Sears 52725165, 52725155 Owner’s Manual
OWNER'S MANUAL
CHAMPION 8 FT. DROP POCKET POOL TABLE
MODEL NO. P]225LGRL 527.25155
MODEL NO. P]227LGRLA 527.25165
1. READ THIS MANUAL CAREFULLY BEFORE STARTING ASSEMBLY.
Read each step completely before beginning each step.
2. SOME SMALLER PARTSMAY BE SHIPPED INSIDE LARGER PARTS.CHECK INSIDE ALL PARTS
AND CARTONS BEFORE ASSEMBLING OR ORDERING PARTS.
3. USE THE HARDWARE IDENTIFIER TO IDENTIFY AND SORT ALL FASTENERS.CHECK ALL CARTONS
FOR KITS. ALL HARDWARE IS NOT LOCATED IN ONE KIT.
THISTABLEISCONTAINED IN THREESEPARATECONTAINERS:
ESCAI.ADE
S P 0 R T S
PLEASE DO NOT RETURN PRODUCT TO THE STORE!
Contact Escalade® Sports customer service department at:
Phone: 1-866-556-2757 Toll Free !
Fax: 1-866-873-3532 Toll Free !
E-mail: billiardtables@escaladesports.com
Mailing Address (Correspondence Only):
Escalade® Sports, PO Box 889, Evansville, IN 47706
Please visit our World Wide Web site at:
www.escaladesports.com
On-Line Trouble Shooting Frequently Asked Questions
Technical Assistance On-Line Parts Requests
Additional Escalade® Sports Product Information
2L-6860-00
@2004 Escalade Sports
®
Escdade® Spots products may be manufactured and/or licensed underthe following patents.
D446275
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
CAUTION
THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS EXTREMELY FLAMMABLE AND UNDER
PRESSURE! CAREFULLY READ CAUTIONS ON SPRAY ADHESIVE CONTAINER! KEEP OUT OF THE REACH OF
CHILDREN! DO NOT USE OR STORE NEAR HEAT SOURCE ! FLAMES ! SPARKS OR WHEN SMOKING! WORK
AREA MUST BE WELL VENTILATED. OPEN DOORS AND WINDOWS WHEN USING SPRAY ADHESIVE.
t.IMPORTANT t.
THE DRAWINGS IN THIS
MANUAL MAY BE
EXAGGERATED OR MOl-
TO SHOW DETAILS.
Tools Needed: (Not Included)
• Hammer (Claw Type)
• Needle Nose Pliers
• Phillips Screwdriver
• Drill
• 1/8" Drill Bit
• Tape Measure
• Sandpaper (80 grit)
• Sanding Block
• Awl or 8d Nail
• Scissors or Sharp Knife
• Putty Knife
NOTE: Rails are made with cushion rubber at a height that requires standard 2 1/4" diameter balls.
Your dealer has a complete line Billiard Accessories.
NOTE: This table adds weight to any floor. Be sure floor can withstand this kind of weight. If floor sags,
table will be impossible to level.
• Hammer (Small Ball Peen Type)
• Carpenters Levelor 36" Straight Edge
• 7/16" Open End Wrench
• 1/2" Open End Wrench
• Rachet with 3/8", 7/16",
and 1/2" sockets
ASSEMBLE TWO LEG PEDESTALS AS FOLLOWS:
1. Begin by opening hardware kits and sod hardware. Remove the
mounting plate from one leveler #22 and attach it to bottom of
left leg # 19 usingtwo screws #27 and two dowel connectors #26.
Cover holes with adhesive hole covers #28. See Figure t. Screw
leveler #22 back into mounting plate.
2. Repeat for other left leg #19 and two right legs #20.
Covered holes
should face
inward. \
19&20
Use
holes
21
3. Attach leg panels #21 to left leg posts# t 9 and right leg posts#20
using screws #45. Starl by installing the top screws in leg panel
using the pre-drilled statler hole in post #19. Square edge of leg
panel up to edge of post #19 then, install the bottom two screws
#45. (SeeFigure 2) Do not tighten screws#45 until instructed to
do so.
4. Set up pedestals so that they face each other.
Pedestal
15
5. Attach beam # 15 by using four bolts #40, eight washers
#50, and four tocknuts #49 for each of the leg mounting
location. Place one washer between the bolts and beam and
one between leg posts and tocknuts. Tighten these bolts
securely. (See figure 4)
5O
40
WARNING
Holes marked by arrows
MUST be on the TOP
when attached to leg pedestals.
4O
5o
15
6. Attach other beam # 15 to the other side the same way. (See
figure 4)
Make sure the holes in the edge of the beams #15 are on
the top of the beams when attached.
7. Place the frame in its final location. Square
the base frame assembly by measuring
diagonally from the corner of one beam to
the opposite corner of the other beam. (See
Figure 5) Nudgethe frame until both diago-
nals are equal (within 1/16 inch).
8. Go back and tighten all loose screws, nuts
and bolts.
NOTE: Screwheads should be
flush with or below the
top of the slats #16 and #17.
15\
16
Detail A
,8H
36
Slot should
be straight
up and down
Hole for dowel
connector #36
is closer to the
top of beam.
9. Place long slats #16 (50 inches long) and short slats # 17 (36 inches long) across table from beam to beam as shown
in figure 6. Make sure to use the two shorter slats #17 on the ends of the beams and the two longer slats #16 in the center
as shown. Insert four dowel connectors #36 into the four holes in the side of each of the beams # 15, these holes should be
doser to the top of the beams #15. (SeeDetaiIA).AttachthesIats#16, and #17 to the wooden beams #15 by pIacing
screws # 18 through the slats and into the dowel connectors #36 that are inthe beams # 15 and tighten, make sure not to
over tighten them. (See figure 4 and detail A))
HINT: When holes are lined up, the slot in the dowel connector should be vertical. After holes line up, insert screws # 18 into
slats and down into dowel connectors. It is recommended to start the screws by hand and not forcing them with power tools
until you are sure threads are engaged properly. Do not tighten completely yet.
./
10. Square up the long slats # 16 by measuring
diagonally, similar to the method used ear-
Ferto square up base frame. (See Figure 7)
After squaring up slats, tighten all the screws
holding slats #16 and #17tothe beams.
ii ii
" H
q
Loading...