left and Right Uprights (1, 44) until the Base

(59) is resting flat on the floor.
Before moving the treadmill, see HOW TO MOVE THE

TREADMILL on page 11.

So

Remove the Resistance Knob (97), 3/8" Washers (67),

Spdng Washer (5), Thrust Washers (101), Thrust Bearing

(102), and Resistance Cone (98) from the Resistance
Boll (105). Be sure to keep all parts in order. Insert one
of the Upper Body Arms (96) into the Resistance Cone
(98), making sure that it is turned as shown. Slide all
parts back onto the Resistance Boll (105). Refer to the
HARDWARE IDENTIFICATION CHART to make sure

that all partsare in the correct order. Tighten the

Resistance Knob (97) onto the Res!stance Boll

Insert two Resistance BracketBolts (107) with Bracket

Washers (70) into the LeftUpdght (1). Slide two Star

Washers (103), a Spacer (106), and two more Star
Washers (103) onto the Bolts.Tighten the Bolts into the

:Resistance Bracket (104). (Note: It may be necessary to

loosen the Resistance Knob [97] and pivotthe
Resistance Bracket.)

.

Attach the other Upper BodyArm (96) as descn'bed
above. Make sure that bothUpper Body Arms are in the
position shown on page 4. Feed the slack Wire Harness
(25) into the Base (59).

Remove the backing from the Adhesive Clip (77). Press
the Adhesive Clip onto the Rear Roller Endcap (78) in the
indicated location. Press the AllenWrench (76) into the
Adhesive Clip.

Make sure that all parts are tightened before you use the

treadmill. Note: To protect the floor or carpet, place a

mat under the treadmill. For information on ordering a
mat, see REPLACEMENT PARTS on the back cover.

. •

7

44

105

78

59

Body

Arm must be
tumed in this
direction

104 --96

102

97

76