Sears 61118, 71061, 71068, 71161, 71168 Owner's Manual
...
SEARS
GAS
RANGE
OWNER'S
MANUAL
Model Numbers:
61011 72296
61018 72298
61061 72751
61111 72755
61118 72758
71061 75171
71068 75181
71161 75188
71168 75271
71351 75275
71358 75276
71661 75278
71665 75281
71668 75291
_71751 75295
71758 75296
72291 75298
72295
Safety Instructions
Anti-Tip Device 2, 3,3I, 39
Important Safetylnstr_ctions 2-6
Care & Maintenance
BeforeYou Call for Service 40, 41
Care and Cleaning 22-28
Consumer Services 42, 44
Repair Services 42
Thermostat Adjustment 17
Warranty 43
Installation Instructions
Air Adjustment 36,38
Anti-Tip Device 3I, 39
Connect the Rangeto Gas 32-34
Dimensions & Clearances 29
Electrical Connections 34,35
LP 39
Operation
Featuresof Your Range 7
Baking 15,16
Broiling!Broiling Guide 20, 2
Clock andTimer 12
Roasting,Roasting Guide I8, 19
Surface Cooking 8-11
Caution:
Read and Follow
All Safety Rules
and Operating
Instructions
Before First Use
of This Appliance.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
tg3D558(]P052
5R4244
4_7 CG
Important Safety Instructions
Read all instructions before using this appliance.
WARNING: If the information in this manual
is not followed exactly, a fire or explosion may
result causing property damage, personal
injury or death.
--Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
--WHAT TO DO IFYOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppliers
instructions.
• If you cannot reach your gas supplier, call
the fire department.
--Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
IMPORTANT SAFETY NOTICE
• The California Safe Drinking Water and Toxic
Enforcement Act requires the Governor of
California to publish a list of substances known to
the state to cause cancer, birth defects or other
reproductive harm, and requires businesses to warn
customers of potential exposure to such substances°
Gas appliances cause minor exposure to four of
these substances, namely benzene, carbon
monoxide, formaldehyde and soot, caused primarily
by the incomplete combustion of natural gas or LP
fuels. Properly adjusted burners, indicated by a bluish
rather than a yellow flame, will minimize incomplete
combustion. Exposure to these substances can be
minimized further by venting with an open window
or using a ventilation fan or hood..
° Fluorescent light bulbs and safety valves on
standing pilot ranges contain mercury. If your
model has these features, they must be recycled
according to local, state and federal codes.
When You GetYour Range
A WARNTN G
. ALL RANGES C_N TIP
" INJURY TO PERSONS
COULD RESULT
• INSTALL ANTI-TIP
DEVICES PACKED
WITH RANGE
° SEE INSTALLATION
INSTRUCTIONS
Have the installer show you the
location of the range gas shut-off
valve and how to shut it off if
necessary.
Have your range installed and
properly grounded by a qualified
installer in accordance with the
Installation Instructions. Any
adjustment and service should be
performed only by qualified gas
range installers or service technicians.
Plug your range (electric ignition models only)
into a 120-volt grounded outlet only. Do not remove
the round grounding prong from the plug. If in doubt
about the grounding of the home electrical system, _it
is your personal responsibility and obligation to have
an ungrounded outlet replaced with a properly
grounded, three-prong outlet in accordance with the
National Electrical Code. In Canada, the appliance
must be electrically grounded in accordance with the
Canadian Electrical Code, Do not use an extension
cord with this appliance.
* Do not attempt to repair or replace any part of
your range unless it is specifically recommended
in this manual. All other servicing should be
referred to a qualified technician,
" Be sure al! packing materials are removed from
the range before operating it to prevent fire or
smoke damage, should the packing material ignite.
* Locate the range out of kitchen traffic path and
out of drafty locations to prevent pilot outage
(on models with standing pilots) and poor air
circulation.
• After prolonged use of a range, high floor
temperatures may result and many floor coverings
will not withstand this kind of use. Never install
the range over vinyl tile or linoleum that cannot
withstand such type of use. Never install it directly
over interior kitchen carpeting,
• Be sure your range is correctly adjusted by a
qualified service technician or installer for the
type of gas (natural or LP), that is to be used.
Your range can be converted for use with either type
of gas_ See the Installation instructions.
WARNING: These adjustments must be made by a
qualified service technician in accordance with the
manufacturer's instructions and all codes and
requirements of the authority having jurisdiction.
Failure to follow these instructions could result in
serious injury or property damage. The qualified
agency performing this work assumes responsibility
for the conversion.
UsingYour Range
• Do not leave children
alone or unattended
where a range is hot or
in operation. They could
be seriously burned.
• Do not allow anyone to
climb, stand or hang on
the door, storage or
broiler drawer (on some models) or cooktop. They
could damage the range and even tip it over, causing
severe personal injur_
Let the burner grates and other surfaces cool
before touching them or leaving them where
children can reach them.
CAUTION: ITEMS OF
INTEREST TO CHILDREN
SHOULD NOT BE STORED
IN CABINETS ABOVE A
RANGE OR ON THE
BACKSPLASH OF A
RANGE---CHILDREN
CLIMBING ON THE
RANGE TO REACH ITEMS
COULD BE SERIOUSLY INJURED.
aWARNIN
All rangescan tip and injury could
result. To prevent accidental
tipping of the range, attach it to the
wall and floor by installing the Anti-
Tip device supplied_
To check if the device is installed and
engaged properly, carefully tip the
range forward. The Anti-Tip device
should engage and prevent the range
from tipping over.
If you pull the range out from the wall for any reason,
make sure the device is properly engaged when you push
the range back against the walt. If it is not, there is a
possible risk of the range tipping over and causing injury
if you o_ a child stand, sit or lean on an open door.
Please refer to the Anti-Tip device information in this
manual. Failure to take this precaution could result in
tipping of the range and injury.
* Never wear loose fitting :_ "_.,:.:
or hanging garments _D[ \ :':'"
while using the
appliance. Be careful
when reaching for items
stored in cabinets over
the cooktopo Flammable
material could be ignited if' brought in contact with
flames or hot oven surfaces and may cause severe bums.
(continued next page)
Important Safety Instructions (co0 0u0d)
• Do not use water on grease
fires. Never pick up a
flaming pan. Turn the
controls off. Smother a
flaming pan on a surface unit
by covering the pan
completely with a well-fitting
lid, cookie sheet or flat tray.
Use a multi-purpose dry
chemical or foam-_,pe fire
extinguisher.
Flaming grease outside a pan can be put out by
covering it with baking soda or, if available, by using
a multi-purpose dry chemical or foam-type fire
extinguisher.
Flame in the oven can be smothered completely
by closing the oven door and turning the oven off or
by using a multi-purpose dry chemical or foam-type
fire extinguisher_
• Do not store flammable
materials in an oven,
range broiler or storage
drawer, or near the
cooktop.
• Do not store or use
combustible materials, gasoline or other
flammable vapors and liquids in the vidnlty of
this or any other appliance.
• Do not let cooking grease or other flammable
materials accumulate in or near the range.
• When cooking pork, follow the directions exactly
and always cook the meat to an internal temperature
of at least 170°E (77°C,). This assures that, in the
remote possibility that trichina may be present ia the
meat, it will be killed and the meat wi_ be safe to eat°
• For your safety; never use
your appliance for
warming or heating the
room,
Surface Cooking
* Always use the LITE position (on models with
electric ignition) or the HI position (on models
with standing pilots) when igniting the top
burners and make sure the burners have ignited.
• Never leave the surface burners unattended at
high flame settings. Boilovers cause smoking and
greasy spillovers that may catch on fire°
* Adjust the top burner flame size so it does not
extend beyond the edge of the cookware. Excessive
flame is hazardous°
• Use only dry pot holders--moist or damp pot
holders on hot surfaces may result in burns from
steam,
* Do not let pot holders come near open flames
when lifting cookware. Do not use a towel or other
bulky cloth in place of a pot holder.
, To minimize the possibility" of burns, ignition of
flammable materials and spillage, turn cookware
handles toward the side or back of the range without
letting them extend over adjacent burners,
o Always mm the surface burners to OFF before
removing cookware,
Carefully watch foods being fried at a high flame
setting.
• Never block the vents (air openings) of the range.
They provide the air inlet and outlet that are
necessary for the range to operate properly with
correct combustion. Air openings are located in the
following places:
--Oven vent at the rear of the cooktop,
---Mr intake under the broiler drawer°
---_r vent at the top of the oven door,
" Do not use a wok on models with sealed burners
ff the wok has a round metal ring that is placed
over the burner grate to support the wok. This
ring acts as a heat trap, which may damage the
burner grate and burner head. Also, it may cause the
burner to work improperly. This may cause a carbon
monoxide level above that allowed by current
standards, resulting in a health hazard_
° Foods for frying should be as dry as possible.
Frost on frozen foods or moisture on fresh foods can
cause hot fat to bubble up and over the sides of the pano
• Use the least possible amount of fat for effective
shallow or deep fat frying. Filling the pan too ful!
of fat can cause spillovers when food is added.
° If a combination of oils or fats will be used in
flying, stir together before heating or as fits melt
slowly_
° Always heat fat slowly and watch as it heats.
• Use a deep fat thermometer whenever possible to
prevent overheating fat beyond the smoking point.
• Never try to move a pan of hot fat, especially a
deep fat fryer. Wait unti! the fat is cool
° When using glass cookware, make sure it is
designed for top-of-range cooking.
• Use proper pan size. Avoid pans that are unstable or
easily tipped. Select cookware having fiat bottoms
large enough to properly contain food and avoid
boilovers and spillovers and large enough to cover
burner grates. This will both save cleaning time and
prevent hazardous accumulations of food, since heavy
spattering or spillovers left on the range can ignite.
Use pans with handles that can be easily grasped and
will remain cool
Do not leave any items on the cooktop. The hot
air from the vent may ignite flammable items and
will increase pressure in closed containe:s, which may
cause them to burst.
" To avoid the possibility of a burn, always be
certain that the controls for all burners are at the
OFF position and all grates are cool before
attempting to remove them.
• When flaming foods axe under the hood, turn the
fan off. The fan, ff operating, may spread the flames.
If the range is located near a window, do not hang
long curtains that could blow over the top burners
and create a rite hazard.
° When a pilot goes out (on models with standing
pilots), you will detect a faint odor of gas as your
signal to relight the pilot, When retighting the pilot,
make sure the burner controls are in the OFF
position, and follow instructions in the Installation
Instructions to relight.
• If you smell gas, and you have already made sine the
pilots are lit (on models with standing pilots), turn
off the gas to the range and call a qualified service
technician. Never use an open flame to locate a leak.
(cantinued next page)
• Keep all plastics away
from the top burners.
• Do not leave plastic
items on the cooktop--
they may melt if left too
close to the vent°
Vent appearance and location vary
Important Safety Instructions (0o0 i0°0¢
Baking, Broiling and Roasting
* Do not use the oven for a storage area. Items
stored in the oven can ignite.
o Stand away from the range when opening the
door of a hot oven. The hot air and steam that
escape can cause burns to hands, face and eyes.
* Keep the oven free from grease buildup.
o Place the oven shelves in the desired position
while the oven is cool.
• Pulling out the shelf to the shelf-stop is a
convenience in lifting heavy foods. It is also a
precaution against burns from touching hot
surfaces of the door or oven walls. The lowest
position (R) is not designed to slide.
° Do not heat unopened food containers. Pressure
could build up and the container could burst,
causing an injury.
• Do not use aluminum foil anywhere in the oven
except as described in this manual. Misuse could
result in a fire hazard or damage to the range.
• When using cooking or roasting bags in the oven,
follow the manufacturer's directions.
" Use only glass cookware that is recommended for
use in gas ovens.
- Always remove broiler pan from the oven or the
broiler compartment as soon as you finish broiling.
Grease left in the pan can catch on fire if oven is used
without removing the grease from the broiler pan.
When broiling, if meat is too close to the flame,
the fat may ignite. Trim excess fat to prevent
excessive flare-ups_
* Make sure the broiler pan is in place correctly to
reduce the possibility of grease fires,
• If you should have a grease fire in the broiler pan,
turn the oven off and keep the broiler compartment
door closed to contain fire until it burns out,
CleaningYour Range
• Clean only parts listed in this Use and
Care Manual.
• Keep the range dean and free of accumulations of
grease or spillovers, which may ignite.
• Be careful when you clean the cnoktop because
the area over the pilot will be hot (for standing
pilot models).
• For continuous dean models, do not use oven
cleaners on any of the continuous deaning
surfaces. Continuous cleaning surfaces can be
identhqed by their rough surface finish.
SAVE THESE
INSTRUCTIONS
Features of Your Range
NOTE: Not all models have all features. Appearance of features varies.
¢
¢
O
¢
€
¢
!
lI II
!1 II
@
/_ umar CapDEp Pan
_ Burner Head
j
Your range is equipped with
one of the two types of surface
burners shown above,
0
0
Feature Index See Page
I Broiler Compartment .3, 4, 6, 20,
2I, 27, 38
2 Model and Serial Numbers
On front frame of range, behind
broiler compartment, storage
drawer or kick panel.
3 Anti-Tip Device 2, 3, 31, 39
4 Oven Bottom 27
5 Oven Shelves Easily removed 6, 14-I6,
or reposidoned on shelfsupports_ 18, 2I, 25
6 Oven Interior Light 13, 25
(on some models)
7 Oven Light Switch (on some models) I3
8 Surface Burners, Drip Pans 4, 5, 8-I 1,
(on some models), and Grates 22-24, 36, 37
9 Oven Vent (location varies) 5, I4, 25
Feature index See Page
I0 Clock and Timer 12
(on some models)
11 Lift-Up Cooktop 24
(on models with standard twin burners)
12 Surface Burner Control Knobs 4, 10, 1 I, 25
13 Oven Control Knob 13, 15,
t 7-20, 25
I4 Oven Shelf Supports 13-15, 18
I5 Lift-Off Oven Door 3, 20, 26
16 Installation Clearances Label
I7 Air Intake (under storage or broiler 25
drawer or kick panel)
I8 Broiler Pan and Grid 6, 18, 20,
2I, 25
Air Vents 5, 14, 25
How Does This Cooktop Compare to
Your Old One?
Your new cooktop has gas burnets. If you are used to
cooldng with induction or other electric surface units,
you wilt notice some differences when you use gas
burners°
The best types of coolcware to use, plus heat-up and
cool-down times, depend upon the type of burner or
surface unit you haven
The following chart will help you to understand the
differences between gas burner cooktops and any other
type of cooktop you may have used in the past.
Type of Cooktop
Gas Burners
Hectric Coil
@
Solid Disk
@
Radiant (Glass
Ceramic') Cooktop
O
Induction
Description
Regular or sealed
gasburners use
either LP gas
or natural gas,
Flattened metal
tubing containing
electric resistance
wire suspended
over a drip pan,
Solid cast iron
disk sealed to the
cooktop surface.
Electric coils
under a glass
ceramic cooktop.
High frequency
induction coils
under a glass
5urface_
How It Works
Flames heat the pans directly. Pan flatness is not critiol to cooldng results,
but pans should be well balanced. Gas burners heat the pan right away and
change heat settings right awa_ When you turn the control off, cooking stops
right away°
Heats by direct contact with the pan and by heating the air under the pan. For
best cooking results, use good quality pans, Electric coils are more forgiving
of warped pans than radiant or solid disks, Heats up quictdy but does not
change heat settings as quickly as gas or induction. Electric coils stay hot
enough to continue cooking for a short time afi:er they are turned off,
Heats by direct contact with the pan, so pans must be flat on the bottom for
good cooking results. Heats up and cools down more slowly than electric
coils, The disk stays hot enough to continue cooking after it is turned off',
Remove the pan from the solid disk if you want the cooldng to stop.
Heat travels to the glass surface and then to the cookware, so pans must be
flat on the bottom for good cooking results, The glass cooktop stays hot
enough to continue cooking after it is turned off. Remove the pan from the
surface unit if you want cooking to stop
Pans must be made of ferrous metals (metal that attracts a magnet). Heat is
produced by a magnetic circuit between the coll and the pan. Heats up right
away and changes heat settings right away. like a gas cooktop.. After turning
the control off, the glass cooktop is hot from the heat of the pan, but cooking
stops right away
Surface Cooking
Lighting Instructions for
Standing Pilot Models
The surface burners on these
ranges have standing pilots
that must be lit initially° To
light them:
1. Be sure the surface
burner control knobs are
in the OFF position.
2. Remove the grates and lift the cooktop up (see the
Lift-Up Cooktop section).
3. Locate the two pilot ports and light each of them
with a match.
NOTE: If the pilot is too high or low, you can adjust it.
See the Adjust the Surface Burner Pilots If' Necessary
section of the Installation Instructions.
4. Lower the cooktop. Your surface burners are now
ready for use_
5. Observe the lighted burners. Compare the flames to
pictures in the Problem Solver, If any flame is
unsatisfactory, ca]l for service.
Lighting Instructions for
Electric Ignition Models
Your surface burners are lighted by electric ignition,
eliminating the need for standing pilot lights with
constantly burning flames.
In case of a power failure, you can light the surface
burners on your range with a match. Hold a lighted
match to the burner, then turn the knob to the LITE
position. Use extreme caution when lighting burners
this way.
Surface burners in use when an electrical power failure
occurs will continue to operate normally,
The electrode of the spark igniter is exposed° When
one burner is turned to LITE, all the burners spark,
Do not attempt to disassemble or clean around any
burner while another burner is ono Am electric
shock may result, which could cause you to knock
over hot cookware_
(continued next page)
Surface Cooking (0o0 o0od
Surface Burner Controls
The knobs that turn the surface burners on and off are
marked as to which burners they control.
The two knobs on the left contro! the left front and
left rear burners° The two knobs on the right contro!
the right front and right rear burners.
On ranges with sealed burners:
" The smaller burner (right rear position) will give
the best simmer results. It offers precise cooking
performance for delicate foods, such as sauces
or foods which need to cook over !ow heat for a
long time. It can be turned down to a very low
simmer setting.
• The right front burner is higher powered than the
others and will bring liquids to a boil quicker
(natural gas installations only).
Before Lighting a Burner
• Ii:drip pans are supplied with your range, they
should be used at aB times.
• Make sure all grates on the range are in place before
using a burner°
To Light a Surface Burner
Electric Ignition Models:
Push the control knob in and
turn it to LITE. You wilt hear
a little "clicking" noise--the
sound of the electric spark
igniting the burner.
Standing Pilot Models:
Push the control knob in and him it to HI position.
The burner should light within a few seconds°
After the burner ignites, turn the knob to adjust the
flame size.
Flame will be almost horizontal and will lift slightly
away from the burner when the burner is first
turned on. A blowing sound may be heard the first
few seconds. This normal sound is due to improved
injection of gas and air into the burner. Put a pan on
the burner before lighting it, or adjust the flame to
match pan size as soon as it !ights, and the blowing
sound will stop.
After Lighting a Burner
" After the burner ignites, turn the knob to adjust
the flame.
• Check to be sure the burner you turned on is the one
you want to use.
• Do not operate a burner for an extended period of'
time without cookware on the grate, The finish on the
grate may chip without cookware to absorb the heat.
• Be sure the burners and grates are coo! befbre you
place your hand, a pot holdez; cleaning cloths or
other materials on them,
t0
How to Select Flame Size
Watch the flame, not the knob, as you reduce heat.
The flame size on a gas burner should match the
cook'ware you are using.
FOR SAFE HANDLING OF _....
COOKWARE NEVER LET
THE FLAME EXTEND UP
THE SIDES OF THE
COOKWARE. Any flame larger than the bottom of the
cookware is wasted and only serves to heat the handle.
Top-of-Range Cookware
iidttminttm: Medium-weight cookware is
recommended because it heats quickly and evenly.
Most foods brown evenly in an aluminum skillet° Use
saucepans with tight-fitting lids when coo!ring with
minimum amounts of water.
G-st-Iron: If heated slowly, most skillets will give
satisfactory results.
Enamelware: Under some conditions, the enamel of
some cookware may melto Follow cook-ware
manufacturer's recommendations for cooking methods_
Glass: There are two types of glass coolcware----_ose
for oven use only and those for top-of-range cooking
(saucepans, coffee and teapots). Glass conducts heat
very slowl)_
Heatproof Glass Ceramic: Can be used for either
surface or oven cooking. It conducts heat very slowly
and cools very slowly° Check cookware manufacturer's
directions to be sure it can be used on gas ranges_
Stainless Steel: This metal alone has poor heating
properties and is usually combined with copper,
aluminum or other metals for improved heat
distribution_ Combination metal skillets usually work
satisfactorily if they are used with medium heat as the
manufacturer recommends.
Wok This Way
(on models with sealed burners)
We recommend that you use
a flat-bottomed wok. They
are available at your local
retail store.
A traditional round bottom wok can be used with
Wok Holder accessory, model JXWK which can be
ordered from your appliance dealer" The Wok Holder
fits on top of the range grate to provide support and
proper air circulation for traditional round bottom
woks onlyo Do not use flat bottomed woks with the
Wok Holder°
Do not use a wok on any .........
other support ring. Placing
the ring over the burner
grate may cause the burner
to work improperly, _!i::i_"
resulting in carbon
monoxide levels above allowable current standards.
This could be dangerous to your health. Do not try to
use such woks without the ring unless you are using
the Wok Holder. You could be seriously burned if the
wok tipped over.
Stove Top Grills
(on models with sealed burners)
Do not use stove top grills on
your sealed gas burners. If you
use the stove top grill on the
sealed gas burner it will cause '_!_.
incomplete combustion and
can result in exposure to
carbon monoxide levels above allowable current
standards° This can be hazardous to your health°
11
Clock and Timer (onsomomodo,s)
[ ;,2:=o]©
(appearance may vary)
Follow the directions below if your range has the clock
and timer shown above. You have the choice of having
the timer show the time counting down or the time of
day_ In either case, the timer will signal at the end of
the timer period to alert you that the time is up.
To Set the Clock
NOTE: When you first plug in the range or after a
power failure, the entire Clock/Timer display wii!
light up.
I. Press the CLOCK pad.
2. Press and hold the LIP or DOWN pad and the time
of day will change 10 minutes at a time. To change
the time by single minutes, give the pads short taps°
3. Press the CLOCK pad to start the clock.
To Set the Timer
1. Press the TIMER ON/OFF pad.
2. Use the UP and DOWN pads to set the timer.
Short taps on the UP or DOWN pad change the
timers setting one minute at a timer Pressing and
continuing to hold the UP pad increases the setting
ten minutes at a time°
3. Once you have set your timer, press the TIMER
ON/OFF pad to start timing. As the timer counts
down a signal will indicate when one minute is left.
After this signal, the display will count down in
seconds. When time runs out, a final signal will sound.
Press the TIMER ONIOFF pad to stop the signal
To Display the Clock While
the Timer is Operating
Pressing the CLOCK pad while the timer is operating
wilt not interfere with the timer's operation; the display
MII change to show the clock, but the timer will continue
to count down and will still signal when time is up.
Press the TIMER ONIOFF pad again to change the
display back to show the timer.
Conventional Clock and Timer
(on some models)
The clock and timer are helpful devices that serve
several purposes.
The Clock
To set the dock, push in the knob
and turn it to the right. Let the
knob out when the clock hands
reach the correct time° Continue
turning the knob to OFE
Timer
The timer has been combined with the range clock.
Use it to time al! your precise cooking operations.
You'll recognize the timer as the pointer that is
different in color than the clock hands. Minutes are
marked up to 30, and hours are marked up to 4 on the
center ring of the clock.
To set the timer, turn the knob to the left--without
pushing in--until the pointer reaches the number of
minutes or hours you want to time.
At the end of the set time, a buzzer sounds to tell
you time is up. Turn the knob--without pushing
in--until the pointer reaches OFF and the buzzer stops.
To Change or Cancel theTimer Setting
When the timer is counting down, use the UP and
DOWN pads to change the remaining time, or press
the TIMER ON/OFF pad to stop the timer. The timer
cannot be cancelled unless you have fully completed
"set timer" instructions above.
12
UsingYour Oven
Before UsingYour Oven
Be sure you understand how to set the control
properly. Practice removing and replacing the shelves
while the oven is cool Read the information and tips
on the following pages. Keep this manual handy where
you can refer to it, especially during the first weeks of
using your new range.
Lighting Instructions for
Standing Pilot Models
Some models have standing oven pilots that must be
lit initially_
To fight the oven pilot:
1. Be sure the OVEN CONTROL knob is in the OFF
position.
2. Open the broiler drawer and remove the broiler pan
and grid. This will malce it easier for you to reach
inside the broiler compartment.
3. Find the oven pilot port at _,
the back of the broiler I )
compartment. The long
robe, running from front /"
to back, is the oven
burner. The pilot port is \
at the back, about one '_
inch below the burner.
4. Using a long match or
match holder, reach in
and light the oven pilot.
• To fight the oven burner, turn the OVEN
CONTROL lmob to the desired temperature° The
burner should light within 60 seconds°
• Proper flame configuration: While using the oven
burner, visually check the burner flame in the broiler
compartment° If flame does not burn as described in
the Installation section of this manual, adjust the
flame following the directions on those pages_
• Power failure: An electrical power failure will not
affect a lighted standing oven pilot°
Lighting Instructions for
Electric Ignition Models
The oven burner is righted by electric ignition (on
some models).
To right the burner, turn the OVEN CONTROL
knob to the desired temperature. The burner should
ignite within 30-90 seconds.
After the oven reaches the selected temperature, the
oven burner cycles--off completely, then on with a full
flame--to keep the oven temperature controlled.
Power Outage
CAUTION: Do not make any attempt to operate
the electric ignition oven during an electrical power
failure° The oven or broiler cannot be lit during a
power failure_ Gas will not flow unless the glow bar
is hot.
If the oven is in use when a power failure occurs,
the oven burner shuts off and cannot be re-lit until
power is restored.
Oven Control
The OVEN CONTROL knob
is located on the control panel
on the front of the range.
Simply turn the knob to the
desired cooldng temperatures°
It will normally take 30-90
seconds before the flame
comes OnoAfter the oven reaches the selected
temperature, the oven burner cycles--off completely,
then on with a fiAl flame--to maintain the selected
temperature.
Oven Light
(on some models)
Use the switch on the control panel to turn the oven
light on and off.
(continued next page)
13
Using Your Oven (ooo oood)
Oven Shelves
The shelves are designed
with stop-locks so, when
placed correctly on the
shelf supports, they will
stop before coming
completely out of the
oven and will not tilt
when you are removing
food from them or
placing food on them.
When placing coolcware on a shelf, pull the shelf out
to the bump on the shelfsupporto Place the cookware
on the shelf, then slide the shelf back into the ovem
This will eliminate reaching into the hot oven.
To remove a shdf from
the oven, pull it toward
you, tilt the front end
upward and pull the
shelf out,
To replace, place the
shelf on tile shelf
support with the stop-locks (curved extension of shelf)
facing up and toward the rear of the oven,. Tilt up the
front and push the shelf toward the back of the oven
until it goes past the bump on the shelf supporto Then
lower the front of the shelf and push it all the way back°
Shelf Positions
The oven has five shelf
supports for baking and
roasting as shown in this
illustration--A (bottom),
B, C, D and E (top). It
also has a special low shelf
position (R) for roasting
extra large items, such as
a large turkey--the shelf
is not designed to slide out at this position. The shelf
positions for cooking are suggested in the Baking and
Roasting sections.
Oven Vents
The oven is vented through duct openings at the rear
of the cooktop. See Features section. Do not block
these openings when cooking in the oven--it is
important that the flow of hot air from the oven and
fresh air to the oven burners be uninterrupted.
• The vent openings and nearby surfaces may
become hot. Do not touch them.
• Do not leave plastic
items on the
cooktop---_ey may
melt ff left too
close to the vent.
Vent appearance and location vary
• Handles of pots and pans on the cooktop may
become hot if left too dose to the vent.
• Metal items will become very hot if they are left
on the cooktop and could cause burns.
• Do not leave any items on the cooktop. The hot
air from the vent may ignite flammable items and
wit1 increase pressure in closed containers, which may
cause them to burst°
Oven Moisture
As your oven heats up, the temperature change of
the air in the oven may cause water droplets to
form on the door glass. These droplets are harmless
and will evaporate as the oven continues to heat up.
14
Loading...