Sears 385.1884180 User Manual

OWNER'S MANUAL

S _A/RS

SEWING MACHINE

MODEL 385. 1884180

SEARS CANADA |NC,

Dear Customer:

You have just invested m a very fine zigzag sewing machme. Before using your new Kenmore machine,
please pause for a moment and carefully read this booklet which contains instructtons on how to operate
and care for your machine.

Specific instructions are given on threading, tension adjustments, cleamng, oiling, etc_ Th_s wilt help you
obtain the best sewing results and avoid unnecessary service expense for conditions beyond our control.

Advice on the operation and care of your machine is always available at your nearest Sears Retail Store,
Please remember, if you have questions about your machine or need parts and service, always mentton

the model number and seria_ number when you inquire.

Kenmore Sewing Machine

Record _n space provided betow the mode_ number and serial
number of this appliance. The model number and serial number

are located on the nomenclature plate, as identified on Page 3 of
th_s booklet,

Model No..385. Serial No,
Retain these numbers for future reference,

THIS MODEL IS A CENTER NEEDLE, LOW BAR SEWING MACHINE.

TABLE

OF CONTENTS

SECTION1.

SECTION 2.

SECTION 3.

KNOW YOUR MACHINE

A Portable Caseor Cabinet _sAvailable ............. 2

Locate and Identify the Parts ................. 2_3

Identify the Accessories ....................... 4

PREPARE YOUR MACHINE FOR SEWING

Set Up the Machine ....................... 5_9

o Plug in the Machine and Switch on the Power ....... 5

u Foot Control Use ..................... 5

• Set the Speed Range Switch ................... 6

• Set the Pressure Dial ....................... 6

• Setting Spool Pins .......................... 7

o Adjust the Presser Foot Lever .................. 7

• Thread Cutter ............................ 7

• Accessory Storage Box ....................... 8

o Free-Arm Sewing: the Removable Extension Table. o 8_9

Know What the Presser Feet Will Do ............ t0_14

e Check Your Presser Foot .................... t0

e Change the Presser Foot .................. t0

o Presser FootTypes ...................... t!_14

Choose Your Needle and Thread ............... 14"15

• Check Your Needle ........................ t4

o Fabric, Needle, Thread and Stitch Length Chart ..... 15

a To Change Your Needle ..................... 15

Prepare the Bobbin ...................... 16_t7

e To Remove the Bobbin from the Machine ......... t6

o Wind the Bobbin ........................ 16

• Insert the Bobbin into the Bobbm Holder ......... 17

Prepare Your Top Thread ................... 18_21

o Thread Your Needle .................. 18

o Pick Up Your Bobbin Thread ................. 19

e Adjust the Top Thread Tension .............. 20_2t

Stitch Selector ............................ 21

Stitch Length ControI ..................... 22

Adjusting Stretch Stitch Balance ................ 22

Stitch Width Contro_ ...................... 23_24

• Three Needle Position .................. 23_24

Reverse Stitch Control ........................ 25

Starting To Sew ............................ 25

LEARN THE STITCHES

Practical Stitch Chart ...................... 26_30

Straight Stitches ........................ 31_33

• Straight Stitch ......................... 31

• Use the Seam Guides ..................... 31

• Turn a Square Corner ..................... 3t

Use the Daring Plate .................... 32

• Topstitching ........................... 32

• Quilting ............................ 33

Darning .............................. 34

Stralght Stretch ........................ 34

Zigzag Stitches ........................... 35_42

o Basic Zigzag ............................. 35

• Satin Stitch ............................ 36

- Applique ............................... 37

• Bar Tacking ........................... 37

• Monogramming ........................ 38

o Embrmdery ............................. 38

• Sew a Button ............................ 39

• Overcasting Stitch ........................ 40

o Rick-Rack Stretch ...... _ ............. 40

• Three-Step Zigzag ........................ 41

• Overcast Stretch Stitching .................. 42

® Serging or Pine Leaf Stretch Stitching ............ 42

Blind Hemming ........................ 43

Lace Work ................................ 44

Buttonhole Making ...................... 45_5t

• Learning to Sew Buttonholes ................. 45

• Built-in System .................... 46_47

o Using Buttonhole Attachment ............... 48_51

Sew in a Zipper ........................... 52_53

Shell Stitching ............................ 54

Two-Point Shell Stitching ...................... 54

Smocking ............................. 55

Stretch Patching ............................ 55

Fagoting Stitch ............................. 56

Herring Bone Stretch ........................ 56

Elastic Stretch Stitch ......................... 57

Box Stitching .............................. 57

Two-point Box Stitch ........................ 58

Overedg_ng Stitch .......................... 58

Decorative Stretch Patterns .................... 59

Decorate w_th Geometric Patterns ................ 60

SECTION 4. PERFORMANCE PROBLEMS CHART

What to Do When ......................... 61_62

SECTION 5.

CAREFORYOUR MACHINE

Replace the Light Bulb ...................... 63

C_ean the Bobbin Holder .................... 63

Clean the Hook Race and Feed Dogs ............. 64

Oiling the Machine ........................ 64

PARTS LIST ................................... 65_66

INDEX ........................................ 67_68

SECTION 1. KNOW YOUR MACHINE

A Portable Case or Cabinet is Available

A full line of sewing cabinets is available at your
nearest Sears retail store or through our general
catalog.
Another option , , buy a Carrying Case : =then
your Kenmore goes anywhere, can be stored any-
where.

Locate and Identify the Parts

Upper Thread Guide

Take-up Lever

Top Thread Tension

Control

Face Cover Plate

Thread Cutter

Needle Plate

Thread Spool Pins

Bobbin Winding Spindle

Stitch Width Control

Spee_ Range Switch

Reverse Stitch Control

Extension Table

{Accessory storage box}

Arm Cover Plate

Hand Wheel

Push-Pull Clutch

Carrying Handle

Presser Foot
Thumb Screw

Presser Foot

Thread Guide

Needle Clamp

Stitch SeSector

Strelch Stitch Adjuster

Light and

Power Swttch

P_ug Connector

Nomenclature Plate

Presser Foot Lever

Free Arm

Snap-on Button

Foot Control

Bobbin

Buttonholeopener

\

Needle set

Lint brush

Darmng plate

Quilter Straight

Zipper foot

Buttonhole gutde

Large st:rew dr_ver

stitch foot

p,a,o/ _'_. _

Blind hem

stitch foot

-%,

Base plat

Smell screw driver

Sliding %
buttonhoSe foot

Overedge foot

Spool pin telt

/

Satin stitch
foot

Buttonhole loot

Buttonh o_e templates

........... J

Plug in the Machine and Switch on the Power

Foot Control Use

Power supply plug

Plug
connector

Machine
plug

NOTE:

t. Check your outlet to be sure it is a 110to 120

2. Insert the machine plug into the three-prong

3. Insert the power supply plug into the outlet.

Before inserting the plug into your
machine, be sure the power switch is

OFF

Volt AC outlet,

outlet, as shown, tt will only fit one way.

Power

/ supply

Sewing ligh_ _

4.

Push the light and power switch to turn
on the power and sewing light,

SAFETY FEATURE:
Your machine witl not operate unless the

llght/power switch _s turned on, If you are
interrupted or stop sewing, turn off the

light/power switch to prevent mllury to
children.

Power sw_Ich

J

.J

The toot control regulates the speed at
which you sew.

To increase speed, gently press down with
the ball of your foot.

To decrease speed, release your foot pres-
sure slightly.

NOTE:

The foot control is sensitive and
will increase or decrease your

sewing speed immediately.
Practice on a scrap of fabric to

regulate your sewing speed to

your taste and needs.

j

Your machine has two ranges of speed--a low range for slower, intricate
work and a high one for faster, general work. On the low setting the machine
will sew no faster than approximately two4hird the speed of the high one,

even when the foot control is fully depressed.

NOTE: It is advisable not to change the speed range switch while

machine is running.

Set the Pressure Dial

Setting
mark

The pressure control dial is located inside the face cover plate,
Set the dial aligning the setting mark on the dial with the groove as follows.

3 ..... most sewing

2 ..... applique and Cut-Out work

1 ..... basting, sewing chiffon, lace, organdy and other lightweight fabrics.

Also for vetours and knits (with more stretch),

NOTE: The pressure dial should be reset at 3 after changing pressure, so

the machine is ready for most normal sewing the next time you use

it.

= Setting Spool Pins

r

_poo_ p,N fe,t_

= Adjust the Presser Foot Lever

= Thread Cutter

The spool pros are used for holding the
spools of thread in order to feed thread to

the machine.
To use, pult up the spool pins, Place _he

spool felt on the pros. Push down for
storage,

The Presser Foot Lever raises and lowers your
presser foot.

You can raise it about 1/4" higher than the normal
up position for easy removal of the presser foot or
to help you place heavy fabrics under the presser

foot_

You don't need a pair of scissors to cut the

thread after you finish sewing. Just use the

handy thread cutter,
The threads are cut the proper length for

starting the next seam,

o AccessoryStorage Box

The lid of the accessory storage box lifts
open toward you.

Sewing accessories are conveniently located
inthe box.

= Free-Arm Sewing: the Removable Extension Table

Your sewing machine can do free arm sewing.

To remove:

To Remove the Extension Table

(for free-arm sewing)

J

1. Grip the table with your index finger and thumb,
as shown.

2. Pull gently toward you.
The ex_nsion table will snap out,

To Attach:

Extension table

This feature makes sewing easy for:

Bar tacking to reinforce pockets, plackets
and waistlines on ready-made or home-

made garments to avoid fabric bunching
around the needle.

• :_,_;_,i!:i_ii_:,_,_i_:_ii_!ii_ii_;i!_i:i_=_ii!_:';_

To Attach the Extension Table

(for flat-bed sewing)

1. Fit the tabs into the slot, as shown.

2. With your thumb and index finger, gently snap in.

* Stitchingsleeves,waistbands,pantlegs,

oranycirculargarmentarea.

* Darningsocksormendingknees,elbows,

orareasofwearinchildren'sclothes.

* Sewingbuttonsonsleeves,waistbands,

etc.

The Presser feet are an important feature of this machine. You need to know
what each foot does in order to use them effectively.

Your presser foot is held in place by a Foot Holder. Each presser foot merely
snaps on the foot holder, which is seldom removed.

If you need to remove or attach the foot holder, here is what you do:

o Changethe Presser Foot
Use the correct presser foot for the stitch you wish to sew. Consult the

Stitch Pattern Chart and the detailed directions for sewing with the various

presser feet,

To Remove:

Foot _ !
holder

SCrew

To Remove:
Turn the screw toward the back of

the machine. Use the large screw
driver,

To Attach:

To Attach:

1. Match

holder with the threaded hole in
the presser bar.

2.

Fit the foot holder screw into
the hole.

3.

Tighten the screw by turning it
toward you.

the hole in the foot

To Snap Off:

To Snap Off the Presser Foot:

1.

Raise the needle bar to _ts hlghest position by turning the hand wheel

toward you.

2.

Raise the presser foot.

3.

Press the snap-on button on the back of the foot holder. The presser
foot will drop off.

10

• PresserFoot Types
Zigzag Foot

f

Straight Feot

To Snap On

G

To Snap On the Presser Foot;

1. Place the presser foot so the hori-
zontal pin on the foot lies just

under the groove of the foot
holder.

2. Lower the presser foot holder to
lock the presser foot in place.

NOTE:

If you do not hear the
presser foot snap in place,
press down on the presser

foot holder firmly until you

hear the snap.

%

A: Zigzag foot

Use this foot for both straight and zigzag

stitching_

Uses: Zigzag stitching {see page 35),

Bar tackir_g (see page 37),
Button sewing (see page 39),

Rick-rack stretch (see page 40_1,
Three-step zigzag (see page 41},
Overcast stretch (see page 42),

Lace work (see page 44),

Two-point shell stitching

(see page 54),

Smocking (see page 55),
Stretch patching {see page 555),

Fagoting (see page 56),
Herring bone stretch tsee page 56),
Elastic stretch (see page 5_7),

Box stitching (see page 57),

Two-point box stitching (see page 58),

Overedging stitch (see page 58),
Decorative stretch stitching
(see page 59).

H: Straight foot

Use this foot exclusively for straight stitching

using center needle position only,

Uses: Straight stitching lsee page 31),

Topstitching {see page 32),
Straight stretch (seepage34),

Quilting (see page 33),

1t

o PresserFoot Types (Continued)

Sliding Buttonhole Foot

Zipper Foot

Satin Stitch Foot

Sliding buttonhole foot

%

Use this foot for buttonholes of buift-ln

system. It is marked to measure your
buttonhofes accurately.

Uses: Buttonhole making {see page 45).

E: Zipper foot

J

This foot can be set to sew on each side of
your zipper. The edges of the foot guide the

zipper and keep the seam straight.
Uses: Zipper application (see page 52).

Use this transparent foot for satin stitch and
outJining applique.

Uses: Satin stitch {see page 36),

Applique {see page 37),
Monogramming (see page 3_88),
Shell stitching (see page 5__44),
Geometric decorative stitching

(see page 60).

F: Satin stitch foot

12

Blind Hem Stitch Foot

Overedge Foot

Qu liter

stitch foot

G; Blind hem

Use this foot for perfect blind hemming.
The foot has ridges on the bottom to keep

the fabric from slipping and a guide screw on

top to guide the folded edge of your hem.
Uses: Blind hemming (see page 43}

C: Overedge foot

This foot is especially constructed for
stitching and/or overcasting seams. The
small brush and Wire guides help control the
fabric, ho_d the raw edge in place and keep it
from puckering, especially when sewing on

knit fabrics.

Uses: Overcasting stitch (see page 40),

Serging tsee page 42)

Quilter

J

This attachment turns your zigzag foot into
a quilting foot.

Uses; Straight stitching {see page 33)

13

= Presser Foot Types (Continued)

Buttonhole Foot

Buttonhole foot

Use this foot when making buttonholes with
buttonhole attachment system.

Uses: Buttonhole making tsee page 48)

Your choice of needle and thread depends on the fabric you are sewing.

tn your needle case, you will find the following color-coded needles:

Btue (t 1) .......... for stretch fabrics

Orange (11 ) ........ for _ightweight fabrics

Red (14) ........... for medium or medium-heavy wetght fabrics

Purple (16) ........ for medium-heavy weight and decorative

topstitching on these fabrics

(This needle has a larger thread hole for

thicker topstitching thread.)

Green (18) ........ for heavy weight fabrics and decorative top-

stitching on these fabNcs

• Check Your Needle

1. Look for barbed or blunt point.

2. A damaged needle can cause permanent snags or runs _n knits, fine silks
and silk-like fabrics.

Always buy a good quality thread. It should resist tangling and be strong.
smooth and consistent in thickness.

14

Fabric, Needte, Thread and :

;titch Length Chart

To Change Your Needle

1

NEEDLE

SIZE AND

COLOR

11.ORANGE

14-RED

14-RED

or

• 16-PURPLE

THREAD SIZE

Polyester CorelCotton

Wrap
Fine Mercerized Cotton

Silk A

50 Mercerized Cotton
Polyester CorelCotton

Wrap

Silk A

50 Mercerized Cotton
Mercerized Heavy-Duty

Polyester Core/Cotton
Wrap

SHk A

Heavy Duty Mercerized

Cotton

Polyester Core/Cotton

Wrap

Silk A

FABRIC

Lightweight:

Batiste, Dimtty, Chiffon,

Silks, Fine Lace° Organza,

Crepe, Tar{eta, Voile,
Organdy

Medium Wetght:

Cotton, Cotton Blends,

Percale_ G ingham_
Shantung, Pique,
Seersucker, Satin. Kmts,

Vinyl Su_tings_ Linen,
Wool Crepe, Leather

Medium Heavy Wmght: l

Corduroy, Detain, Wool,

Sailcloth, Wool Flannel,

Gabardine, Velvets,

Leather

Heavy Weight: 3

Coat rags, Upholstery 18-G R E EN (8 stitches per

Cotton Duck Heavy tnch)

Twitls, Canvas

Decorative top-stitching 16-PURPLE Buttonhole Twist {6-8 stitches
on aH types of fabric 18-GREEN (Use as top thread onSy) per inch)

Stretch Fabrtc: 11 -BLUE

Polyester Double Kmts_ (STRETCH Polyester CoretOotten 2--2.5

Nylon Tricot, Jersey, FABRtC Wrap (1O-12 stitches

Stretch Terry, Spandex, NEEDLE) 50 Mercerized Cotton per inch}

Cire Tricot

RECOMMENDED

STITCH LENGTH

SETTtNG

2

(t2 stitches per

inch]

2--2.5

(1 0.12 stitches

per inch)

2--3

(8-10 stitches

per inch)

3-4

C,

"" "--4 ,/'

Flat

s_de
away

lrom

you

NOTE:

Raise the needle bar to its highest post-

tion by turning the hand wheel toward
you,

1. Loosen the needle clamp screw by turning it
toward you.

2. Remove the needle by pulling it downward.

3. insert the new needle into the needle ciamp
with the fiat side away from you.

4. Push the needle up as far as it will go,

5. Tighten the needle clamp screw firmly with the
large screwdriver from your accessory storage
box.

15

= To Remove the Bobbin from the Machine

1. Gently push down on the bobbin cover plate and slide
=ttowards you.

2. Set aside.

3. Lift out the bobbin, as shown.

= Wind the Bobbin

3lurch

I. Put your spool of thread onto spool pin, with the thread winding in the direction

shown.

2. Pull the clutch away from the machine to stop the needle from moving while you
winding the bobbin,

3. Draw thread from spool through bobbin winder tension disc as shown,

4. Place the threaded bobbin on the bobbin winding spindle so that the thread comes
out on top.

5, Push the bobbin winder spindle to the right until it clicks,

6, Holding onto end of thread, depress the foot control.

7, When the bobbin is slightly filled, stop the machine and cilp the thread coming from

the bobbin.

8. Slowly start the machine again and wind the thread until the bobbin stops.

9. Push the bobbin winder spindle to the left and clip the thread.

10. Remove the bobbin.

11. Push in the clutch for normal sewtng operation.

16

Insertthe Bobbin into the Bobbin Hotder

7

®

1.JPut the bobbin into the bobbin
holder so that the thread feeds

counter-clockwise (left)_

2_

Pull about 4 inches of thread 3.
toward you through the tension
slot @.

Then pull the thread clockwise
toward the back of the machine

through the slot @ .

4. Slide the bobbin cover plate while
pushing it down slightly over the

bobbin, Allow about 4 inches of
thread to show above the needle
plate.

t7

o Thread Your Needle

II I

II l

--I l I

I I I

,,PI,7

The numbered steps above follow the numbers
on the illustrations.

Dotted lines show places where the thread

loops and then is pulled tight.

]

Raise take-up lever to its highest position by turning hand wheel toward you.
Raise presser foot lever.

Place spool on spoot pin as shown, with thread coming from the back of the spool.

1. Draw thread into thread guide using both hands.

2. While holding thread near spool, draw thread down into the tension area and then around the
check spring holder.

3. Firmly draw thread up and through take*up lever from right to left.

4. Draw thread down and slip it through the thread guide,

5. Thread then is slipped into needle bar thread guide.

6, Thread needle from front to back.

NOTE: You may want to cut the end of thread with sharp scissors for easier needle threading.

18

Pick Up Your Bobbin Thread

Raise presser foot lever. Hold
needle thread loosely in left hand
and rotate handwheet toward

you one complete turn,

2. Bring bobbin thread up by pulling
top thread,

3. Pull both threads under and to the

back of the presser foot, leaving 4

to 6 inches of thread clear.

19

m Adjust the Top Thread Tension

Top side of fabric

Top ___

SelUng mark

Choose the Correct Tension:
The best tension will depend on;

the stiffness and thickness of the fabric
the number of fabric layers

--- the type of stitch

thread

Tighlen

For Straight Stitch

The ideal straght stttch witl have threads locked between the two layers of
fabric, as shown above, magnified to show detail.

If you look at the stitch, front and backt you will notice that there are no

gaps, that each stitch is smooth and even.
When adjusting top thread tension, the higher the number, the tighter the top

thread,

The top thread
_s too loose.

The top thread
appears on the

undemde of the

fabric.

Tension _s too loose:
The top thread shows through the

bottom of the fabric. The bottom s_de
of the stitch will feel bumpy.

The top thread

_s1oo tigh_

Top side

o_ Ta

The bobbin lhread
appears on the

upper sudace o_ the
_abrlc.

Tension ts too tight:
"The bobbin thread will come through

the top of the fabric. The top side of
the stitch wi]l fee] bumpy.

20

For Zigzag Stitch

in the correct zigzag stitch, the bobbin threads will not show on the top side
of fabric and the top threads will show slightly on the bottom side. See
below for the correct appearance. To match this appearance, adjust your top

tension.

Top tension Top tension

Too Tight Too Loose

Top s_de of Fabric Top side of Fabric

Bottom sCde of Fabric Bottom side of Fabric Bottom side of Fabric
Too Tight: Too Loop; Just Right:

--Corner ot each --The top thread Minimize the amount
zigzag will pull will loop through of top thread visible on

together on the bottom side ot the bottom side of
top side of fabrics, fabric and will be fabric w_thout causing

pulled almost excessive puckering or
together, eausmg the bobbin

Just Right

Top side of Fabric

thread to show on the
top side. Results vary

with fabric, thread and
sewing conditions,

The stktch selector control determines the stitch you select.
Simply turn this control until the desired stitch is indicated by the red indicator
on the stitch indicator panel. The bottom row of stitches is selected when the
stitch length control is set at the stretch stitch posit'=on.

NOTE: To avoid needle or fabric damage, be sure your needle is up and out of

fabric when selecting a stitch.

Stitch patterns are color-coded to recommend setting zones at the stitch length

control

ZONES

= Orange ........ Straight, Zigzag and Utility Stitches

o Green ......... Geometric Decorative Stitches

= Blue ......... Built-in Buttonhole Making

= Yellow ...... Stretch Stitches

21

Stremh Stitch

V Length

The stitch length controt regulates the length of stitch, and also has a stretch
stitches setting.

The higher the number, the longer the stitch.
0 means no feed.

To select Stretch Stitches, set this control at Stretch Stitch.

NOTE :

When you select decorative stitches (green) or built-in buttonhole

(blue), make sure that you do not set the stitch length control at

"Stretch Stitch".
Study the orange, green, yeIlow and blue section around this

control. These are recommended zones of stitch length and color-
coded to the stitches pictured on the stitch indicator panel.

22

{n stretch stitch sewing, the stretch stitch

adjuster should usually be in a neutral
position (between "+'" and "-" or

position), When sewing some fabrics, you
may need to adjust this controt to

balance the stitches for appearance sake.

If design seems open like the illustrations

to the left, adjust the control slightly

toward "'-" until design looks like the

center design.

If the design appears to be c_osed as in

the right hand illustrations, turn the
conllol toward "'+" until stitching _s as

you desire.

:',Stitch WidthControl

= Three Needle Position
f

V Width

_ 2 3_4 s

f ]

The stitch width control regulates the width
of the stitch you select.

The htgher the number, the wider the stitch.

The stitch width control also regulates the
needle positions for straight stitching.

..... LEFT needle position

(_ ..... CENTER needle position

(_ ..... RIGHT needle position

First select straight stitch by turning the
stitch selector control, then select the
desired needle position by turning the stitch

width control.
You can easily adjust your needle from left

to right without moving your fabric from
under the presser foot.

NOTE: Setting the stitch width control at

0 position also gives you center
needle position.

23

Three Needle Position

_ 3 45

o 1 B

Left Needle Position

Set the dial at left needle position when

sewing the edge of the fabric.

23 45

Right Needle Position

Set the dial at Right needle position

for top stitching when sewing on collar

of jacket etc.

24

To reverse stitch, hold down this con-
trol during sewing.

Release to sew forward again.

Now that you are famillar with the controls on your machine and wlth the accessories provided for the machine,

you are ready to start to sew with your new Kenmore sewing machine. Below are some good habits to follow
each time you sit down to sew:

1. Inspect the needle, tt should be straight, properly set and sharp on the point, It should be the correct size
for the fabric and thread being used. Do not be afraid to change your needle frequently, Many of the new

fabrics made of synthetic blends tend to du!l the needles more easily than fabrics made of natural fibers.

2. Before placing the material on the machine, see that the ends of the threads have been drawn about 4
inches to the rear of the machine, Hold on to threads during the sewing of the first 3 or 4 stitches of the

seam.

J

3. Test the machine stitch on a scrap of fabric you plan to use, The fabric should be double thickness, Adiust
the machine for the length of stitch and tension suitable to your fabric.

4, Fabric should be placed under the presser foot with the bulk of the material to the left of the needle and

the right edge of the material placed on the 5/8" seam marking on the needle plate when making a simple

se_m,

5. Run the machine at a slow even speed. The more pressure you put on the foot contro!, the faster the
machine will sew.

6. Fasten each seam by back tacking at the beginning and end of the seam.

7. Always finish sewing each seam with the needte at its highest point.

8, Guide the fabric gently with your hand in front of the needle. Never pull or hold the fabric in such a way

that the normal feeding is altered,

9. When turning the hand wheel manually, always turn it toward you,

25

I

Stitch Selection Foot and Other Attach. Tension Length Width

STRAIGHT

)

I

l

I

STRAIGHT

STRETCH

Stitch Thread Stitch Stitch

Straight

I
I

_ilter_'?

I
I

Darning Zipper

Plate foot

Straight

II1
III

Needle

Check
Chart

onp. 15

Check
Chart

onp. 1_55

2~6

2_6

Orange

Zone

Yellow

Stretch

Stitch
Position

111
ill

0

or

(3D

0

or

Uses

Regular searms, zippers, topstitching, darning,
etc.

Use on knits and other stretch fabrics, good

for topstitching.

Refer to Page

31 _ 32,
52 ~ 53

34

26

ZIGZAG

RICK-RACK

STRETCH

BLIND HEM

STtTCH

Zigzag

%

Zigza9

Blind hem stitch

Check
Chart

on p. 1__5

Check
Cha_

on p. 15

Check
Che_

on p. 15

3_8

2_6

2_6

Orange

Zone

Yellow

Stretch

Stitch
Position

Orange

Zone

1~6

2~6

2_3

Finish edges, buttons, satin stitch, applique,

monogram, embroidery, sewing bar tacks.

Decorate garments with one row or several.

Use for finishing seams.

35 ~ 39

40

43

Stitch

OVERCAST

STRETCH

Stitch Thread Stitch

Selection Tension Width Refer to Page

Foot and Other Attach. Needle

Zigzag Check

Chart

2_6 3_6 42

<
<

on p_ 15

Stitch

Length

Yellow
Stretch
Stitch

Position

Uses

Use for swimwaar, skipants and other

garments that require stretch.

THREE-STEP

ZIGZAG

SMOCKING

STITCH

SHELL

STITCH

SERGING

Zigzag Check

<

o_

%

Zigzag Cheek

(_ on p. 15

Satin Check

Chart
onp+ t5

Chart

Chart

2_6

2_6

4_9

0.5_ 1

Yellow

Stretch
Stitch

Position

Orange

Zone

5~6

3_6

3~6

Use for finEshing seams.

Use in smocking or as a decorative stitch.

Fimsh hems, sleeve and neck openings.
Use on nylon tricot and other |ingerte to

overcast and seam.

Do shell tucking on blouses and tlnger_e,

41

55

54

onp.

Overedge Blue (11 )

!

%

on p. 15

3_6 Yellow

Stretch
Stitch

Position

3N6

Finish hems, sleeve and neck opemngs. 42
Use on nylon tricot and other lingerie to

overcast and seam.

Do shell tucking on blouses end flngerie.

27

J)

Stitch

BOX

STITCHING

ELASTIC

STRETCH

<

/

FAGOTING

STRETCH

PATCH IN G

Stitch Thread Stitch Stitch

Selection Foot and Other Attach. Tension Length Width Uses Refer to Page

Zigzag

Needle

Check

Chert

3 _ 8 Orange 3 _ 6 Use for overlapping seams. 57

Zone

on p.15

Check
Chart

onp._

Check

Chart

onp.

Check
Chart

onp, 15

3 _ 6 Yellow

3~8 0.5~2

2 _ 6 Ye!tow

Stretch

Stitch

Posltlon

Stretch

Stitch

Position

3-6

5_6

5~6

Use for apply=ng elastic,

Join two folded edges for decorative
open-work appearance.

Use for patchwork quilting,

57

56

55

< <

<

TWO-POINT SHE LL

STITCHING

L> L>

28

Zigzeg

Check
Chart

onp. 15

3-8

Orange
Zone

3-6

Do shell tucking on blouses and llnger=e.

This stitch can also be used as e single

ovedock st=tch as well.

54

Stitch

HERRING BONE

STRETCH

Stitch

Selection

Foot and Other Attach.

Zigzag

%

Needle

Check
Chart

on p. 155

Thread

Tension

2_6

Stitch

Length Width

Yellow

Stretch
Stitch
Positron

Stitch

3~6

Uses

Use as hemming stitch for blankets, tablecloth

and draperies.

Refer to Page

56

TWO-POINT

BOX STITCH

r_

OVEREDGE

STITCH

STRETCH

STITCH

DECORATIVE

DECORATIVE

GEOMETRICS

L

C_
C_

r3

Zigzag

%

Zigzag

%

Zigzag

%

Satin

%

Check

Chart
on p. 15

Check

Chart

onp.155

Check

Chart

onp. 15

Check
Cha_

on p. 15

3~8

3~8

2~6

3-8

Orange
Zone

Orange

Zone

Yellow

Stretch

Stitch

Position

Green
Zone

3~6

3N6

3~6

3~6

Use for overlapping seams.

Use for overedging_

Use m smocking or as a decorative stitch,

Decorate garments with one row or several,

one stitch or a comblnatton.

58

58

59

6O

29

BUTTONHOLE

Foot and Other Attach.

Sliding

buttonhole

Needle

Check

Cha_

on p. 15

Thread Stitch Stitch

Tension Length Width Uses Refer to Page

2 _ 6 3 _ 6 Buttonholes: also corded buttonholes, 46 _ 47

Blue

Zone

17

Q

tl,

SATIN STITCH

D

Buttonhole

Satin

Check
Cha_

on p. 1__55

Check
Chart

on p. 155

2_6

3_8

4

0.5~ 1

2~6

Straight buttonholes end keyhole
buttonholes,

Use for applique work, also as decoratwe

finish for ptacemats, blankets, collars,
cuffs and pockets.

48 _ 51

36

3O

Straight Stitch

Set the Machine

lop thread tension

control 2 to t3

H: Straight foot

NOTE:

Best sewing results are
obtained with the straight
stitch foot, but the zigzag
foot will also provide
acceptable results, and can

be used for all needle
positions.

Stitch width
control 0 or(_D

13 5

Stitch length

control orange

zone

Stretch Stitch

Before sewing with the straight stitch
foot, always set the stitch width
control to 0 or (_ to avoid breaking

the needle.

4.

1. Raise the presser foot.

2. Raise the needle to its highest

position.

3. Place the edge of the fabric next

to a stitching guide line on the

needle plate (5/8" is most

common),

4. Draw the threads toward the back
and lower the presser foot.

5. Press the footcontroI.

6.

Hold the fabric loosely and gently

guide it along the guide line, so
that it feeds naturally,

Do not force the fabric or try to

pull it tight_

7.

At the beginning and end of

seam, you may want to reverse to

lock the stitch.

8,

Raise the presser foot and remove

the fabric.

9.

Cut the threads,

Use the Seam Guides

Cornering guide

The seam guides on the needle plate

are engraved to help you measure seam

width. The lines are 1/8" apart, with
the 5/8" and 7/8" lines marked.

• Turn a Square Corner

guide

To turn a square corner 5/8" from the

fabnc edge:

1. Stop stitching and lower the
needle by turning hand wheel
toward you when the fabric edge

facing you lines up with the
cornering guide, as shown,

2. Raise the presser foot and turn
the fabric to line the edge with

the 5/8" seam guide.

3. Lower the presser foot and begin
stitching in the new direction,

31

Use the Darning Plate

Darning plate

Topstitching

Set the Machine

Stitch width
control 0 grog

2 3 ,_

o 6

Sometimes when you sew, you want to control the fabric yourself.
The Darning Plate covers the feed dogs so that they do not touch the fabric.

To Put on the Darning Plate:

NOTE: The rectangular holes in the Darning Plate match the holes tn the

needte plate. In the darning plate, these holes are slightly to the
right of center.

1. Position the darning plate with the pins on the bottom.

2. Fit the darning plate pins into the needle plate holes at the
5/8" mark. The feed dogs will show through the darning plate
holes.

Use the darning plate in the following ways:

Darning (see page 34),
Button Sewing (see page 39)

lop thread tension

control 2 to 6

Stitch length

control orange

zone

2

Stretch Stitch

H: Strmght foot

The Stitch and Its Uses
Topstitching emphasizes the lines of

your garment and keeps seams and

edges fiat and crisp.
Accent suits or blouses with one or

two rows of topstitching around the
outer edges of cuffs, lapels or collars.

Here's How

1. Lower the presser foot.

2. Keep the edge of the fabric next
to the right edge of the presser

fool

3. Evenly guide the fabric along this
edge to produce an even row of

topstitching 5/8" from the edge.

32

Straight Stitches

= Quilting

Set the Machine

Stitch width
contro_ 0 or

I _ Quilter

_'_ holding

£xorew

JW

Top thread tension control orange
control 2 to 6 zone

Stitch length

e

Stretch Stitch

or

H: Straight foot A: Zigzag foot

The Stitch and Its Uses

Quilting is stitching two layers of fabric

together with batting in between to add

dimension and warmth.

Traditionally, quilting has been used for bed

covers, but now it _sused everywhere.
You can use qu[Itlng on entire garments or

parts of garments, such as yokes, pockets,
cuffs and collars. It is also popular for table

fashions. In addition to straight stitch
quilting, you can quilt with decorative
stitches or stitch pattern combinations.

Here's How

To do quilting successfully, follow these simple steps:

1. Loosen the quilter screw on the back of the presser foot as shown.

2. Slide the quilting guide into the opening under the screw to the width
between lines of quilting stitches you desire.

3. Tighten the screw.

4, Sew the first row of stitching.

5. Sew other rows, guiding the quilting guide over the previous row of stitching.

NOTE: When you are quilting large areas, tack the layers together with the

basting stitch. Then quilt from the center out.

An other qu iltlng variation:

Instead of quilting with rows of straight stitches, you can bartack your quilt at
regular intervals.

Set up the machine as if you were going to sew a button (see page 39). Position
you fabric and bartack.

33

"; i ; , __=;_i:i :, _. ! :ii:i::,:_; ;_i i_! _iil ,i _:i,

Top thread

tension
contro_

2to6

No presser

foot

Darning plate

34

Set the Machine

Stitch width

control 0 or C_

Stitch length
control any number
(not necessary to

adjust}

Stretch Stitch

Sat the Machine

Stitch width
control 0 or C_)

! IH I ,

Top thread tension Stitch length

controJ 2 to 6 control yellow

2

Here's How

1.

Put the darning plate on the needle plate

(see page 32).

2.

Remove presser foot and foot holder
(see page !_00), stretch fabric between

ernbroidew hoops with hole centered.

3.

Draw the bobbin thread up through the

fabric by holding the top thread and taking

one stitch at the spot where you wish to

start darning.

Lower the presser bar and sew at a slow

speed,

5.

Move the fabric back and forth slowly until

you have covered the darning area.

6.

Turn the fabric hatf turn and sew antother

H: Straight foot

The Stitch and Its Uses
This stitch is the stretch variation of

the straight stitch, especially develop-
ed for knits and stretch fabrics.

This stitch can also be used for
topst_tching on all fabrics.

layer of stitching over the first layer,

NOTE:

If your fabric is thin or badly damaged,
use a separate p_ece of fabric under the
hole to rmnforce it,

7. When you finish darning, remove the darning
plate and replace foot holder and foot.

stretch stitch

poslt_on

Stretch Stitch

Stretch stitching was developed
to be used on stretch fabrics and

knits. It can be used on other

fabrics as well. tt works well on
curved seams and on any

garments that will receive a great

deal of strain (ie. children's
clothes},

The stretch stitch does not
actually stretch as it is being

sewn, but _s stitched in a
forward and back motion

(sometimes called a "reverse-

action" stitch), so that it will
gwe when the fabric stretches

instead of breaking.

: Zigzag Stitches :

Basle Zigzag

Set the Machine

Stitch w_dth

contro_ I to 6

_3

Top thread tension

control 3 to 8

A: Zigzag foot

The Stitch and Its Uses
The zigzag stitch is one of the most

common and most versatile stitches on
your machine, it can be a utility stitch

for sewing buttons, buttonholes, hem-
ming, overcasting, mending and darn-
ing. It can also be used to decorate
with trims, appliques and cut-out work

or as a decorative stitch.

Stitch }ength

control Or'e rtge

Zone

Stretch Stitch

Here's How

There are many ways to sew a ztgzag stitch.

4

J

Consult the specific variations for detailed directions.
Satin Stitch page 36,

Applique Work page 37,
Bar Tacking page 37,
Monogramming page 38,
Embroidery page 38,
Button Sewing page 39,
Overcasting page 40.

35

Satin Stitch

¸:¸

Set the Machine

Stitch width

e €

_controf2tO_l 2 3 4- s

Top thread

teRston (_3

contro_ 3 to 8 Stitch tenglh

F: Satin stitch

foot

Pressuredial: 1 or

The Stitch and Its Uses
The Satin stitch is a versatile and often

used decorative stitch, but _t can a]so
be used to overcast a raw edge (for ex-
ample0 blankets, linens, tablecloths
and napkinsh

The Satin stitch is espematly attracUve
in applique.

control 0.5 to 1

Stretch Stitch

Zigzeg width

Slllch
length :

2

t

Close to 0

Here's How
Once your machine is set up to stitch, you may want to experiment on a fragment

of the fabric you are planning to use. Too tight satin stitch may pucker some light
weight fabrics.

36

Applique

Set the Machine

Stitch width
control 2 to 6

= Bar Tacking

Set the Machine

Stitch wtdth

2

control 2 to 6

1

Top thread tens=on
control 2 to 6

F: Satin sttteh

toot

Pressuredial:2

Stitch length

controt 0.5 to 1

2

Stretch Stitch

Baste ior fuse with iron-on fabric
joiner) apptique pieces on the fabric.

Stitch around the applique making
sure the needte falls along the outer
edge of the applique,

When sewing corners, lower the needle
down into the fabric. Raise the presser

foot and pivot the fabric to the right
or _eft.

Top thread tens=on

J

control 2 to 6

Stitch length

control 0.5 to 1

]

;f

ThL5 stitch is similar to a very short
satin stitch and is used to reinforce
points of strain such as corners or

pockets and straps on lingerie.

Stretch Stitch

Sew 4 to 6 zigzag stitches,

A: Zigzag foot

37

iii

Monogramming

Top thread tension

control 2 to 6

F_ Satin stitch

foot

38

Set the Machine

Stitch width

control 5 to 6

2

I

Stitch length
control 0.5 to

4

0_;_ Herc:'s How

Stretch Stitch 3.

1,

Set the same as satin stitch.

2.

Back the fabric with paper or

{nterfacing.

Draw the letters-on the fabric

with tailor's chalk.

4, Satin stitch, adjusting the stitch

width as necessary to form each

pattern.

5, If using paper, carefully remove it

when you have finished sewing.

= Embroidery

Set the Machine

Stitch width

a 6

Fop thread tension Stitch length control

control 2 to 6 Any number Inot

No presser

foot Stretch Stitch

necessary to adjust)

Here's How

1.

Put the darning plate on the needle
plate (see page 3_22).

2.

Remove foot holder {see page 10),

3,

Adjust the stitch width as desired

(see page 23).

4.

Draw the design on to the fabric
with tailor's chalk.

5.

Stretch the fabric between embrm-
dory hoops-and place under the

needle.

6.

Lower the presser foot lever to

engage the top thread tension.

7.

Holding the top thread in your left
hand, rotate the hand wheel toward
you one complete turn.

Pull the top thread to draw the
bobbin thread through to the surface

of the fabric.

8.

Using a medium speed, stitch along

the marked outline, guiding the
fabric carefully by hand.

Sew a Button

Set the Machine

Stitch w=dth control

0 _

Top thread tension

control 2 to 6 co

Stitch length control
Any number inot

._ necessary;o adjust)

A: Zigzag foot

Darning plate

Stretch Stitch

Use the darning plate for button sewing (see page 32).

1. Match the center of the button holes to the center of the slot on the presser

foot,

2.

Adjust the stitch width so that needle wilt drop in each hole.

3.

Lower the foot to hotd the button in place.
Turn the hand wheel by hand so that needle will enter either hole of the
button.

4. Stitch several times.

To strengthen the shank, cut the
threads leaving a 8" tail, Bring the
needle thread down through the hole

in the button and wind it around the
shank.

Draw the thread to the bottom side
and knot.

39

Set the Machine

Stitch width

control 3 to 6

1

= Rick-Rack Stretch

Set the Machine

Stitch w{dth
controi 2 to 6

2

2

Top thread tension
control 3 to8

_D

Stitch length
control orange

zone

2

Stretch Stitch

C: Overedga foot

The Stitch and Its Uses

ThLs zigzag variation is very useful m
garment construction and in finishing
raw edges of any sewing project.

Helpfut Hints
Start overcasting about 118" inside the

raw corner of your seam, If you start
right at the edge, the fabric witt bunch
up and the st=tches wil! become
tangled.

Top thread tension
control 2 to 6

A: Zigzag toot

(2£)

Stitch length
control yettow

stretch stitch

position

Stretch Stitch

The Stitch and Its Uses
Sew on stretch ?abr=cs in any area that

you might use a zigzag stitch.
Thts stitch can be used as a decorative

top stitch as wetl,

4O

Three-Step Zigzag

Set tha Machine

Stitch width

control 5 to 6

Stitch length

control 0.5 to 'i

Stretch Stitch

A: Zigzag foot

]-he Stitch and its Uses
The three-step zigzag is a combination

zigzag and straight stitch. You may use
the three-step z_gzag ever¥whe_e you

would use the basic zigzag stitch. It

has more strength, elasticity, and _s
flatter than a regular zigzag,

The three-step zigzag stitch is especial-

Iy usefut for:

- mending

-- sewing patches smoothly and
securely,

- repairing straight tears.

- finishing seams,

Seam Finishing (Overcasting)
Piace the fabric under the presser toot

so that the edge will be slightly inside

the r_ght hand side of the presser foot,
Gu=de the work so the right hand

stitches fail at the edge of the fabric.

Mending
Pos_t_on the tear under the neec_le so

that the stitching witl catch both sides_

41

Overcast Stretch Stitching

Set the Machine

Stitch width
control 3 to 6

s 3

Sargingor Pine Leaf Stretch Stitchin[

Sat the Machine

Stitch width

control 3 to 6

2

1

Top thread tension

controt 2 to 6

Stitch length
control yellow
stretch stitch

position

2

Stretch Stitch

A: Zi£rzegfoot

The Stitch and Its Uses
This stttch can be used for sewtng a

seam wtth an overcast finish.
The seam ts formed and finished In
one operation. It can be used when
you are making swimwear, ski pants
and other garments that require

stretch.

Here's How

Place the raw edge of the fabric to
the LEFT. of the needle as shown.

Stitch so the needle pierces the fabric
lust short of the outside edge.

Or, place your fabric to allow a 5/8"
seam, then trim seam allowance
after,

Raw or worn edges of older garments
cat_ be overcast to prevent further

raveling,
NOTE: Use a blue stretch fabric

needle, which effectively
prevents skipped stitches.

Top thread tension
contro_ 3 to 6

c_b

Stitch length

control yellow
stretch st=tch

pos_t_on

Stretch Stitch

C: Overed£a foot

The Stitch and Its Uses

Use th_s stttch when you want a
narrow seam that you do not need to
press open flat. It _s ideal for 1/4"

seams on kmts or on medium to
heavywewght woven fabrics where you

want a narrow seam. It _s also great
for making elastic swim wear.

Here's How
Place the fabric under the presser

foot so that the stitches are made
over the edge.

NOTE :

When using stretch kmt
fabric, use a blue stretch
fabric needle whzoh

effectively prevents
skipped stitches.

42

Fop thread tension

control 2 to 6

Blind Hem

Stitch Foot G

Set the Machine

Stitch width
control 2 to :3

0 _

Stitch length
control orange

zone

Stretch Stitch

2 3 #

2

I/4"

Light '_L,JWhen the

Weight _,I needle

Fabric t/4" ,'_

,_ comes

_; to the

Heavy

Weight

Fabric

1. Finish the raw edge of your hem any way you desire. (See overcasting page 40).

2. Measure, turn up your hem and pin,
NOTE: For light weight fabrics, you may need a double fold.

3. Fold the material (bottom side out) on the edge to be stitched, as shown, leaving 1/4" of the finished hem edge
showing.

4. Place garment under presser foot in such a manner that straight stitches wilt be sewn on extended edge. The zigzag

stitch should just catch the fold of the garment.

5. After hemming, press both sides of the finished hem. The top side of the garment will show only the blind stitches.

43

Set the Machine

Stitch width

control 2 to 3

1 Z 3 4- 5

ilili!!ii!iiilji

Fop thread tension

controt 2 to 6

A: Zigzag foot

c_

Stitch _ength
control !

2

Stretch Stitch

Lace adds a fanciful, feminine touch

to blouses and _ingerie. Table linens

and pillows become more elegant

J

wh_,m trimmed w_th _ace.
Turn raw edge of fabric under at least

5/8", Place lace underneath and top-
stitch using stretch blind hem stitch.

Tnm excess fabric close to stitching,

44

= Learningto Sew Buttonholes

With your Kenmore sewing machine you have two methods of making
buttonholes. You may use the built-in system or you may use the
snap-in automatic buttonhole attachment system,

Choose the buttonhole style

1. Built-in bottonholes (rectangular).
Choose this st'_le for waistband, cuffs, belt slots or where you w_ll
need only one or two buttons.

2. Round end buttonholes (Template No. 213504005, 213505006_,
Choose this style for series of buttonholes on dresses, blouses,

vests, jacke_s or coats.

Keyhole buttonholes (Template No. 213506007),
Choose this style for tailored vests, iackets, coats or any time you

need more room for button shank.

Tips on buttonholing

Always make a practice buttonhole on a scrap of fabric you plan to

use. Try the buttonhole with the button you will use,

Always use an interfacing in area of garment where buttonholes are
placed.

Tissue paper or regular interfacing can be used. Tear paper away after
stitching, if it is used..
For heavier weight fabrics, loosen y'our top thread tension slightly.

45

Set the Machine

r _ "_ control 3 to 6

Stitch w_dth

_31 controt

top thread tension

controt 2 to 6

__ Stretch Stitch

Ad usting the Stitch Density

Depending upon your fabric or your
own preference in buttonholes, you

may alter the buttonhole stitch

density withm the blue buttonhole

range on the stitch length dial.
t. For less density, turn the diat

toward "" 1"

2. For more dens=ty, turn the dial
toward "0",

NOTE; Always make a practsce but-

tonhole on a scrap tabric you
plan to use to find the more

46

suitable stitch length.

Stitch length
Blue zone F==_

Stiding buttonhole foot

1, a. Carefully mark the buttonhole

length on your garment.

b, Change to the sliding buttonhole

foot,

c. _nser_ the garment under the

foot with the buttonhole mark-
ing runnmg toward you.

_._s

Slrelch Stitch

2. a. Move the slider (A) toward you
so that the top mark (C) on the

slider meets the start mark {B).

b. Lme up the markings on the

foot with the top mark on your
garment,

c. Lower the presser loot.

NOTE. The markings on the slider

are engraved in centimeters.

3, a, Set the stttch selector at _ ,

b. Sew forward undl you reach the

front markmg of your button-
holm

c. Stop sewmg at the left stitch,

4. a. Set the stitch selector at I_!

m

b. Sew 4 to 6 stitches.

c. Stop sewing at the right stitch.

NOTE:

When sewing at the edge of fabric, set
sliding buttonhole foot as illustrated

[1

5° a. Set the stitch selector at I_l

6. a. Set the stitch selector at

b. Sew until you reach the back of

the buttonhole.

c. Stop sewing at the right stitch.

k._ -- ........ j

b. Sew 4 to 6 stitches.
c. Stop sewing at the left stitch.

7.

Remove the fabric and cut the

hole open with the buttonhole
opener in your accessory storage

box.

47

Buttonhole Attachment System

For more varied and accurate buttonholes, you will enjoy using the button-
hole attachment and templates. Know the parts read carefully how to set up
your machine properly. You will need these items for the buttonhole
attachment system.

Guide slot

t

Buttonhole Style and Size

Round End

Buttonhole

Keyhole

Buttonhole

48

Buttonhole guide plate

Base plate

Measuremen t

ark_ng

Catch

0

Buttonhole templates

Buttonhole foot

Template 213504005 213505006 213506007

3/8" t/2" 15/16" 1-1/16" 7/8" 1-1/16 ''

Sizes

5/8" 13/t6" lq/4" !-t/2" 1-1/4" 1-3/8"

NOTE:

!llustrations of buttonhole on template show actual length of

buttonhole to be sewn, You will find the most suitable buttonhole
tength easily by matching the button with the proper illustration

on the template.

Set the Machine

Stitch w_dth

Pins (A) Lever

a _

Top thread tension

control 2 to 6

Stitch length

control 4

2

Stretch Stitch

Buttonhole toot

Helpful Hints

You can obtain best results to use
#60 _ #80 light weight threads as

bobbin thread.

NOTE: It is advisable to use a blue

stretch fabric needle when
sewing knits and synthetic

fabrics.

Tol

thread

Round

Rectangular hole

v

Hook

Base ptate

a. Remove the extension table.
b. Raise the needle to its highest position.

c. Remove the foot holder.

d, Pull bobbin thread out about 3" straight back toward rear of machine.
e. Insert hook of base plate into rectangular hole of needle plate°
f. Pull lever back to align the hook with the rectangular hole.

g. Snap base p_ate down to fit two pins (A) at the back of base plate into

two round holes (B) on needle plate.
Release tever,

4g

2o a.

Buttonh_e guide ptete

!

_,T_-- Template

G_d _

I "_ _ / ""Catch

I. I

Gu de bock "'" _'_ _" _,-.----- Gear

When you have selected the template with the size and style button-
hole you need, slide the template into the guide plate.

b,

Pull catch toward you while slidin!] the template until the button-

hole size you have chosen is at the s_,_tting mark.

C.

insert gear of base pfate into slot of template and fit guide block
into the center of the guide slot.

Setting Mark

'=::: " Base plate

Top
thread

; toot

Gear_._,//Slot

l

\

Bobbin
thread

a, Attach the buttonhole foot.

3,

b. Adjust position of gear so it is aligned with the starting point of

template.
The lever can be used to change gear position.

c. Pul] the bobbin thread up through guide slot by turning the hand wheel

toward you while holding top thread.

d. Place the bobbin and top threads to the left side of guide plate.

Leave 3 to 4 inches of thread.

Starting

point

5O

4. ab

Marked
buttonhole

Cerl[er
marking"

Measurement

markings

Mark your buttonhole position carefully on the garment.

b.

Placing your garment behind the machine, insert it between the guide
plate and the buttonhole foot as shown.

C_

Align marked buttonhole with center marking on buttonhole foot.

d.

Line up your fabric edge with the measurement markings on the guide

plate just in front of the buttonhole foot as shown,

eL

Pierce the fabric with the needle at the beginmng of the buttonhole.

Fabric

a. Lower the buttonhole foot.
b. Start sewing slowly.

c. Allow the machine to do the work by itself.

(Do not try to guide the fabric.)

d. Stop sewing when the needle returns to the position where it begins.

To release the buttonhole base plate, pull the lever toward you and lift the
base plate off the machine.

Adjusting the stitch density
You may alter the closeness of the stitches by turning the stitch length

control from 4 to 3.

fabrics

(_ Fine stitches for figh_

Stitch length

control 4 "_o3

NOTE:

tf you want your buttonhole to be 1/2 inch from the garment edge,

line up the fabric with the 1/2 inch markings each time you start to sew
a buttonhole.

0 _'4 -o-

Stretch Stitch

L

J

51

Fabric Preparation:

Put the top sides of the fabric together
and sew to the end of the zipper

opening. Use the reverse to lock the
stitches.

Sew the zipper opening with stitch

length at "4"' and top thread tension

at °'3",

End

ol opemng

Top stde

of fabric

Top edge of fabric

Set the Machine

Stitch wtdth

control 0 or

2 3 #

Top thread tension

control 2 to 6

Stitch length

controt 2

Stretch Stitch

E: Zipper

toot

To attach the zipper foot:

- To sew on the left side of the zipper,
attach the presser bar to the right pins
on the zipper foot.

1/8")

To Sew:

1.

Reset stitch length at 2 and top
thread tension at 2 to 6.

4

Fold back the left seam allowance
as shown.

2,

Turn under the right seam allow-
ance to form a 1/8" fold.

3.

Place the zipper teeth next to the

1/8" fold and pin in place.

/Zipper _eelh

Zipper tape

4, Attach the presser bar to the right

pins on the zipper foot.

5. Lower the zipper foot on the top
side at the bottom of the zipper

so that the needle pierces the fold
and the zipper tape.

6. Sew through the fold and the
zipper tape to the point where the
slider begins.

7. Lower the needle to hold the
fabric and raise the presser foot.

• To sew on the right side of the zipper,
attach the presser bar to the left pins

on the zipper foot.

8, Openthezipper.
9, Lowerthepresserfootandstitch

therestoftheseam,

10.C_osethe zipper and turn the

fabric top side up.

1, Remove the zipper foot and

attach the presser bar to the left

pins on the zipper foot.

12. Stitch across and below the bot-
tom of the zipper.

13. Turn the corner and continue to
guide the foot along the zipper

teeth, as shown,

Stitch through the fabric and

zipper tape.

14+ Stop about 2" from the top of the

z_pper.

15. Lower the needle into the fabric
and raise the presser foot,

16, Remove the basting stitches and

open the zipper.

17. Lower the foot and stttch the rest
of the seam. Make sure the'fold is

even.

53

:: : ::: : ;; : :: :;;;: : : :;} ; : :. :

Set the Machine

Stitch width
control 3 to 6

2 3

Top thread tension

eontro| 4 to 9

Stitch length

control orange

zone

Stretch Stitch

F: Satin stitch

foot

_ J

The Stitch and Its Uses
The Shell Stitch is formed by sewing a

blind hem over forded fabric. Several
rows of shell stitching are called shell

tucks.
Shell stitching can be used to finish

hems, sleeve and neck openings.

Sheii tucking can be used to create

scalloped tucks on blouses and

lingerie,

Here's How
1, For best effect:

- set the stitch length as you
desire,

-- you may need to tighten the
top thread tension slightly.

- a_low the needle to just
clear the folded edge of the
fabric when it zigzags.

2. If you sew rows of shell stitches,
space the rows 5/8" apart.

You can sew Shell Stitch on knits or
sort silky wovens in any direction.

Set the Machine

Top thread tension
control 3 to 8

A: Zigzag foot

%.....

Stitch width

o e

Stitch Iength
control orange

zone

Stretch Stitch

3,

\

This stitch can also be used
single overlock stitch as well

as a

54

Smocking

Set the Machine

Top thread tenston

:ontro! 2 to 6

A: Zigzag foot

Stitch width

control 3 to 6

2 3

Stitch length

control yeitow
stretch stitch

pOSJl[lOn

Stretch Stitch

With the stitch length at "4", sew
straight stitching lines 3/8'" apart

across the area to be smocked.

Knot the threads along one edge. Pull

the bobbin threads and distribute the

gathers evenly. Secure the threads at

the other end. Sew the decorative
stitch between the gathering stitches.
Pull out the gathering stitches,

NOTE: Loosen the top thread

tension to make gathering
easier.

Set the Machine

Top thread tension

control 2 to 6

A: Zigzag foot

Stitch width

control 5 to 6

2

Stitch length controi

_D

yellow stretch stitch
pos_oon

Stretch Stitch

The Stitch and its Uses
For patching worn

4

knees,

out elbows or

55

Sot the Machine

Stitch width
control 5 to 6

Set the Machine

Stitch width
control 3 to 6

2

Top thread tension

:ontrol 3 to 8

C_

Stitch length

control 0.5 to 2

Stretch Stitch

A: Zigzag foot

The Stitch and Its Uses

Use this stitch to iota two pieces of

fabric to create an open work

appearance and add design interest.

Here's How

1. Fold under each fabric edge 5/8"
and press.

2. Pin the two edges to paper or
tear-away backing I/8" apart,

3. Sew s_owly, guiding the fabric
so the needle catches the folded

edge on each side.

Top thread tansson
control 2 to 6

Stitch length

control yel_aw

stretch stitch
pos_on

Stretch Stitch

A: Zigzag foot

The Stitch and Its Uses
Use as hemming stitch for blankets,

tablecloth and draperies.

........... J

Here's How
Place the fabric top side up, and sew

3/8" from the edge.
Trim close to stitching. The stitch will

prevent raveling.

56

Stitch

Sot the Machine

Top thread tension
control 3 to 6

A: Zigzag toot

St_l;chwidth
control 3 to 6

_OO

Stitch length
control yellow

stretchstitch

position

Stretch Stitch

Choose this stitch to attach elastic to
garments.

1. Mark the elastic into quarters and
match these to the center front,

center back and side seams.

2. Place the middle of the elastic
under the center of the presser

foot and stitch into place, making
sure the elastlc is evenfy distrt*
bu ted,

Sot the Machine

Fop thread tension

control 3 to 8

A: Zigzag toot

Stitch width

contro_ 3 to 6

2

GD

Stitch length

control orange

zone

2

Stretch Stitch

Use this stitch to join heavy weight
interlining,

Overlap two raw edges together and
use this stitch to join them.

57

¸¸

Set rite Machine

Stitch width

z 3 ,_

o e

control 3 to 6

TOp thread tension (3D

control 3 to B

A: Zigzag foot

Stitch length
control to2

Stretch Stitch

i!iii¸!iii:iii¸_i_ii ..........._

Thi,.; stitch is useful for elastic fabrics
to join them together. (see page 577)

Set the Machine

Stitch w_dth

o 6

Top thread tension c_D

controJ 3 to 8

A: Zigzag toot

Stitch length

control l to 3

Stretch Stitch

This stitch can be used for a over-

edging stitch.

58

DecorativeStretchPatterns

Top thread tenslon
controt 2 to 6

Set the Machine

Stitch width
control 3 to 6

Stitch length controt

yellow stretch stitch

positron

The Stitch and Its Uses

Decorative stretch patterns can be used for adding creative and personaiised

touch to the items you sew for your home and family.

You can decorate ehi|dren's clothes, women's blouses, curtains, etc.

A: Zigzag foot

Stretch Stitch

59

Set the Machirt_

Stitchw_dth
control 3 to 6

I

Top thread tension
control 3 to8

F: Satin stitch

foot

The Stitches and The,r Uses
These stitches are pu rely decorative.

You can sew one row or severa[ or vary the stitch width and length for

special effects.

Experiment on a scrap of fabric to see what spemal effects are possible.

co

Stitch length

contro_ green

ZOn_

Stretch Stitch

Here's How

1. Adjust the stitch width and length as
you desire.

2. Practice the stitch on a scrap of fabric.

3. Mark the lines for decoration on the
fabric, using a washable fabric marker.

4. Lower the needle at the starting point.

5. Lower the presser foot.

6. Gentty guide the fabric atong the
maked line.

6O

;:Whatto DO when

PROBLEM PROBABLE CAUSE CORRECTION

Irregular Stitches

Breaking Needle

Bunching of Thread

Puckering

_ncorrect s_ze needle.
Improper threading,

Loose upper thread tension.

Puiling fabric,

Loose presser foot,

Unevenly wound bobbin.
Nicks or burrs at hole of needle plate,

Pulling fabric,
Incorrect size needle,

incorrect setting of needle,
Loose presser foot.

Upper and lower threads not drawn back
under presser foot before starting seam.

Incorrect thread tension.
Using two different s_zes or kinds of thread.

Bent or blunt needle,
Loose presser foot.

Fabric too sheer or too soft,

Choose correct size needle for thread and fabric,

Rethread machine.

Tighten upper thread tension.

Do not pull fabric; guide it gently.
Reset presser foot.

Rewind bobbin,
Replace needie plate, or polish off burrs completely.

Do not putl fabric; guide _t gently.
Choose correct size needle for thread and fabric.
Reset needle.

Reset presser foot.

When starting a seam be sure to draw both threads under and

back of presser foot about 4" and hold untii a few stitches are

formed,

Reset thread tension.
Upper thread and bobbin thread should be same size and kind.

Insert new needle.
Reset presser foot,

Use underlay of tissue paper,

61

PROBLEM PROBABLE CAUSE CORRECTION

incorrect s_ze needle, Choose correct s_ze needle for thread and fabNc.

SMpping Stitches Bent or blunt needle, insert new needle.

Incorrect setting of needle. Reset needle.

Tight upper thread tension, Loosen upper thread tension.

Starting to stEtch too fast.

improper threading.

Breaking Upper Thread

Breaking Bobbin Thread Lint in bobbin holder or hook race, Clean bobbin holder and hook race.

Fabric not Moving Thread knotted under fabrfc, to stitch.

Machine Jamming Knocking Noise

Tight upper thread tension.

Incorrect size needle.

Sharp eye m needle.
Nicks or burrs at hole of needle plate.

Improper bobbin threading. Check bobbin threading.

Darning plate In place. Adjust Stitch Length Control.
Stitch Length set at 0. Place both threads back under presser foot before beginning

Push-pull clutch is disengaged. Push in the clutch.

Thread caught m hook race. Disassemble and clean hook race,

Lint m bobbin holder or hook race, Clean bobbin holder and hook race.

Start to stitch at a medium speed,
Rethread machine.

Loosen upper thread tension.
Choose correct s_ze needle for thread and tabnc.

Insert new needle.
Replace needle plate, or polish off burrs compfetely.

Remove darning plate.

62

Bulb

1. Unplug the machine and open the
face cover.

CAUTION_ The _ight butb will be

HOT, Protect your
fingers when you

handle it,

2. Push the bulb up and turn the

bulb counter-clockwise to remove
it,

3. Put the new bulb in by pushing it

up and turning it clockwise.

To insure that your machrne operates at its best, you need to keep the
essential parts clean at all times.

The bobbin area can attract dust and lint. Your machine can become sluggish
or knock loudly if a thread is caught,

Follow these directfons:
1_ Turn off the power or uoplugthe

machine.

2. Remove the bobbin cover plate bv
firmly pulling it toward you.

3, Remove the bobbin.

4. Brush or vacuum the dust and lint
out of the bobbin holder,

5. Replace the bobbin.

6, Slide on the bobbin cover plate by

pushing it into the grooves,

63

Open face cover plate and oil points as shown below at least once a year. On or

two drops of oil is sufficient.

Remove excess oil, otherwise it may stain fabrics,

1. Unplug the machine and remove
the presser foot and needle.

2. Remove the bobbin face cover
plate.

3. Remove the screw on the teft side

of the needle w_th the large screw

driver.

4. Remove the needle plate.

6, Use the lint brush to clean the

feed dogs, hook race and bobbin
holder. Also use a soft, dry

c1oth,

5. Take out the bobbin. Lift up the
bobbin holder and remove _t,

In case machine is not used for an

extended time, oll it before sewing.

Use good quality sewing machine oil.

No other oiling is required

Above points are only area which

require oiling on this machine,

Line up the red marks and place
the bobbin holder so the knob fits

next to the stopper in the hook
race, as shown above.

64

PARTS LIST

! 2

3 4

%

11 12 13 16

17 18 19 20 21 22 23

5 7 8

%

65

J

All parts listed herein may be ordered from any Sears store or service center.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING

INFORMATION:

1. PART NUMBER

2. PART DESCRIPTION

3. MODEL NUMBER

4. NAME OF ITEM

If the parts you need are not stocked locally, your order will be electronically
transmitted to a Sears Repair Parts Distribution Center for expedited
handling.

Ref. No, Description

1

2

3

4

5
6
7

8
9

10
11
12
13
14
15
t6
17

18
t9
2O
21

22

23

Part No.

"2&B868

102403202
813404013

655t

6552
6553

6554
652806003
685502008

825813005

823803006

822804118

820817015

822801001

802422002

*6864

6797
820832005

41669

802424004

6830

*6889

652804001
213502003

213501002
213504005
213505006

213506007
213503004

Bobbin box with 10 bobbins

Spool pin felt

No. 11 Stretch fabric needles (BLU)

No. 1 t Single needles (ORG)
No, 14 Single needles (RED)
No. 16 Single needles (PUR)
No, t8 Single needles (GRN)
Straight foot
Zigzag foot

Sliding buttonhole foot
Zipper foot

Satin stitch foot
Blind hem stitch foot

Overedge foot
Quilter

Needle threader

Light bulb
Large screw driver

Small screw driver

Lint brush
Buttonhole opener

Oil and lint brush

Darning plate

Buttonhole guide plate

Base plate
Template (Round end small)
Template (Round end large)

Template (Keyhole)

Buttonhole foot

66

* These items are not furnished with the machine, but may be ordered per

instructions above+

INDEX

A

Accessory storage box ............ 2, 8

Appliqueing ................... 26, 37

B

Bar tacking ................. 26, 37

Base .......................... 2

Base plate ................ 4, 48, 65_-66

Basic zigzag ......... .......... 26, 35

Blind hemming ............... 26, 43_44

Blind hem stitch foot . . _ 4, 13, 26, 43, 65_66

Bobbin ............. 4, 16_17, 63, 65_66

Bobbin holder ............... t7, 63~64

Bobbin thread .................. 19_20

Bobbin winding ................... 16

Bobbin winding spindle ............. 2, t6

Box stitching ................... 28, 57

Buttonhole ..................... 30, 45

Buttonhole attachment ........ 30, 45, 48

Buttonhole foot ....... 4, 14, 30, 48, 65_66

Buttonhole guide plate ..... 4, 30, 48, 65_66

Buttonhole making ............... 45_51

Buttonhole opener .......... 4, 47, 65_66

Buttonhole template ...... 4, 30, 48, 65_66

Button sewing ................ 26, 39

C

Cabinet ......................... 2

Changing needle ................. 15

Changing presser foot ........... 10_11

Cleaning hook race and feed dogs ....... 64

Cornering guide ................. 3t

D

Darning .................. 26, 32, 34

Darning plate ...... 4, 32, 34, 38_39, 65_66

Decorative geometirc patterns ...... 29, 60

Decorative stretch patterns .......... 29, 59

E

Elastic stretch .............. 28, 57

Embroidery ................. 26, 38

Extension table .................. 2, 8

F

Fabric, needle, thread and stitch

length chart .................. !5

Face cover plate ............. 2, 6, 63_'64

Fagoting ..................... 28, 56

Feed dogs ...................... 64

Foot control ..................... 3, 5

Free arm sewing ............... 6_9

H

Hand wheel ................... 3, t9

Herring bone stretch ............. 29, 56

Hook race ..................... 64

L

Lace work ...................... 44

Large screw driver ............ 4, 65_66

Light and power switch .............. 3, 5

Light bulb ................ 63, 65"_66

Lint brush ................ 4, 63_66

M

Monogramming ............ 26, 3B

N

Needle ............... 14_15, 65_66

Needle clamp ............... 3, 15

Needle plate ................... 2, 17

Needle, thread and fabric chart ......... 15

Needle threading ................ !8_19

O

Oiling ........................ 64

Overcasting stitch ................. 40

Overcasting stretch ............... 27, 42

Overedge stitch .................. 29, 58

Overedge foot ...... 4, 13, 27, 40, 42, 65_66

P

Parts list ..................... 65_66

Performance problems ............. 61_62

Plug connector .................. 3, 5

Portable case ..................... 2

Power switch ................... 3, 5

Practica] stitch chart .............. 26_'30

Pressure control dial ................. 6

Presserfoot .................. 3, 10"-14

Presser foot lever .................. 3, 7

Push-pull clutch ................. 3, 16

Q

Quil_r ............. 4,13,26,33,65_66

R

Reverse stitch control .......... 2, 25, 31

Rick-rack stretch stitching ......... 26, 40

S
Satin stitch foot

, , , 4, 12, 27, 29, 30, 36_38, 54, 60, 65_66

Satin stitching .............. 30, 36

Seam guides ...................... 31

Sergmg ....................... 27, 42

Serging or pine leaf stretch .......... 27, 42

Sewing light ...................... 5

Shell stitching ................. 27, 54

Sliding buttonhole foot

............. 4, 12, 30, 46_47, 66_66

Small screw driver ............. 4, 65_66

Smocking ..................... 27, 55

Snap-on button .................. 3, 10

Speed range switch ................. 2, 6

Spool pin felt ............... 4, 7, 65_66

Spool pins ....................... 2, 7

Stitch length control ............... 2, 22

Stitch selector ................... 3, 21

Stitch width control ............ 2, 23_24

Straight stitching ............. 26, 31_33

Straight stitch foot , ; 4, 11, 26, 31_34, 65_66

Straight stretch stitching ........... 26, 34

Stretch patching ................. 28, 55

Stretch stitch adjuster .............. 3, 22

T

Take-up lever .................... 2, 18

67

Thread cutter ..................... 2, 7

Thread guide ................. 2_3, 18

Three-step zigzag ................ 27, 41

Topstitching ................. 26, 32

Top thread ................... 18_21

Top thread tension .............. 20_2t

Top thread tension control ...... 2, 20"_21

Turning a square corner .............. 31

Two-point box stitching ............ 29, 58

Two-point shell stitching .......... 28, 54

Z

Zigzag foot ........ 11, 26_29, 33, 35, 37,

39_42, 44, 54_59, 6_r_66

Zigzag stitching ............. 26, 35_40

Zigzag overcasting ................ 40

Zipper application , ,. ......... 26, 52_53

Zipper foot ....... 4, t2, 26, 52_53, 65_66

68

SETTINGUPYOURMACHINE

1. You'll find spool pins on the top
cover,

Pull up the spool pins and place the
spool pin felt on the pins.

2 Plug foot control into machine

receptacle_ Then connect cord into
any 1!0 -" t20 volt A.,C wall outlet.

3 Your Kenmore sewing machine has

been thoroughly oiled at the factory_

Be sure to wipe off'the needle plate
area, bed plate and shuttle carefully
before sewing a garment tt is wise to
practice on a scrap of fabric so any
surplus oil is absorbed.

STITCH SELECTOR

Spool pin felt

Spool pin

There are certain types of stitches that are used more often than others in your garment
construction. Because of their frequent use, you will soon realise the convenience offered

to you by this control.
The desired stitch will be obtained by turning the Stitch Selector Dial until the stitch is

indicated by the red line on the indicator panel.

c3 c3 c3 c3 E3 E3 C3 E3 C3 E3 C3C3 O E3 E3 E_ E3 C3 C3 C3[]

I',I st,.c.

tli Selector >

PRACTICAL STITCH CHART

' 2, LENGTH 3, WIDTH 4. TENSION 5. PRESSER

STITCH 1. SELECTOR DIAL ! DIAL [ CONTROL FOOT

STRA 'G H T ...................... ii ---- ORANG El zO N _ ............ O OR _ 2T06 _ l l l H' '

ZIGZAG VVV ORANGE ZONE I TO6 I 3T08 A

i BLIND < " N_,._ ORANGE ZONE 2TO3 / 2TO6 ! G

MENDING *V^'v"%v / 0,5 TO 1 5TO6 i 2TO6 A

_HE'L .... .............--V-X-" ORANGEZ0"EI 3TO0! 4T091 F

BOX _ ORANGE ZONE 3 TO 6 3 TO 8 " A

FAGOT,NG ! _ O.0TO2IOTO0! 3T°° I A

_O-PO,NTSHELLf -V-V"_ ORANGEZONEI3TO0 I 3TO8! A

TWO-POINT BOX / 7U_LIMU T ORANGE ZONE t 3TO6 t 3708 t A

OVE:R EDGE l '_VVV _ ORANGE ZONE ! ' ' "' '3"',,,tO" _ 1 3TO8 1 A

,TRA,GHTSTRETOHt "=----'=--=YELLOWPOS,T,ONt OOR®1 2TO0t H

RICK-RAcK I '/_I_ YEL'LOWPOSITIONI =T'°6 i 2TO'........ / A

SMOCKING ...._ YELLOW PosiT ON'/ 3TO6 t 2TO6 t A

......I_ YELLow POSITION I 3 T06 i 2TO6 1 A

ELASTIC i _ Y E LLOW F'O'S'i"Ti'O N ,TO6 l 3TO6 l ....... A ......

PATCHING _ YELLOW PosiTioN 5T06 2T06 A

....."ERR,NG_ONE......_ YE_LOWPOS,T,O.3TO0 1 2TO0 I A

STR ETCH DECORATIVE YELLOW POSITION 3 T0 6 2 TO 6 1 A

BU_ONHOLE I_ _ I_ _ BLUE'ZONE 3 TO 6 2 TO"6 ....................................

' "B UTTO N HO LE''"" i_l _ 4 2 2 TO6

DECORATIVE GEOMETR ICS GREEN ZONE 3 TO 6 3 TO 8 F

"..SATIN VIII_II_I_II_VII_I_VVV i o.s TO I ...............2 TO 6 3 TO 8 F y

i

FULL 25-YEAR WARRANTY ON SEWING MACHINE HEAD .-=
For 25 years from the date of purchase, Sears will, free of charge, repair defects in material or workmanship which appear

_ in the sewing machine head,

FULL TWO YEAR WARRANTY ON ELECTRICAL EQUIPMENT OF SEWING MACHINE

For two years from the date of purchase, Sears will, free of charge, repair defects in material or workmanship which #
appear in the electrical and electromc equipment of the sewing machine, including motor, wiring, switch and speed control

# and printed circuit boards.

WARRANTY

#

FULL 90-DAY WARRANTY ON ALL PARTS AND MECHANICAL ADJUSTMENTS
For 90 days from the date of purchase, Sears will, free of charge, replace any parts and prowde mechamcal service

necessary for proper operation of the sewing machine, except for normal maintenance.

To obtain warranty service described above, SIMPLY CONTACT THE NEAREST SEARS STORE OR SERVICE CENTER IN

CANADA. This warranty applies only while this product is in use in CANADA.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SEARS CANADA INC., TORONTO, ONT, M5B 2B8 i)

#

SEWING MACHINE

Now that you have purchased your Kenmore Sewing Machine, should a need ever exist for repair parts

or service, simply (:ontact your nearest Sears Serwce Center, Be sure to pertinent facts when you call or

visit.

The model number of your Sewing Machine will be shown on your nomenclature plate on the back of
your Sewing Machi-,e. See page 3 for location.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:

*MODEL NUMBER *NAME OF ITEM *PART DESCRIPTION

If the parts you n_ed are not stocked _ocalty, your order will be electronically transmitted to a Sears
Repair Parts Distribution Center for handling.

SEARS CANADA INC., TORONTO, ONT MSB 2B8

S-385 Printed in Taiwan Part No. 652800122 (_