Sears 83.121.600.00 User Manual

Sears Model No. 831,21600.0 Kmart Model No. WLEX1076.0

Serial No,

Write the serial number in the space above for future reference.

Serial Number Decal

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you have questions, PLEASE CONTACT

OUR CUSTOMER SERVICE DEPARTMENT DIRECTLY.

USER'S MANUAL

SEARS CUSTOMERS:

1-800-4-MY-HOME ®

(1-800-469-4663) KMART CUSTOMERS:

1-866-699-3756

Mon.-Fri., 6 a.m.-6 p.m. MST

www.wesIo.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS ....

BEFORE YOU BEGIN ....

ASSEMBLY ....

HOW TO OPERATE THE EXERCISE CYCLE MAINTENANCE AND TROUBLESHOOTING CONDITIONING GUIDELINES

PART LIST ......

EXPLODED DRAWING ....

ORDERING REPLACEMENT PARTS . .

LIMITED WARRANTY ....

IMPORTANT PRECAUTIONS

&WAR NING: To reduce the risk of serious injury, read the following important precau-

tions before using the exercise cycle.

1. Read all instructions in this manual and all

warnings on the exercise cycle before using the exercise cycle. Use the exercise cycle only

as described in this manual.

2. It is the responsibility of the owner to ensure that all users of the exercise cycle are ade-

quately informed of all precautions.

3. The exercise cycle is intended for home use only. Do not use the exercise cycle in a commercial, rental, or institutional setting.

Use the exercise cycle indoors on a level sur- face. Keep the exercise cycle away from

moisture and dust. Place a mat under the exercise cycle to protect the floor. Make sure

that there is enough clearance around the exercise cycle to mount, dismount, and use the exercise cycle.

5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.

6. Keep children under the age of 12 and pets away from the exercise cycle at all times.

7. Wear appropriate clothes when exercising; do not wear loose clothes that could become

caught on the exercise cycle. Always wear athletic shoes for foot protection.

8. The exercise cycle should not be used by persons weighing more than 250 pounds.

9. Always keep your back straight while using the exercise cycle; do not arch your back.

10.

If you feel pain or dizziness while exercising, stop immediately and cool down.

11.

The exercise cycle does not have a free wheel; the pedals will continue to move until the flywheel stops.

12.

The pulse sensor is not a medical device. Various factors, including the user's move- ment, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general.

13.

The warning decal shown on page 3 has been placed on the exercise cycle. If the decal is missing or illegible, call the toll-free tele- phone number on the front cover of this man- ual and order a free replacement decal. Apply

the decal in the location shown.

• • 2 3

4 8

• 15

Back Cover Back Cover

WAR NING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

BEFORE YOU BEGIN

Congratulations for selecting the new WESLO ®

PURSUIT 350 exercise cycle. Cycling is one of the most effective exercises for increasing cardiovascular fitness, building endurance, and toning the body. The

PURSUIT 350 exercise cycle offers a selection of fea- tures designed to let you enjoy this healthful exercise in the convenience and privacy of your home.

For your benefit, read this manual carefully before you use the exercise cycle. If you have questions

Handlebar

• i_isuse of this machine may result in serious

injury.

• Read user's manual

priorto use and fonow

all warnings and

instructions,

, Do not allow children

on oraround machine,

• Pedals continue to spin when you stop

pedaling.

• Spinning pedals can cause injury.

= Reduce pedal speed

in a controlled manner,

• User weight must not exceed 250 pounds.

• Replace label if damaged, illegible, or

removed,

Thumb Pulse Senso_

after reading this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting

us. The model number is found on the front cover of this manual. The serial number is found on a decal

attached to the exercise cycle (see the front cover of this manual for the location of the decal).

Before reading further, please review the drawing

below and familiarize yourself with the labeled parts.

Console

Resistance Knob

Seat

Seat Knob

REAR

FRONT

Pedal/Strap

RIGHT SIDE

ASSEMBLY

Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the packing

materials. Do not dispose of the packing materials until assembly is completed. Assembly requires the includ- ed tools and your own adjustable wrench _, Phillips screwdriver _ _, and

pliers _. Use the drawings below to identify the small parts used for assembly. The number in parentheses below each

drawing is the key number of the part, from the PART LIST on page 14. The number following the key number is the quantity needed for assembly. Note: Some small parts may have been preassembled. If a part is not in the parts bag, check to see if it has been preassembled.

M4 x 25mm Round Head Screw (41)-3

M8 x 60mm Button

Screw (30)-4

1. Insert the Rear Stabilizer (6) into the Frame (1). Attach the Rear Stabilizer with four M8 x 60mm

Button Screws (30).

2. Orient the Front Stabilizer (2) with the large holes facing the Frame (1). Attach the Front Stabilizer to the Frame with two M8 x 73mm Button Screws (33).

M8 Split M8 Nylon

Washer (42)-7 Locknut (10)-4

M6 x 15mm Button M8 x 15mm Sutton

Screw (46)-4 Screw (34)-3

M8 x 73mm Sutton

Screw (33)-2

Large Holes 1

3. AttachtheLeftandRightUprightCovers(14,15)

aroundtheFrame(1)withthreeM4x25mmRound HeadScrews(41)asshown.

4. AttachtheSeat(12)totheSeatPost(5)withfour

M8SplitWashers(42)andfourM8Nylon Locknuts(10).Note:TheSplitWashersandthe

Nylon Locknuts may be pre-attached to the underside of the Seat,

5. Turn the Seat Knob (9) counterclockwise and remove

it from the Frame (1). Next, insert the Seat Post (5) into the Frame. Adjust the Seat Post to the desired height and insert the Seat Knob (9) through the indi-

cated hole in the Frame into one of the adjustment

holes in the Seat Post. Then, turn the Seat Knob

clockwise until it is tight. Make sure the Seat Knob

is firmly engaged in one of the adjustment holes in the Seat Post,

ustment

Holes

+ 11 hidden pages