Sears 113.239201,Craftsman 113.239201,Craftsman 113.239291 Owner's Manual

Sears

MODEL NO,

113.239201

SHAPER ONLY

113.239291

SHAPER WITH STEEL

LEGS AND MOTOR

Serial

Number

Model and serial
number may be found

on the front of
the table.

You should record both
model and serial number

in a safe place for
future use.

CAUTION:

Read GENERAL

and ADDITIONAL
SAFETY

iNSTRUCTiONS

carefui|y

WOOD SHAPER

o assembly

+ operating
o repair parts

Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A.

Part No. 72033 Pr',_ed in U S,A

ON CRAFTSMAN WOOD:SHAPER

this Craftsman: Wood Shaper fails duel to a defect in material or

AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE

_her rights which vary from state to state,

Sears Tower. Chicago, IL 60684

general safety

-, :i • : rInstructions fo power tools

1. KNOW YOUR POWER TOOL

Read and understand the owner's manual and labels
affixed to the toot. Learn its application and
limitations as wel! as the specific potential hazards

peculiar to this too!,

2. GROUND ALL TOOLS

This tool is equipped w_th an approved 3-conductor
Cord and a 3-prong grounding type plug to fit the

proper grounding type receptacle. The green conductor

in the cord is the grounding wire. Never connect the

green wire to a live terminal.

3. KEEP GUARDS tN PLACE

in working order, and in proper adjustment and
alignment,

4, REMOVE ADJUSTING KEYS

AND WRENCHES

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

5. KEEP WORK AREA CLEAN

Cluttered areas and benches inwte accidents. Floor
must notbe slippery due to wax or sawdust.

6.:AVOID DANGEROUS ENVIRONMENT

Don't-use power:tools in damp or wet locations or

expose them tO Cain. Keepw0(k' area we lighted.

Provide adequate surrounding work space.

7, KEEP CHtLDREN AWAY

All vis=tors sho_J|d be kept-a safedistance from work

area.

8. MAKE WORKSHOP KID-PROOF

with padlocks, master switches, or by removing

starter keys.

9. DON'T FORCE TOOL

It will do the job better and safer at the rate for which

tt was desMgned

10. USE RIGHT TOOL

Don't force tool or attachmem to do a job _t was not

designed for.

11. WEAR PROPER APPAREL

DO not wear loose clothing, gloves, neckties or jewelry
(rings, wrist watches) to get caught in moving parts.

Nonsfip footwear is recommended. Wear protective
hair covering to contain long hair. Roll long sleeves

above the el bow.

12. USE SAFETY GOGGLES (Head Protection)

Wear Safety goggles (must comply with ANSi Z87.1)

-at all times.: Everyday eyeglasses 0nly have impact
resistant _lenSes,;they: are NOT-safety glasses.,Also, use

face or dust mask if cutting operation is dusty, and ear

protectors (plugs or muffs) during extended periods of
operation,

13. SECURE WORK

Use clamps or a vise to hold work when practical, It's
safer than using your hand, frees both hands to operate

tool

14. DON'T OVERREACH

Keep proper footing and balance at all times.

15.

MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and

changing accessories.

16. DISCONNECT TOOLS

before servicing; when changing accessories such as
blades, bits, cutters, etc.

17. AVOID ACCIDENTAL STARTING

Make sure switch is in "OFF" position before plugging

in,

18. USE RECOMMENDED ACCESSORIES

Consult the owner's manual for recommended

_accessories, Follow the instructions that accompany

i::,!!:i:i;_:!:,i:::!::tfi_:'accessories. The use of improper accessories mav

hazards,

STAND ON TOOL

.... Serious injury could occur if the tool is tipped or if the

: cutting tool is accidentally contacted.

Do not store materials above or near the toot such that
it _snecessary to stand on the tool to reach them.

20. CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part that

is damaged should be carefully checked to ensure that it
will operate properly and perform _ts intended function.

Check for alignment of moving parts, binding of mowng
parts, breakage of parts, mounting, and any other
conditions that may .affect its operation. A guard or
other part that is damaged should be properly repaired
or replaced.

21. DIRECTION OF FEED

Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only,

22. NEVER LEAVE TOOL RUNNING
UNATTENDED

Turn power off. Don't leave tool until it comes to a
complete stop.

:ilADDITIONAL SAFETY INSTRUCTIONS

FOR WOOD SHAPER

CAUTION: Turn motor switch "OFF" and disconnect 18, DO NOT perform layout, assembly, or set-Up work on
Power Cord when changing Shaper cutters or making
adjustments.

Safety is a combination of operator common sense and
alertness at all times when the Wood Shaper is being used,

WARNING: FOR YOUR OWN SAFETY, DO NOT

ATTEMPT TO OPERATE YOUR WOOD SHAPER UNTIL
IT IS COMPLETLY ASSEMBLED AND INSTALLED
ACCORDING TO THE INSTRUCTIONS.,. AND UNTIL

YOU HAVE READ AND UNDERSTAND THE
FOLLOWING:

PAGE

1. General Safety Instructions for Power Tools ..... 2

2, Getting to Know your Wood Shaper ............ 11

3. Basic Wood Shaper Operation ................. t4

4. Maintenance .............................. t8

5. Stability of Machine
The Shaper must be bolted securely to a stand or work

bench, in addition, if there is any tendency for the

Shaper to tip over or move during certain operations, it
should be bolted to the floor.

6, Location

The Shaper should be positioned so neither the
operator nor a casual observer is forced to stand in line
with the workpiece when straight line shaping. This

Shaper is intended for indoor use only.

7. Protection: Eyes, Hands, Face, Ears, Body
Wear safety goggles that comply with ANSI Z87.1

1968. Wear ear plugs or muffs during extended periods

of operation, Do not wear gloves .., roll long sleeves
above the elbow,

8, Always feed against rotation of the cutter. NEVER

"back up" the workpiece.

9. Do not take deep cuts or feed the stock too rapidly.

10. Be particularly careful in shaping wood that contains
cross grains or knots, as these may cause the hands to

be thrown into the cutter or cause kickbacks.

11. Before applying power, make sure the keyed washer is
installed immediately under the spindle nut and the

spindle nut is securely fastened, and all guards are in the

proper position, Make sure cutters are sharp,

12. Avoid awkward hand positions, where a sudden slip

could cause a hand to move into the cutt:er. Never reach

in back of or around the cutter with either hand to hold

down the workpiece.

13. Accumulations of stock or of finished work should not
be allowed on the table. Never clear table while cutter is

rotating.

14. Rubbish, shavings, stock, or other objects or material

should not be allowed on the floor where they may be a

tripping hazard.

15. Use working forms, patterns or holders wherever
possible, and keep them maintained, Care should be
taken that the work is securely fastened in these
fixtures, Stock is often of such size or shape that it
must be clamped in a holder before being shaped, The

inside jaws which clamp directly against the stock

should be lined with sand paper, Guards may also be

:mounted on a holder to afford additional protection.

16: When the fence is used, make sure it Ts securely fastened

and will not slip, and is properly adjusted.

17, Do not wear gloves, neckties, loose sleeves, or ragged or

torn clothing of any kind. Wear safety goggles

complying with ANSI Z87,1-t968 to protect your eyes

from dust or flying particles.

the table while the cutting tool is rotating.

19. NEVER perform freehand shaping - Use either the
fence, or a starting pin in the table and a collar on the

spindle, or a pattern.

20. Do not place your fingers or hands near edge of
material being cut.

21. NEVER perform irregular shaping operations with the
cutter guard removed. Be positive it is installed and
adjusted per instructions.

22. NEVER perform internal shaping operations on this
Shaper.

23. Do not use your hands to remove objects or materials
from around cutters; use a brush.

24. Do not tamper with guards nor make them inoperative
in any way.

25. ALWAYS joint or plane edge on surface of workpiece
that will be in contact with fence and/or table.

26. NEVER attempt to shape warped or twisted or bowed
work pieces.

27. Before leaving the machine, make sure the motor switch
is "OFF" the power cord is disconnected from the

power source, and the cutter has stopped revolving.

28. Never operate the Shaper without a protective cover on
the ur_used shaft end of a double ended motor.

29. If any part of this Shaper should break, bend, or fail in
any way or any electrical component fail to perform

properly, or if any is missing, shut off power switch,
remove power supply cord from power supply and
replace damaged missing and/or failed parts before

resuming operation.

WARNING: DO NOT ALLOW FAMILIARITY (GAINED

FROM FREQUENT USE OF YOUR WOOD SHAPER)TO

BECOME COMMONPLACE, ALWAYS REMEMBER

THAT A CARELESS FRACTION OF A SECOND IS
SUFFICIENT TO INFLICT SEVERE INJURY.

30. Note and follow Safety Instructions that appears on the
Shape:r fence.

WAR NIN G

A KEYED WASHER MUST ALWAYS

BE USED UNDER THE SPINDLE NUT

31. Note and follow Safety Instructions that appear on the
Shaper Switch assembly.

DANGER

FOR YOUR OWN SAFETY:

_EAO AND UNDERSTANO OWN£R S

MANUAL BEFORE OPERATING MACH_N£

1 W£AR S_FET¥ GOGGLES PStq AN$!2'87 t

AT ALL TIME&t

2 BE POStTIVE KEYED _,_,q-_,_._ _S DER_CTLY

LINDE_ gPIN_LE NU? A_ SPJNDL£" NLET IS

TtGHT _E_OR_. T'ORNtN{_ S_4*_.P_R "ON

3 ALWAYS cEED WO_KPIEC£ AGA!N_T

ROTATION OF CUTTER MOTOR AND

CUTTER _OTATE tN SAME QIRECTIO_

4 AVOId" AWK_A_ F,[_._ _OSJ'TIONS

5 _EEP F_NGE_S AWAY _ROM REVOLVING

C{JTTER _ US_ FI×TURE_ WHEN
N_CESSA_tY

6 tJSE OVERHEAD GUARD WH_4 ADJUS1-

ABL_. F_NC£ _S NOT JN PLACE

WARNING: THE 4-3/8" FLAT PULLEY AND THE 2"
MOTOR PULLEY FURNISHED, WILL RUN THE
CUTTER APPROXIMATELY 9000 R,P,M. WHEN

USED WITH A 3450 MOTOR, NEVER SUBSTITUTE
THESE PULLEYS TO INCREASE THIS SPEED

BECAUSE IT COULD BE DANGEROUS.

resultin foreign

objectsbeingthrownintothe,eyes;whichcanresultin
ilseve:re:eyedamageiAlWayswearsafetyg0gglescomplying

;i:_i;_hANSI:Z87_1(shoWnOnPackage)beforecommencing

powe_tooloperation.SafetyGogglesare available at Sears

retaiFbr catalog stores.

MOTOR SPECUFRCATIONS AND

ELECTRICAL REQUIREMENTS

TtiiS rnachine is designed to use a 3450 R.P.M. Motor only.
DOnot use any motor that runs faster than 3450 R.P.M. It
is: wired for _peration on 115 volts, 60 Hz., alternating

current; IT MUST NOT BE CONVERTED TO OPERATE
ON 230 VOLTS, EVEN THOUGH SOME OF THE

RECOMMENDED MOTORS ARE DUAL VOLTAGE.

THESE CRAFTSMAN MOTORS HAVE BEEN FOUND TO

BE ACCEPTABLE FOR USE ON THIS TOOL.

HP RPM VOLTS CATALOG NO.

1/2 3450 115 12!6

1/2 3450 115 1218

_:3/4 3450 115 1219

115 1226

1/2, _ 3450 115 1269"

"MOtor has reversing switch

CAUTION: Do notuse blower or washing machi ne motors
or any motor with an automatic reset overload protector as

their use may be hazardous.

CONNECTING TO POWER SOURCE OUTLET

This machine must be grounded While in use to protect the

This power tool is equipped with a 3-conductor cord and

grounding type plug which has a grounding prong, approved

by Underwriters' Laboratories and the Canadian Standards
Association. The ground conductor has a green jacket and is
attached to the toot housing at one end and to the ground

prong in the attachment plug at the other end.
This plug requires a mating 3-conductor grounded type

outlet as shown.

If the outlet you are planning to use for this power tool is
of the two prong type DO NOT REMOVE OR ALTER
THE GROUNDING PRONG IN ANY MANNER. Use an

adapter as shown and always connect the grounding lug to

known ground,
It is recommended that you have a qualified electrician

replace the TWO prong outlet with a properly grounded
THREE prong outlet,

An adapter as shown below is available for connecting plugs

to 2-prong receptacles. The green grounding lug extending

from the adapter must be connected to a permanent ground
such as to a properly grounded outlet box.

GROUNb|NG LUG

Plug power _ord idto a i 15v properly :grounded type outlet ADAPTER .........

sa;_er fUse:o[: ch:cuit breaker. If you:are not: sure that _0Qr S-PRoNG \_ _ t CONNECTED TO A

WARNING: DO NOT PERMIT FINGERS TO TOUCH 2-PRONG

THE TERMINALS OF PLUGS WHEN INSTALLING OR RECEPTACLE

REMOVING THE PLUG TO OR FROM THE OUTLET.

WARNING:: IF NOT PROPERLY GROUNDED THIS

POWER TOOL CAN INCUR THE POTENTIAL HAZARD

OF ELECTRICAL SHOCK. PARTICULARLY WHEN

USED IN DAMP LOCATIONS IN PROXIMITY TO
PLUMBING. IF AN ELECTRICAL SHOCK OCCURS

THERE iS THE POTENTIAL OF A SECONDARY
HAZARD SUCH AS YOUR HANDS CONTACTING THE
CUTTER BLADE.

If power cord is worn or cut, or damaged in any way, have

it replaced immediately.
Your unit is to be used on less than 125 volts and it has a
plttg that looks like this.

3-PRONG

PLUG ,

PROPERLY___ _ _:

RouND oII-Fn Ui

i OUT GROUNDING

_ PRONG

i

NOTE: The adapter illustrated is for useonly if you already
have a properly grounded 2-prong receptacle. Adapter is
not allowed in Canada by the Canadian Electrica! Code,

The use of any extension cord will cause some loss of
power, To keep this to a minimum and to prevent
overheating and motor burn-out, use the table below to

determine the minimum wire stze (A.W.G.) extension cord.

Use only 3 wire extension cords which have 3-prong

grounding type plugs and 3-pote receptacles which accept
the tools plug.

Extension Cord Length

Wire Size AWG

Up to100' . ................................. 14

100' to 200' . .................................. 12

200' to 400' . ................................ 8

CHECK MOTOR ROTATION

WARNING: FOR YOUR OWN SAFETY, MAKE SURE
PLUG IS NOT CONNECTED TO POWER SOURCE
OUTLET WHEN CHANGING MOTOR ROTATION.

The motor must rotate COUNTERCLOCKWISE when
viewed from the shaft end to which you will mount the

pulley. (See page 8) If it does not, change the direction

according to the instructions furnished with the motor.

UNPACKmNG: AND

CONTENTS

WARRANTY ................................

General Safety Instruction for Power Tools .........

Additional Safety Instructions for Wood Shaper .....

Motor Specifications and Electrical Requirements ....

UNPACKING AND CHECKING CONTENTS .......

List of Loose Parts ..........................

ASSEMBLY .................................

Tools Needed ..............................

Installing Elevating Rod and Table Support .......

Mounting Belt Guard and Motor to Motor Mount +.

Checking Motor Rotation .....................

Installing Motor Pulley .......................

Mounting Motor Support Assembly to Shaper .....

Mounting Switch Assembly ...................

CHECKING CONTENTS

Model 113.239291 Wood ShaPer is shipped Complete in
one carton and includes steel legs and motor.
Model 113.239201 Wood Shaper is shipped complete in

one carton but DOES NOT INCLUDE Steel Legs or Motor.

2

2 Separate all parts from packing materials and check each

3 one with the illustration and the list of Loose Parts to make
4 certain all items are accounted for, before discarding any
5 packing material.

5 tf any parts are missing, do not attempt to assemble the

6 Shaper, plug in the power cord or turn the switch on until

6 the missing parts are obtained and are installed correctly.
7 Remove the protective oil that is applied to the table top

7 and edges of the table. Use any ordinary household type
8 grease and spot remover.

8 CAUTION: Never use gasoline, naptha or similar highly

9 volatile solvents.
9 Apply a coat of automobile wax to the table.

Wipe all parts thoroughly with a clean, dry cloth.

WARNING: FOR YOUR OWN SAFETY, NEVER
CONNECT PLUG TO POWER SOURCE OUTLET UNTIL

ALL ASSEMBLY STEPS ARE COMPLETE, AND YOU
HAVE READ AND UNDERSTAND THE SAFETY AND

OPERATIONAL INSTRUCTIONS.

Assembling Steel Legs ....................... 10

Mounting Wood Shaper on Floor Stand ............ 10

Plugging in Motor ........................... 1 1

Installing Shaper Fence + For Straight Edge

Shaping only .............................. 1 t

Installing Shaper Cutter Guard - For Curved

or Irregular Shaping only .................... 11

GETTING TO KNOW YOUR WOOD SHAPER ...... 13

On-Off Switch ............................. !3

Elevating Control Lever ...................... 14

Spindle Lock Knob ......................... 14

Spindle ................................... 14

Spacers .................................... 14

Keyed Washer ............................. 14

Fence Adjusting Knob ....................... 14

Fence Lock Knob .......................... 14

Fence Faces ............................... 14

Cutter Guard .............................. 14

Starting Pin ............................... 14

Removing and Installing Cutter ................ 14

ADJUSTMENTS .............................. 15

Shaper Fence .............................. 1 5

Fence Faces ............................... 1 5

BASIC SHAPING OPERATIONS ................. 16

Use of Cutter Spacers ........................ t 6

Straight Edge Shaping ....................... 1 7

Shaping With Use of Miter Gauge and

Hold+Down Clamp (Optional Accessory) ......... 1 7

Irregular or curved Shaping ................... 18

MAINTENANCE ............................. 20

LUBRICATION .............................. 20

RECOMMENDED ACCESSORIES ................

TROUBLE SHOOTING ........................ 21

REPAIR PARTS .............................. 22

LIST OF LOOSE PARTS

Included with Model No, 113.239201 and 113.239291

Item PartName Qty.

A
B
C

D

E

F
G
H

J

K

L

M

N

0
P
Q
R

S

T

Motor Mount ............................. I

Guard, Pulley ............................. 1

Pulley, Motor ............................. 1

Belt, "'V'" 1/2 x 33 ......................... 1

Support Assembly, R.H ..................... !

Support Assembly,LH ...................... I

Guard,Cutter ............................. +

Hub Assembly,Lock ....................... I

Nut,Lock ............................... I

StudNut ................................ I

Support, Guard ........................... 1

Bracket, Support .......................... 1

Fence Assembly ........................... 1

Plate, Guard .............................. 1

Switch Box Assembly ...................... I

Spindle Assembly .......................... 1

Base .................................... 1

Owners Manua{ ........................... 1

Bag Assembly, Loose Parts (Part No. 72022)

Containing The Following:

Starting Pin ............................. 1

Insert, Table ............................ 1

Wrench ................................ 1

Screw, Hex Hd. 3/8-1B x 1 ................. 2

Washer25164x 1-118x 7164 ............... 2

B01t+ Carriage 5/16-18 x 1-114 .............. 4

Washer 21]64 I.D. x 7 tB 0.D. x lib .......... 4

Screw, W/L0ckwasher 5]16-t8 x 3/4 ......... 3

Washer11/321.D. x1+1116 x1/8 ............ 2

Wrench, Hex "L" 5]32 .................... 1

Wrench, Hex "L" I/4 ..................... 1

Knob .................................. 1

Nut, Hex Jam 3/8-24 ..................... !

Screw, Hex Hd+ 5/16-18 x 1 1/_, .............. 3

Nut, Hex 5/16-18 ........................ 7

L0ckwasher, Int. 5]! B ..................... 3

Hanger,Cable ........................... 1

Screw, He× Hd. 5/_6-18 x 2 ................ 2

Elevating Rod ........................... 1

Washer 21/84 x 3/4 x 1/16 ................. 5

Screw, Soc. Set 5/1E;..l_ x 5/1_ 1

i ii:izzi ¸/:! ! iii ¸¸:,

Induded With ModeiNo;: 113.239291 only

¢

nty.

8 _=.Screw,Truss:Hd_Ii4o20x 5/B: ,,,:.............. 28

c:i:D_"Nut,_RexIJ4_2o...:;.........................2B

....i:Loci(washer; 1/4:External. _.;. :.:,. .... _=.,;L,. 28

......E Cl_anneliSuppb_ti.,. .......... .. ,. _,.., 2

F

Stiffener, i....!_.;...,,,,... .... :.i...; 2

..... G ::-Stiffener; Side ......................... 2

.H Stiffener, End .......................... 2

e;Screw,Pan Hd.Ty, A N8 x 1/2 ............ 4

Nut, HeXHd. 1/2-13 .................... B

L • Foot, Leveling .......................... 4

M Motor ......... ; ...................... 1

:HARDWAREFOR MOUNTING TOOL

_ • Screw,Hex Hd,5/16-18 x 3 3

• Lockwasher,5/lBExterna _!_:.ii_i_i_ 3

oNut, Hex Jarn5/16-18 ................... 3

• Washer,11/32 ID ....................... 3

• These parts contained in Loose Parts Bag No. 72031.

' III

C

B

A

_----L

ASSEMBLY

i

7/16-INCH WRENCH

1I2-1NCH WR ENCH ......

9/16-_ NCH WRENCH

TOOLS NEEDED

SCREWDRIVER (MEDIUM}
SCREWDRIVER (SMALL)

F RAMI NG SQUARE

Coat the spindle assembly with cup grease, being sure to
wipe some of the greaseinto the elevating slot milled in the

spindle assembly.

SLOT

TAPPED HOLE FOR

ELEVATING ROD

SPINDLE PULLEY

6

INSTALLING ELEVATING ROD

AND TABLE SUPPORT

Position table upside down on 2 x 4's on edge for support

and clearance for spindle assembly.

1. Install (3/8-24) jam nut on short threaded end of
elevating rod and screw the rod into the threads in the
side of spindle assembly.

2. Remove spindle lock knob. htsert the spindle assembly

into the table support, position the tong angle of the
elevating rod straight down and tighten jam nut
securely. The angle portion of elevating rod must be

parallel with spindle assembly.

3. Install knob on end of elevating rod.

4. Rotate the set screw into the table support, while
moving the elevating rod back and forth, until the dog
point on end of set screw enters the elevating slot in

spindle assembly. This can be felt as the set screw and
spindle assembly are rotated. Tighten the set screw,

then back it off 1/4 turn. This wilt allow enough

clearance for the spindle assembly slot to slide on
dog-point end of set screw,

5. Check operation of spindle several times, by moving

elevating control lever back and forth in order to make
sure it is not binding, yet slides effectively on the

dog-point end of screw. Readjust set screw slightly, if

requi red, for smooth operation.

Reinstall spindle lock knob.

6.

Position shaper base on table support casting so the

three mounting holes are aligned. Install and tighten the
three 5/16-18 x 3i4dnch hex-head screws with fock

washers.

MOUNTING BELT GUARD AND MOTOR

TO MOTOR MOUNT

1. Place the motor mount on your workbench.

2. Support rear of motor mount with 3/4" stock as
shown.

3. Find four 5/16" x 18 x 1-1/4 carriage bolts, four
5/16-18 hex nuts, and two 2t/64 x 3/4 x 1/16 Flat

Washers. Position hardware as shown.

POSITION MOTOR WITH

.5/8 IN. DIA, SHAFT THiS END

BELT GUARD

MOTOR MOUNT

3/4 IN. STOCK

{ u ::

:::4.;!:::Place:':Belti::G_ard iunde_iMotor (between; Motor Support
' i:iB_a_ket and M0torll Mount )and makd certaln 518' shaft

: :is Centeied in •Bblt Guard hoie. :inStall nuts finger tight,

?i!!

5/8 IN. SHAFT

i1t,

5/t6 IN. HEX NUTS

CHECKING MOTOR ROTATION

The motor must rotate COUNTERCLOCKWISE when
viewed from the PULLEY end.

1. Place the motor on your workbench or on the floor.

2. Stand clear of the motor and plug the cord into a
properly,grounded outlet (see Page 4). Notice the

rotation of the shaft, If it is not turning
COUNTERCLOCKWISE, REMOVE the plug from the

Outlet and change the:irotation of the motor according

tO the instructions furnished with the: motor,

WARNING_ FOR YOUR OWN SAFETY, MAKE SURE

PLUG IS NOT CONNECTEDi:TO POWER SOURCE
OUTLET WHEN CHANGING MOTOR ROTATION.

COU NTERCLOCKW]SE

ROTATION

1.

INSTALLING MOTOR PULLEY

\

Install motor pulley (flat-faced pulley) on motor shah,

with closed end of pulley facing out. Tighten pulley set
screw securely.

5/32 lN.

TSCREWWRENCH

MOTOR PULLEY

\

FLUSH WITH

END OF SHAFT

k• ••/, : • .

.

Using table insert as a spacer, position motor on motor
mount plate to provide a distance of 1/4-inch from
mounting edge of motor mount plate as shown. Tighten

the four motor mount bolts securely and recheck for

correct positioning.

MOTOR MOUNT PLATE

MOTOR

MOTOR PULLEY

(FLAT-FACE)

TABLE iNSERT I/4 INCH

USED AS A SPACER

MOUNTING MOTOR SUPPORT ASSEMBLY
TO SHAPER

t. PLace V-belt on motor pulley and attach motor mount

plate to shaper base with two bolts (3/8-16 x 1-inch)
and washers. Leave bolts finger tight.

2. Roll the belt onto spindle pulley, pull motor mount
plate toward end of base until belt is tight enough to
prevent slipping and tighten the two bolts. Each bolt

should be in approximately the same position in the
base slots.

3. Position elevating rod in approximate mid position and
turn spindle pulley by hand several times to see that the
belt rides in the approximate mid position of motor

pulley. If not, recheck assembly. The belt should
change positions on motor pulley as the lever position is

changed (while the spindte pulley is rotated by hand).

MOTOR MOUNT PLATE

SPINDLE

ELEVATING PULLEY

ROD

BASE

MOTOR

"J,

MOUNTING SWITCH ASSEMBLY

Attach the switch assembly to the underside of the

Shaper table using the two screws and lockwashers
packed with the switch.