Page 1
Save ThisManual _X_
For FutureReference
SEARS
owner's
manuaa
MODEL NO,
113.235220
&
113=235240
COMPOUND MITER SAW
MODEL NO.
113.235110
NON-COMPOUND MITER
SAW
Serial
Number
Model and serial number
may be found on a plate
attached to your saw, at
the side of the Miter Saw
arm.
You should record both
model and serial number in
a safe place for future use_
FOR YOUR
SAFETY:
READ ALL
INSTRUCTIONS
10 iNCH MITERSAW
e assembly
• operating
o repair parts
\ CAREFULLY J
Sears,Roebuck and Co.,Hoffman Estates,IL60179 U.S.A.
Part No. SP5990 Form NOr SP5990
J
Printed in LISA 10/96
Page 2
fir FULL ONE YEAR WARRANTY ON CRAFTSMAN MITER SAW
within.... one year from the date of purchase, this Craftsman Miter Saw fails due to a defect in
material or workmanship, Sears will repair it, free of charge.
Warranty service is available by simply contacting the nearest Sears service center/department
throughout the United States.
This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Sears, Roebuck and Co., D/817 IL 60179
Safety instructions for Miter Saw ...............................................
Safety is a combination of common sense, staying alert
and knowing how your miter saw works Read this
manual to understand this miter saw.
SAFETY SIGNAL WORDS
DANGER: if the safety information is not followed,
someone Wilt be seriously injured or killed.
_4_WARNING: if the safety information is not fof_
lowed, someone Could be seriously injured or kilted
_4_CAUTION: If the safety information is not followed,
someone May be injured_
Before Using The Saw:
WARNING: To avoid mistakes that could cause
serious, permanent injury, do not plug the miter
saw in until the following steps have been satis-
factorily completed°
, Completely assemble and align saw. (See
"Assembly" and "Alignment" sections within)
• Learn the use and function of the trigger switch,
upper and lower blade guards, stop shaft, bevel tock
knob (Model 113235220 & 113_235240 only) and
cover plate stop screw (see "Getting to Know your
Miter Saw" section within)
• Review and understand all safety instructions and
operating procedures in this manual
• Review the maintenance methods for this miter saw
(See "Maintenance" section within)
• Find and Read the following labels on the miter saw:
XkWARNING / ADVERTENCIA
When Installing Or Moving The Miter Saw:
• Before moving the saw, lock the miter, bevel and
power head positions. Unplug the power cord.
• To avoid back injury,get help when you need to lift
the saw
• Never carry the tool by the cord or power head
switch handle Damage to insulation could cause an
electric shock Damage to wire connections could
cause a fire. A carry handle is provided
Avoid Dangerous Environment.
• Use the miter saw in a dry, indoor place protected
from rain
• Keep work area well lighted
• Place the saw so neither the user nor bystanders are
forced to stand in line with the blade Thrown debris
could injure people in its path
To avoid injury from unexpected saw movement:
• Put the miter saw on a firm level surface where there
is plenty of room for handling and properly support-
ing the workpiece.
• Support the miter saw so the table is level and the
saw does not rock.
• Bolt or clamp the miter saw to its support.
• Never Stand On Tool. Serious injury could occur if
the tool tips or you accidentally hit the cutting tool.
Do not store anything above or near the tool where
anyone might stand on the tool to reach them.
To avoid injury or death from electrical shock:
• This Tool Is Double Insulated to give you added
protection. Double insulation does not take the place
or normal safety precautions when operating this
tool. When servicing this double insulated tool, use
only identical parts
. Make sure your fingers do not touch the plug's metal
prongs when plugging or unplugging the miter saw
Page 3
Before Each Use:
Inspect your miter saw.
• Disconnect The Miter Saw to avoid injury from
accidental starting before changing the setup.
changing the blade or adjusting anything
• Compare the direction of rotation arrow on the guard
to the direction arrow on the blade The blade teeth
should always point downward at the front of the
saw
• Tighten the arbor screw
• Tighten the cover plate stop screw,
Check For Damaged Parts, Check for:
• Proper alignment of moving parts,
• Damaged electric cords,
• Binding of moving parts,
• Broken parts,
• Stable mounting,
• Function of arm return spring and lower guard: Push
the arm all the way down, then let it rise up until it
stops by itself Check the lower guard to see if it
closed fully ff it did not, follow the instructions in the
"Trouble Shooting" section
• Other conditions that may affect the way the miter
saw works,
If any part of this miter saw is missing, bent, or broken
in any way, or any electrical parts don't work, turn the
saw off and unplug it, Replace damaged, missing, or
failed parts before using the saw again
Keep Guards In Place, in working order, and in proper
adjustment
Maintain Tools With Care. Keep the miter saw clean
for best and safest performance Follow instructions for
lubricating DON'T put lubricants on the blade while it's
spinning
Remove Adjusting Wrench and return it to proper
storage location on tool
To avoid injury from jams, slips or thrown pieces:
• Use Only Recommended Accessories. (See
"Accessory" section within) Consult this Owner's
manual for recommended accessories Follow the
instructions that come with the accessories. The use
of improper accessories may cause risk of injury to
persons
. Choose the right 10-inch diameter blade for the
material and the type of cutting you plan to do.
• Make sure the blade is sharp, undamaged and prop-
erly aligned With the saw unplugged, push the
power-head all the way down Hand spin the blade
and check for clearance Tilt the power-head to 45
degree bevel and repeat the check
. Make sure the blade and arbor collars are clean
• Make sure the collars' recessed sides are facing the
blade
. Using 1/4 inch allen wrench supplied, make sure the
arbor cap screw is firmly tightened
, Make sure all clamps and locks are tight and there is
no excessive play in any parts
• Keep Work Area Clean Cluttered areas and
benches invite accidents Floor must not be slippery
To avoid burns or other fire damage, never use the saw
near flammable liquids, vapors or gases,
Plan ahead to protect your eyes, hands, face, ears..
Know Your Miter Saw. Read and understand the
owner's manual and labels affixed to the tool Learn its
applications and limitations as well as the specific
potentialhazards peculiar to this tool.
To avoid injury from accidental contact with moving
parts, don't do layout, assembly, or setup work on the
miter saw while any parts are moving
Avoid Accidental Starting. Make sure switch is "OFF"
before plugging miter saw into a power outlet.
Plan your work.
Use The Right Tool. Don't force tool or attachment to
do a job it was not designed to do Use a different too!
for any workpiece that can't be held in a solidly braced,
fixed position
CAUTION: This machine is not designed for
cutting ferrous metals (steel, iron and iron
based metals). Use this miter saw to cut only
wood, wood like products or soft metals like
aluminum. Other material may shatter, bind on
the blade, or create other dangers.
CAUTION: When cutting any metals, sparks or
hot fragments could cause a fire. To avoid this,
disconnect any dust collecting bag or hose
from the miter saw, and remove all traces of
wood dust from inside dust traps in the miter
saw_
Dress For Safety
WEAR YOUR
Any power miter saw can throw foreign objects into the
eyes This can result in permanent eye damage Wear
safety goggles (not glasses) that comply with ANSI
Z87 1 (shown on package) Everyday eyeglasses have
only impact resistant lenses They are not safety glass-
es Safety goggles are available at Sears retain stores
Glasses or goggles not in compliance with ANSI Z87 1
could seriously hurt you when they break
• Do not wear loose clothing, gloves, neckties or jew-
elry (rings, wrist watches) They can get caught and
draw you into moving parts
• Wear nonstip footwear
• Tie back long hair
• Roll long sleeves above the elbow
• Noise levels vary widely To avoid possible hearing
damage, wear ear plugs or muffs when using miter
saw for hours at atime
• For dusty operations, wear a dust mask along with
safety goggles
Page 4
Safety Instructions For Miter Saws (Continued)-
Inspect your workpiece,
. Make sure there are no nails or foreign objects in the
part of the workpiece to be cut
Plan your work to avoid thrown pieces caused -
when the workpiece binds on the blade and is torn
from your hands.
Plan the way you will hold the workpiece from start to
finish:
Avoid awkward operations and hand positions where a
sudden slip could cause fingers or hand to move into
the blade.
Don't Overreach, Keep good footing and balance
Keep your face and body to one side of saw blade, out
of line with a possible throwback
Never cut Freehand:
• Cut only one workpiece at a time
• Brace your workpiece solidly against the fence and
table top so it will not rock or twist during the cut
• Make sure there's no debris between the workpiece
and its supports.
• Make sure no gaps between the workpiece, fence
and table will let the workpiece shift after it is cut in
tWO
Keep the cut off piece free to move sideways after
it's cut off Otherwise it could get wedged against the
blade and could be thrown violently
• Clear everything except the workpiece and related
support devices off the table before turning the miter
saw on
• Secure Work. Use clamps or a vise to help hold the
work when it's practical
Use extra caution with large, very small or awkward
workpieces:
• Use extra supports (tables, saw horses, blocks, etc )
for any workpiece large enough to tip when not held
down to the table top.
• Never use another person as a substitute for a table
extension, or as additional support for a workpiece
that is longer or wider than the basic miter saw table
• Do not use this saw to cut pieces too small to let you
easily hold the work The thumb side of your index
(pointer) finger should not be closer to the blade than
the outside edge of the fence
- When cutting irregularly shaped workpieces, plan
your work so it will not slip and pinch the blade and
be torn from your hands. A piece of molding, for
example, must lie flat or be held by a fixture or jig
that will not let it twist, rock or slip while being cut
• Properly support round material such as dowel rods,
or tubing. They have a tendency to rofl while being
cut, causing the blade to "bite" To avoid this, always
use a fixture designed to properly hold your work-
piece
WARNING: if planning to cut aiuminum or other
non-ferrous metals: Under adverse conditions,
the blade can grab and throw the workpiece
suddenly and unexpectedly. To avoid injury,
follow all applicable safety instructions, as you
normally would, and:
• Use only sawblades specifically recom-
mended for non-ferrous metal cutting.
• Do not cut metal workpieces that must be
hand held. Use auxiliary clamps or other
equipment as needed.
• Cut non-ferrous metals only if you are expe-
rienced or under the supervision of an expe-
rienced person.
Whenever Saw Is Running:
WARNING: Don't allow familiarity (gained from
frequent use of your miter saw) cause a care-
less mistake. A careless fraction of a second is
enough to cause a severe injury.
Before starting your cut, watch the miter saw while it
runs. If it makes an unfamiliar noise or vibrates a lot,
stop immediately. Turn the saw off Unplug the saw Do
not restart until finding and correcting the problem.
Keep Children Away° Keep all visitors a safe distance
from the miter saw. Make sure bystanders are clear of
the miter saw and workpiece
Never confine the piece being cut off Never hold it,
clamp it, touch it, or use length stops against it while the
blade is spinning It must be free to move sideways on
its own. If confined, it could get wedged against the
blade and thrown violently
Let the blade reach full speed before cutting
Don't Force Tool. It will do the job better and safer at
its designed rate Feed the saw into the workpiece only
fast enough to let the blade cut without bogging down
or binding
Before freeing jammed material:
• Turn switch "OFF".
• Unplug the miter saw
• Wait for all moving parts to stop
After finishing a cut:
• Keep holding the power head down.
• Release the switch, and wait for all moving parts to
stop before moving your hands.
• tf blade doesn't stop within 6 seconds, unplug the
saw and follow the instructions in the "Trouble
Shooting" section for fixing the blade brake before
using the saw again.
Before Leaving The Saw:
Never Leave Tool Running Unattended, Turn power
off.,Wait for al! moving parts to stop
Make workshop child.proof Lock the shop, Disconnect
master switches, Store tool away from children and oth-
ers not qualified to use the tool.
Page 5
Glossary of Terms for Woodworking ...............
Arbor Miter Cut
The shaft on which a cutting tool is mounted An angle cutting operation made across the width of the
Bevel Cut workpiece
An angle cutting operation made through the face of the Resin
workpiece A sticky, sap based substance that has hardened.
Compound Cut
A simultaneous bevel and miter cutting operations
Crosscut
A cutting operation made across the width of the work-
piece
Freehand
Performing a cut without using a fence (guide), hold
down or other proper device to prevent the workpiece
from twisting during the cutting operation Twisting of
the workpiece can cause it to be thrown.
Gum
A sticky, sap based residue from wood products
Heel
Misalignment of the blade
Kerf
The amount of material removed by the blade in a
through cut or the slot produced by the blade in a non-
through or partial cut
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in
one minute
Sawblade Path
The area of the workpiece or table top directly in line
with either the travel of the blade or the part of the work-
piece which will be, or has been, cut by the blade
Set
The distance that the tip of the sawblade tooth is bent
(or set) outward from the face of the blade
Workpiece
The item on which the cutting operation is being per-
formed. The surfaces of a workpiece are commonly
referred to as faces, ends, and edges
FACE
EDGE
Motor Specifications and Electrical Requirements
Power Supply and Motor Specifications
The AC motor used in this saw is a universal, nonre-
versible type having the following specifications:
MODEL
113 235110
Maximum Developed H P
Voltage
Amperes
Hertz (Cycles)
Phase
RPM
Shaft Rotation (blade end)
WARNING: To avoid electrical hazards, fire haz-
ards, or damage, or damage to the toot, use prop-
er circuit protection. Your saw is wired at the fac-
tory for 120v operation. Connect to a t20v, 15-
amp branch circuit and use a 15-amp time delay
fuse or circuit breaker. To avoid shock or fire, if
power cord is worn or cut, or damaged in any
way, have it replaced immediately.
120 120
12 15
60 60
Single Single
5000 5200
Clockwise Clockwise
MODEL
113 235220
&
113,235240
3
Double Insulated
The miter saw is double insulated to provide a double
thickness of insulation between you and the tool's elec-
trical system All exposed metal parts are isolated from
the internal metal motor components with protecting
insulation
Your unit has a plug that looks like the one shown
below
To reduce the risk of electrical shock, this appliance has
a polarized plug (one blade is wider than the other) This
plug will fit in a polarized outlet only one way, if the plug
does not fit fully in the outlet, reverse plug If it still does
not fit, contact a qualified electrician to install the proper
outlet, Do not change the plug in any way
WARNING: Double insulation does not take the
place of normal safety precautions when operat-
ing this tool.
Page 6
Motor Specifications and Electrical Requirements (Continued)
DANGER: To avoid electrocution:
1. Use only identical replacement parts when
servicing a tool with double insulation.
Servicing should be performed by a qualified
service technician.
2. Do not use in rain or where floor is wet,
This tool is intended for indoor residential use
only.
Motor Safety Protection
IMPORTANT: To avoid motor damage, this motor
should be blown out or vacuumed frequently to keep
sawdust from interfering with normal motor ventilation.
1 Connect this tool to a 120v, 15-amp branch circuit
with a 15-amp time delay fuse or circuit breaker.
Using the wrong size fuse can damage the motor
2. If the motor won't start, release the trigger switch
immediately UNPLUG THE TOOL, Check the saw
blade to make sure it turns freely, If the blade is free,
try to start the motor again if the motor still does not
start, refer to the "Motor Trouble-Shooting Chart."
3,. If the motor suddenly stalls while cutting wood,
release the trigger switch, unplug the tool, and free
the blade from the wood. The motor may now be
restarted and the cut finished.
4. Fuses may "blow" or circuit breakers may trip fre-
quently if:
a. ,,,,.,,v, is Overloaded-Overloading can occur if
you feed too rapidly or make too many start!stops
in a short time,
b Line voltages are more than 10% above or below
the nameplate voltage For heavy loads, however,
the voltage at motor terminals must equal the volt-
age specified on nameplate
5. Most motor troubles may be traced to loose or incor-
rect connections, overload, low voltage (such as
small size wire in the supply circuit) or to overly tong
supply circuit wire. Always check the connections,
the load and the supply circuit whenever motor
doesn't work well Check wire sizes and length with
the Wire Size Chart below
Wire Sizes
NOTE: Make sure the proper extension cord is used
and is in good condition.
The use of any extension cord will cause some loss of
power, To keep this to a minimum and to prevent over-
heating and motor burn-out, use the table below to
determine the minimum wire size (A W G) extension
cord,
Length of the
Conductor
110-120V
0_25
26-50
Wire Sizes Required for 120v
(American WAreGable Number)
14
12
Table of Contents
Section Page
Warranty ................................................................. 2
Safety Instructions for Miter Saw ............................. 2-4
Glossary of Woodworking Terms ............................... 5
Motor Specifications and
Electrical Requirements ..................................... 5-6
Unpacking and Checking Contents .......................... 7
Tools Needed .................................................. 7
Unpacking ..................................................................... 7
List of Loose Parts ..................................................... 7
Getting to Know Your Miter Saw ................................... 8
Section Page
Assembly .......................................................... 9
Alignment ............................................... 10-11
Mounting the Miter Saw ................................. t 2-13
Safety Instructions for Basic Saw Operations .......14-!6
Basic Saw Operations ............................... 16-21
Maintenance and Lubrication ............................. 22
Sears Recommends the Following Accessories ..... 23
Trouble Shooting Guide ................................. 24-25
Repair Parts .................................................. 26-3t
Page 7
Unpacking and Checking Contents
Tools Needed
Tools required for alignment:
1 Combination Square
2 Combination wrench, !/4" Hex "L" wrench with #2
phillips tip (supplied)
ii u
COMBINATION SQUARE MUST BE TRUE
DRAW LIGHT STRAIGHT EDGE OF
LINE ON BOARD BOARD 3/4" THICK
QUARE
1/2't SOCKET &
SOCKET WRENCH
J
HEX "L" W/PHILLIPS WRENCH (SUPPLIED)
Unpacking
WARNING: To avoid injury from unexpected
starting or electrical shock, do not plug the
power cord into a source of power during
unpacking and assembly. This cord must
remain unplugged whenever you are working
on the saw,
Model 113235220, 113 235240 and 113.235t10 Miter
saws, are each shipped complete in one box
NOTE: This manual gives instructions for both
113 235220 & 113235240 compound miter saw and
113235110 nomcompound miter saw The two saws
are very similar in design and function Many parts are
identical. The illustrations will reflect the compound
miter saw when describing most applications.
Illustrations of the non-compound miter saw wilealso be
given to explain the features that are unique to that
saw
ALONGTH,SEO
SHOULD BE NO GAP OR OVERLAP
WHEN SQUARE IS FLIPPED
OVER IN DOTTED POSITION
to avoid back injury, get help whenever you
I WARNING: Although small, this saw is heavy,
have to lift the saw more than 10 inches.
1 Remove the miter saw from the carton by lifting the
saw by the carry handle.
WARNING: If any part is missing or damaged,
do not plug the saw in until the missing or
damaged part is correctly replaced° To avoid
electric shock, use only identical replacement
parts when servicing double insulated tools.
2 Place the saw on a secure stationary work surface
and look the saw over carefully
List of Loose Parts
A Basic Saw Assembly ..................... 1
B Owners Manual Form ..................... 1
C Dust Elbow ............................ 1
A
Page 8
Getting to Know "YourMiter Saw
1 Warning label
2,, Stop Shaft - The miter saw can be locked in the
MITER SAW
SWITCH HANDLE
lowered position for compact storage.
3 Miter Lock Knob - The miter lock knob securely
locks the miter saw at a desired miter angle Index
points have been provided at O, 22.5 R/L, and 45
R/L I.
4 Miter Index Spring - Loosen Miter Lock Knob and
depress the index spring to move out of 0_22-1/2° &
45 ° indexes
5, Bevel Lock Knob - The bevel lock knob locks the
miter saw at a desired bevel angle. Model
113,,235200 only
6 Bevel Index Pin - This pin allows for quick 0° and 2.
45 ° bevel settings The pin may also be pulled out STOP
far enough to override the stops., Model SHAFT
113.235220 & 113 235240 only.
7, Lower Blade Guard - The btade guard helps pro-
tect your hands from the blade in the raised posi-
tion. To avoid binding on the workpiece, it retracts
as the blade is lowered,
8, Miter Saw Switch Handle - The saw handle con-
tains the trigger switch with a lock-off button The
blade is lowered into the workpiece by pushing
down on the handle, The saw will return to its
upright position when the handle is released.
9 On-Off Trigger Switch - To prevent the trigger BASE
15,
from being accidentally engaged, a lock-off button
is provided To start the toot, push the lock-off but-
ton forward and squeeze the trigger Release the
trigger to stop the miter saw,
10. Padlock Hole - A hole in the switch trigger and
handle has been provided so that a padlock (not
supplied) could be attached to prevent unautho-
rized use,
11, Miter Saw Carry Handle - After locking the power
head in the !owered position with the stop shaft, the
12.
COVER PLATE
STOP SCREW _'_
saw is conveniently carried using this handle,
12 Cover Plate Stop Screw - When this screw is
loosened, the cover plate is rotated to the rear,
allowing for blade removal/replacement.
13. Arbor Lock (Model 113.235220 & 1t&235240
Only) - Allows the user to keep the blade from 7.
rotating while tightening or loosening the arborLOWER BLADE
screw during blade replacement or removal, GUARD
14, Combination Wrench - Used for l/4" hex and
phillips head screw adjustments Storage is provid-
ed as shown,
15, Base - Supports table, holds accessories and
allows for workbench or Iegset mounting,
FENCE
8,,
MODEL t13,235220 &
UPPER BLADE
GUARD
TRIGGER SWITCH 11
BEVEL LOCK KNOB
1t3,235240 ONLY
9_
5.
MITER SAW
CARRY HANDLE
COMBINATION
BEVEL, iNDEX
PIN MODEL 113,235220 &
tl 3,235240 ONLY
LOCK OFF
BUTTON
14.
ELBOW
6
1Q
PADLOCK
HOLE
13
ARBOR LOCK
4.'
MITER INDEX
SPRING
MITER LOCK KNOB
3.
Page 9
Assembly ......................................................................
Removing or Installing the Blade
WARNING: To avoid injury from a thrown work-
piece or thrown pieces of blade, do not use a
blade larger or smaller than 10" diameter.
WARNING: To avoid injury from unexpected
starting, unplug the saw whenever you are
removing or installing the blade.
1. Unplug the saw from the outlet
2 Loosen the cover plate stop screw with phillips end
of the combination wrench, supplied.
3 Lift the lower guard up and tilt the lower guard
assembly back so the arbor screw is exposed.
4a. For Model 113 235220 & 113 235240 only, find the
arbor lock between the upper guard and the miter
saw handle press the arbor lock and hold it in firmly
while turning the arbor screw The arbor lock will
engage within one revolution
4b For either saw model you may lower the blade
down on to a scrap piece of wood positioned
against the fence This will serve as an alternate
locking means
5. Place the 1/4" allen end of combination wrench
supplied into the arbor screw. Remove the arbor
screw, outer blade collar, and the blade
NOTE: Pay attention to pieces removed, noting their
position and direction they face (see illustration)Wipe
the blade collars clean of any sawdust before installing
a new blade
6. Install the new 10" blade (see recommended
accessory list) Make sure the rotation arrow on the
blade matches the clockwise rotation arrow on the
upper guard.
7 InstaLlthe outer blade collar, and arbor screw Turn
the alien wrench counter clockwise to secure the
blade Tighten arbor screw securely,
8. Lower the lower blade guard until the slot in cover
plate rests all the way down on the coverptate stop
screw. Tighten the screw with phillips end of the
combination wrench, supplied.
DANGER: Never use saw without cover plate
securely in place. It keeps the arbor screw from
falling out if it accidentally loosens, and pre-
vents the spinning blade from coming off the
machine.
9 Be sure the arbor lock is released so the blade
turns freely
NOTE: On Model 113235220 & 113235240, the arbor
lock can be damaged by improper use
MITER SAW
HANDLE
COVER PLATE
ARBOR COVER PLATE
SCREW STOP SCREW
ARBOR
LOCK
LEFTHANDTHREAD
BLADE COLLARS
UPPER
BLADE
GUARD
BLADE
"COLLARS
BLADE
:ESSES
WARNING: Make sure the collars are clean and
properly arranged. After installing a new blade,
make sure the blade clears the table slot at the
0° and 45 ° bevel positions. Lower the blade
into the lower table and check for any contact
with the base or turn table structure.
\
ARBOR
SCREW
BLADE
Page 10
Assembly (continued)
Assembling Dust Elbow
1 Locate the dust elbow
2 Unplug power cord.
3 With the miter arm locked in the down position,start
the dust elbow onto the dust nozzle at an angle to
retaining lip. SECOND
4. Firmly press the dust elbow the rest of the way onto RETAINING
the second retaining lip LIP
NOTE: At first time installation, or if assembled ina cool
or cold climate, the rubber is not as flexibleand will be
more difficult to assemble.
Alignment .........
Step One-Checking and Adjusting Blade
Squareness to Fence (Miter Alignment)
WARNING: To avoid injury from unexpected
starting or electrical shock, do not plug the saw
in. The power cord must remain unplugged
whenever you are working on the saw.
1 To check blade squareness to fence, use a combi-
nation square, Place the square against the fence
and next to the blade as illustrated. Place the square
so the set in the teeth won't hold it from the blade
The blade should contact the full length of the
square
2. If blade contacts fult length of square, proceed to
next adjustment, tf blade is not square to the fence,
follow the alignment procedures: a through f.
a Loosen miter lock knob a haft turn. The saw
power head should still be secured in the lowered
positionby the stop shaft_
NOTE: Take the saw off its stand, bench or ply-
wood base if readjustment is necessary.
,, i,i ,,,,i,,
DUST ELBOW
\
MITER INDEX SPRING
CAP HEAD SCREWS
unit, steady the base with one hand while Ioos-
I CAUTION: To keep from losing control of the
ening the two bolts with the other hand.
b With the unit securely resting on a large stable
surface, tilt the unit by lifting up on one side or the
other of the base. Using allen wrench supplied,
loosen the two miter index spring cap head
screws on the underside of the turn table.
Co Return the saw to its normal resting position
Make sure the miter lockknob is loose but do not
release the indexspring.
d. Use the miter saw knob to move the turn table
and saw so that the blade contacts the full length
of the square. Watch out for tooth seL Turn the
miter lock knob clockwise to lock saw square to
fence
e Tilt saw as in Step b and tighten cap head
screws
f Recheck blade squareness to fence and readjust
if necessary.
]
10
Page 11
Alignment (continued),,
Adjustment of Miter Scale Indicator
1 Loosen the phiitips screw that holds the indicator in
place
2 Reposition the indicator and retighten screw
WARNING: To avoid injury from unexpected
starting or electrical shock, do not plug the saw
in, The power cord must remain unplugged
whenever you are working on the saw.
Step Two-Bevel Adjustments
NOTE: Bevel Adjustments are only performed on
model 113 235220 & 113235240. compound miter
saw If you have Model 113235110 saw, proceed to
"Mounting Miter Saw" section
Bevel Stop Adjustments
NOTE: The miter saw was assembled, aligned, and
inspected before shipment, Alignment should be
checked and any adjustments made to insure accurate
cuts
t Check miter lock knob setting The miter lock knob
should be at the 0° position To reset the miter angle,
turn the miter lock knob counter clockwise and press
down the index spring
2 Lower the power head and lock the stop shaft, Make
sure the bevel index pin is pushed in Loosen the
bevel lock knob and tilt powerhead until it contacts
the 45° stop
3 Using the square, check for accuracy of the 45° stop
(when the blade makes contact with the fult length of
the square), Do not measure across the set of a
blade tooth Repeat this for 0° bevel If either stop is
inaccurate, follow the alignment procedures: a
through g
a. Using the allen wrench provided, loosen the
screw which holds the inaccurate bevel index
stop
b Move the power head left or right until btade
makes contact with full length of square
c Tighten bevel lock knob,
d Make sure the index pin is pushed in
e Slide bevel index stop over until it firmly contacts
the index pin
f, Tighten bevel index stop screw
g Recheck indexes for accuracy
4, Check the bevel indicator. If indicator needs adjust-
ment use the phi!lips end of the combination wrench
supplied and slide the indicator to the correct reading
on the scale and retighten screw,
Bevel Pivot Adjustments
1, The miter saw should bevel easily by loosening the
bevel lock knob and tilting the power head to the left
If movement is tight or if there is looseness in the
pivot follow the adjustment procedure: a through c
a Loosen the bevel lock knob
b Turn the hex head screw with 1/2" socket clock-
wise to tighten or counter clockwise to loosen
c Recheck bevel movement of the miter saw
Readjust if necessary
BEVEL PIVOT
ADJUSTMENT
(RECESSED)
BEVEL
LOCKKNOB
BEVELINDEX
STOPS
BEVELINDEX
PIN
REAR, BOTTOM
VIEW FROM BACK
11
Page 12
Mounting The Miter Saw ....................................
WARNING: To avoid injury from unexpected
saw movement:
a. Before moving the saw, lock the miter (and
bevel if applicable) lock knob, and lock the
power head in the lower position using the
stop shaft. Unplug electric cord.
b. To avoid back injury, Hold the tool close to
your body. Bend your knees so you can lift
with your legs, not your back° Lift by using
the hand-hold areas at the bottom of the
base or the carry handle.
c. Never carry the miter saw by the power cord
or by the trigger grip of the plastic handle.
Carrying the tool by the power cord could
cause damage to the insulation or the wire
connections resulting in electric shock or
fire.
d. Place the saw so other people cannot stand
behind iL Thrown debris could injure people
in its path.
e. Place the saw on a firm, level surface where
there is plenty of room for handling and
properly supporting the workpiece.
f. Support the saw so the table is level and the
saw does not rock.
g. Bolt or clamp the saw to its support°
SMALLER HOLES
FOR"DRYWALL"
SCREWS
SMALLER HOLES
FOR"ORYWALL"
SCREWS
LARGERHOLES
FORs/16"BOLTS
LARGER HOLES
FORS/16"BOLTS
SMALLER HOLES
FOR"DRYWALL"
SCREWS
SMALLER HOLES
FOR "DRYWALL"
SCREWS
Place the saw in the desired location either on a work
bench or the recommended leg set, The base of the
saw has two sets of four holes to mount the miter saw,
four smaller holes for "Drywall" screws and four larger
holes for 5/16 bolts, (see illustration) If the saw is to be
used in one location, permanently fasten it to the work
bench or leg set,
Portable Applications
To mount the saw to a 3/4" piece of plywood, use the
5/16 bolt holes or the 4 drywall screw holes. The
mounting board can then be clamped down to prevent
it from tipping_ Plywood mount also helps protect saw
from damage during the rough handling associated with
portable miter saw usage,
Work Bench Applications
Mount as specified in portable applications Check for
workpiece clearances to left and right of saw_
Leg Set Applications
To mount saw to below mentioned leg set, use larger
holes in saw base Attach with hardware shown
through legset holes indicated by ,,o,, (see illustrations)
12
Page 13
Catalog No. 9-22246 Leg Set
Legset Mounting Holes for Miter Saws
1'I'
I O° °O
"%
0
o
o
o o
MOUNTING
HOLES
0 Oe °O I
/"
o
o
o
o
Mounting Board for Catalog No. 9-22244 Leg Set or
for Portable Applications
NOTE: Attach the mounting board to the leg set first
Then mount the saw to the mounting board using the
recommended hardware (not included)
Holes for mounting
board to legset
Ddii all holes 3_8" dia,
2[__+\ ,,°
9-7/a" 5"
Stiffener-Side Stiffener*End
Attach miter saw to holes indicated
Recommended mounting hardware (not included)
Qty
5/16-18xl -1/2" or longer hex head bolts 4
5/16-flat washers ............ 4
5/16 lockwashers ................ 4
5/16 hex nuts ...................... 4
CATALOG NO 9-22244 LEG SET
14" _
k -"_'_ FRONT _ _ Holes fo!
%4-1t4" _---_15-1t2" _ __._ mountinc
Mounting Board to legset Qty
5/16-18x1-1/2 hex head bolts .................. 4
5/t6 flat washers ........................ 4
5/!6 lock washers ............. 4
5/16 hex nuts ...................... 4
Mounting miter saw to mounting board Qty
5/16-t8x2 or longer hex head bolts ............. 4
5tl 6 flat washer .......................... 4
5/16 lock washer ......................... 4
5/16 hex nuts ....................... 4
0
24"_ =wt miter say
_000
C3
C3
CD
10"
FRONT
SiDE
13
L
o
i,,,, ,,,
_]OOO
14"
9-22244 Leg Set (Top View)
Attach mounting board to holes indicated
D
CD
C3
Page 14
SafetyInstructions For Basic Saw Operations
Before Using The Miter Saw:
WARNING: To avoid mistakes that could cause
serious, permanent injury, do not plug the
miter saw in until the following steps are com-
pleted,,
• Completely Assemble and Align Saw (See
"Assembly" and "AJignment" sections).
• Learn the use and function of the ON-OFF switch,
upper and lower blade guards, step shaft, bevel lock
knob (model 113 235220 & 113.235240 only) and
cover plate stop screw ("See Getting To Know Your
Miter Saw" Section )..
• Review and understand all safety instructions and
operating procedures in this manual.
• Review the maintenance methods for this miter saw.
(See Maintenance Section).
To avoid injury or death from electrical shock:
• Make sure your fingers do not touch the plug's metal
prongs when plugging or unplugging the miter saw
BEFORE EACH USE:
Inspect you saw.
Disconnect The Miter Saw. To avoid iniury from acci-
dental starting, unplug the saw, before changing the
setup, changing the blade or adiusting anything.
Compare the direction of rotation arrow on the guard to
the direction arrow on blade. The blade teeth shouid
always point downward at the front of the saw
Tighten the arbor screw
Tighten the cover plate stop screw
Check Damaged Parts. Check for:
Alignment of moving parts,
. Damaged electric cords,
• Binding of moving parts,
• Broken parts,
• Stable mounting
• Function of arm return spring and fower guard: Push
the arm all the way down, then let it rise up untit it
stops by itself Check the lower guard to see if it
closed fully If it did not, follow the instructions in the
"Trouble Shooting" section
• Other conditions that may affect the way the miter
saw works
Keep Guards in Place, in working order, and in proper
adjustment.
if any part of this miter saw is missing, bent, or broken
in any way, or any electrical parts don't work, turn the
saw off and unplug it. Replace damaged, missing, or
failed parts before using the saw again.
Maintain Tools With Care° Keep the miter saw clean
for best and safest performance Follow instructions for
lubricating. DON'T put lubricants on the blade while it's
spinning
Remove Adjusting Wrench and return it to proper
storage location before turning on tool
To avoid injury from jams, slips or thrown pieces:
° Use Only Recommended Accessories. (See
"Accessory" Section)° Consult this Owner's manual
for recommended accessories Follow the instruc-
tions that come with the accessories. The use of
improper accessories may cause risk of injury to
persons.
• Choose the right 10-inch diameter blade for the
material and the type of cutting you plan to do,
• Make sure the blade is sharp, undamaged and prop-
erly aligned With the saw unplugged, push the
power-head all the way down Hand spin the blade
and check for clearance. Tilt the power-head to 45
degree bevel and repeat the check
, Make sure the blade and arbor collars are clean.
• Make sure the collars' recessed sides are facing the
blade
o Using 1/4" hex end of combination wrench supplied,
make sure the arbor screw is firmly tightened.
• Make sure nil clamps and locks are tight and there is
no excessive play in any parts.
, Keep work area clean. Cluttered areas and bench-
es invite accidents. Floor must not be slippery
To avoid burns or other fire damage, never use the
miter saw near flammable liquids, vapors or gases
14
Page 15
Plan ahead to protect your eyes, hands, face, ears.
Know your miter saw° Read and understand the
owner's manual and labels affixed to the tool Learn its
application and limitations as well as the specific poten-
tial hazards peculiar to this tool
To avoid injury from accidental contact with moving
parts, don't do layout, assembly, or setup work on the
miter saw while any parts are moving
Avoid Accidental Starting. Make sure switch is "OFF"
before plugging miter saw into a power outlet
Plan your work.
Use The Right Tool. Don't force tool or attachment to
do a job it was not designed to do. Use a different tool
for any workpiece that can't be held in a solidly braced,
fixed position
CAUTION: This machine is not designed for
cutting ferrous metals (steel, iron and iron
based metals). Use this miter saw to cut only
wood, wood like products or soft metals like
aluminum. Other material may shatter, bind on
the blade, or create other dangers.
CAUTION: When cutting any metals, sparks or
hot fragments could cause a fire, To avoid this,
disconnect any dust collecting hose from the
miter saw, and remove all traces of wood dust
from inside dust traps in the miter saw.
Dress For Safety.
Any power miter saw can throw foreign objects into the
eyes This can result in permanent eye damage Wear
safety goggles (not glasses) that comply with ANSI
Z87.1 (shown on package). Everyday eyeglasses have
only impact resistant lenses, They are not safety glass-
es Safety goggles are available at Sears retail stores
Glasses or goggles not in compliance with ANSI Z87l
could seriously hurt you when they break
• Do not wear loose clothing, gloves, neckties or jew-
elry (rings, wrist watches) They can get caught and
draw you into moving parts
• Wear nonslip foOtwear
• Tie back long hair
• Roll long sleeves above the elbow
• Noise levels vary widely To avoid possible hearing
damage, wear ear plugs or muffs when using miter
saw for hours at a time
• For dusty operations, wear a dust mask along with
safety goggles,
Inspect your workpiece,
• Make sure there are no nails or foreign objects in the
part of the workpiece to be cut
Plan your work to avoid thrown pieces caused -
when the workpiece binds on the blade and is torn
from your hands.
Plan the way you will hold the workpiece from start to
finish:
Avoid awkward operations and hand positions where a
sudden slip could cause fingers or hand to move into
the blade.
Don't Overreach. Keep good footing and balance.
Keep your face and body to one side, out of line with a
possible throwback.
Never cut Freehand:
• Brace your workpiece solidly against the fence and
table top so it will not rock or twist during the cut.
• Make sure there's no debris between the workpiece
and its supports.
• Make sure no gaps between the workpiece, fence
and table will let the workpiece shift after it is cut in
two.
• Keep the cut off piece free to move sideways after
it's cut off, Otherwise, it could get wedged against
the blade and thrown violently
• Clear everything except the workpiece and related
support devices off the table before turning the miter
saw on,
• Secure Work. Use clamps or a vise to help hold the
work when it's practical.
Use extra caution with large, very small or awkward
workpieces:
• Use extra supports (tables, saw horses, blocks, etc)
for any workpieces large enough to tip when not
held down to the table top.
• Never use another person as a substitute for a table
extension, or as additional support for a workpiece
that is longer or wider than the basic miter saw table
or to help feed, support or pull the workpiece.
• Do not use this saw to cut pieces too small to let you
easily hold the work while you keep the thumb side
of your index (pointer) finger against the outside
edge of the fence
15
Page 16
• When cutting irregularly shaped workpieces, plan
your work so it will not slip and pinch the blade and
be torn from your hands. A piece of molding, for
example, must lie fiat or be held by a fixture or jig
that will not tet it twist, rock or slip while being cut°
* Properly support round material such as dowel rods,
or tubing,, They have a tendency to roll while being
cut, causing the blade to "bite," To avoid this, always
use a fixture designed to properly hold your work-
piece
WARNING: If planning to cut aluminum or other
non-ferrous metals: Under adverse conditions,
the blade can grab and throw the workpiece
suddenly and unexpectedly. To avoid injury,
follow all applicable safety instructions, as you
normally would, and:
• Use only sawblades specifically recom-
mended for non-ferrous metal cutting.
, Do not cut metal workpieces that must be
hand held. Use auxiliary clamps or other
equipment as needed.
, Cut non-ferrous metals only if you are expe-
rienced or under the supervision of an expe-
rienced person.
Whenever Saw Is Running:
WARNING: Don't allow familiarity (gained from
frequent use of your miter saw) cause a care-
less mistake. A careless fraction of a second is
enough to cause a severe injury.
Before starting your cut, watch the miter saw while it
runs. if it makes an unfamiliar noise or vibrates a lot,
stop immediately. Turn the saw off, Unplug the saw, Do
not restart until finding and correcting the problem
Keep Children Away, Keep all visitors a safe distance
from the miter saw, Make sure bystanders are clear of
the miter saw and workpiece,
Never confine the piece being cut off, Never hold it.
clamp it,touch it. or use length stops against it while the
blade is spinning, tt must be free to move sideways on
its own, If confined, it could get wedged against the
blade and thrown violently
Let the blade reach full speed before cutting.,
Don't Force Tool. It will do the job better and safer at
its designed rate, Feed the saw into the workpiece only
fast enough to tet the blade cut without bogging down
or binding.
Before freeing jammed material:
• Turn switch "OFF",
• Unplug the miter saw
• Wait for aflmoving parts to stop
After finishing a cut:
Keep holding the power head down
• Release the switch, and wait for all moving parts to
stop before moving your hands,
• If blade, doesn't stop within 6 seconds, unplug the
saw and follow the instructions in the Trouble
Shooting section for fixing the blade brake before
using the saw again,
Before Leaving The Saw;
Never Leave Tool Running Unattended. Turn power
off, Wait for all moving parts to stop,
Make workshop child-proof, Lock the shop,
Disconnect master switches, Store tool away from chil-
dren and others not qualified to use the tool
Basic Saw Operations
WARNING: For your convenient use, your saw
has a blade brake. The brake is not a safety
device. Never rely on it to replace proper use of
the guard on your saw. If the blade does not
stop within 6 seconds, unplug the saw and fol-
low the instructions in the Trouble Shooting
section for fixing the brake before using saw
again.
Body and Hand Position
Proper positioning of your body and hands when oper-
ating the miter saw will make cutting easier and safer,
Never place hands near cutting area, Place hand at
least 4" from path of blade, Hold workpiece firmly to the
fence to prevent movement toward the blade, Keep
hands in position until trigger has been released and
the blade has completely stopped Before making a cut,
make a "dry run" with the power off so you can see the
3ath of the blade,
WARNING: Do not try to cut short pieces, you
cannot properly support the workpiece an__d.d
keep your hold down hand the required dis-
tance from the blade.
16
Page 17
Basic Saw Operations (Continued)
Miter Cut
When a miter cut is required, loosen the miter lock
knob, depress the index spring, and move the saw to
the desired angle, Retighten miter lock knob Do not
stand in front of the saw table Move with the handle to
the miter angle to make the cut
E
/
/
I WiTHMITER
_._ MOVE FEET
ANGLE t
Bevel Cut
Model 113.235220 & 113.235240 Compound
Miter Saw Only:
When a bevel cut is required, loosen bevel lock knob,
tilt the blade to desired bevel angle Lock the bevel lock
knob. Stand to the left side of the handle to make the
cut.
Overriding the Bevel Stops
Use the 0° and 45=bevel stops for precise, repeatable
bevel indexing,
Occasionally, when cutting a bevel or compound cut,
you may need to set the bevel angle a small amount
beyond the 0° or 45° bevel stop, This is very easily
done by pulling the bevel index pin out and locking the
bevel knob,
BEVEL
LOCK KNOB
BEVELINDEX
PiN
17
BEVELINDEX
STOPS
REAR, BOTTOM
VIEW FROM BACK
Page 18
Basic Saw Operations
Compound Cut
Model 113.235220 & 113,235240 Compound
Miter Saw Only:
When a compound cut is required, select the correct
bevel and miter pesitionr Move your feet and body with
the handle to the desired miter angle to make the cut.
Cutting Bowed Material
Before cutting a workpiece, check to make sure it is not
bowed, if it is bowed the workpiece must be positioned
and cut as illustrated Do not position workpiece incor-
rectly or try to cut the workpiece without the support of
the fence. This wilt cause pinching of the workpiece on
the blade. The workpiece could suddenly jump or move
and your hand could hit the blade,
CORRECT
INCORRECT
18
Page 19
Basic Saw Operations (Continued)
Workpiece Support
Long pieces need extra supports. The supports should
be placed along the workpiece so the workpiece does
not sag and your hand holding the workpiece is posi-
tioned 4" or more from the blade path. The support
should let the workpiece Iay flat on the base and work
table during the cutting operation
NOTE: When mounted on a large flat surface, the
miter saw table is 3-1/2" high. Two finished 2x4's on
their sides can be used as work support extension.
Auxiliary Fence
Certain types of molding need a fence face extension
due 1:othe size and position of the workpiece_ Slots are
provided in the fence to attach an auxiliary fence. Get a
straight piece of wood typically 1/2 inch thick by 3-1/4
inches high by 19-1/4 inches long. To attach auxiliary
fence, place the piece of wood on the miter saw fence.
Mark the locations from the backside of the miter saw
fence. Drill 200"-250" holes, then countersink the
holes on front of wood to receive #10 fiat head screws.
Attach the auxiEiary fence securely and make a full
depth cut. This will create the blade slot Check for
interference between the auxiliary fence and lower
bfade guard Correct any interference before proceed-
ing. The auxiliary fence is used with the saw in the 0°
bevel position If a bevel cut is desired, the auxiliary.
fence will have to be removed
19
Page 20
Basic Saw Operations .....................................
MITER SAW
FENCE --_
Cutting a Dimensional 4x4 (3-1/2" x 3-1/2" actual)
with one cut.
A dimensional 4x4 may be cut with one cut by attaching
an auxiliary fence of 7/8 thickness, with screws to the
miter saw fence as shown on previous page,,
!
'_-- MITER SAW
TABLE
Vertical Bevel Cutting
To make a miter cut in a 2x4 workpiece (actual 1-5/8" x
3-1/2") in the vertical position (on edge) a spacer, such
as the auxitiary fence described in the previous page, is
required•
MITER SAW
FENCE
f
2O
WORKPIECE
3-1/2"
j /-- MITER SAW
I f TABLE
I
Page 21
Basic Saw Operations (Continued)
Tips for Cutting Compound Miters
Model 113.235220 & 113,235240 Only:
A compound miter is a cut requiring both a miter setting
and bevel setting A compound miter is used for making
frames or boxes that have sloping sides and are wide
at one end and narrow at the opposite end, Compound
miters are "tricky" to make because the miter setting
and bevel setting are directly related to each other
Every time the miter setting is changed the bevel set-
ting must also be adjusted; likewise every adjustment to
bevel requires a corresponding adjustment to miter,
Because it may take several tries to obtain the desired
angle it as advisable to make test cuts in a scrap piece
of material.
Cutting Crown Moldings
Plan Ahead so that you are not tempted to reach
across saw blade to steady newly severed workpiece
Two Methods to Cut Crown Moldings
1, Workpiece standing up, usua!ly cut inverted from
ceiling mounted orientation. Fixturing: Accessory
mounted crown molding jigs which locate workpiece
See recommended accessories (Table clamp is
helpful) Hand is on fence when the cuts are made.
All cuts are made at 0° bevel setting (see illustra-
tion).
Alternate fixturing: Auxiliary fence as shown on page
19 plus table clamps.
2. Workpiece lying flat for compound cut (see chart),
Model 113,235220 & 113.235240 Only:
Tips For Cutting Crown Molding Lying Flat
Model 113,235220 & 113.235240 Only:
A compound miter saw is excellent for cutting crown
molding. Crown molding is difficult to cut because in
order to fit correctly it must be precisely mitered,
All Standard (US) crown molding has a top rear angle
(fits next to ceiling) of 52 ° and a bottom rear angle (fits
against wall) of 38°
NOTE: Above angles assume that the constructed wall
corner is exactly 90" In typical construction, this is not
always the case. Measure wall and make necessary
adjustments to angles
Inside ._
Corner f X_
Miter and Bevel Settings for Standard
Crown Molding Lying Flat on Miter Saw
Table.
BEVEL MITER TYPE OF CUT
SETTING SETTING
LEFT SIDE,INSIDE CORNER
338 ° 31 6°
Right
33 8° 31 6 °
Left
33 8° 3! 6°
Left
338 ° 31 6 o
Right
I Position top molding against
fence
2 Left side is finished piece
RIGHTSIDE, INSIDECORNER
1 Positionbottomof molding
againstfence
2 Leftside is finished piece
LEFT SIDE,OUTSIDECORNER
1 Positionbottomof molding
againstfence
2 Right sideis finished piece
RIGHT SIDE, OUTSIDE CORNER
1 Position top of molding
against fence,
2 Right side is finished piece
NOTE: On all above
cuts lay molding with broad back
surface flat on table
PRETESTING COMPOUND SETTINGS ON SCRAP
MATERIAL IS EXTREMELY IMPORTANT!
21
Page 22
Maintenance and Lubrication
Maintenance
DANGER: Never put lubricants on the bladewhile it's spinning.
starting or electrical shock, unplug the power
WARNING: To avoid injury from unexpected
cord before working on the saw.
WARNING: For your safety, this saw is double
insulated+ To avoid electrical shock, fire or
injury, use only parts identical to those identi=
fled in the parts list reassemble exactly as orig-
inal assembly to avoid electrical hazards.
Replacing Carbon Brushes
The carbon brushes furnished wilt last approximately 50
hours of running time or t0,000 on/off cycles Replace
both carbon brushes when either has tess than 1/4"
length of carbon remaining To inspect or reptace first
unplug the saw Then remove the motor cap on the end
of the motor by removing 2 screws. Remove the lead
wires from the tabs on the brushes, then pull out the
brushes To reassemble reverse the procedure. Tighten
the screws snugly but do not overtighten,
NOTE: To reinstall the same brushes, first make sure
the brushes go back in the way they came out. This will
avoid a break in period that reduces performance and
increases wear,
Lower Blade Guard
Do not use the saw without the lower guard The lower
blade guard is attached to the saw for protection
Should the tower guard become damaged, do not use
the saw until damaged guard has been replaced,
Develop a regular check to make sure the lower guard
is working properly Clean the lower guard of any dust
or build up with a damp cloth,
CAUTION: Do not use solvents on the guard.
They could make the plastic "cloudy" and brittle.,
WARNING: When cleaning lower guard unplug
the saw from the outlet to avoid unexpected
start-up.
Saw Dust
Periodically, sawdust will accumulate under the work
table and base This could cause difficulty in the move-
ment of the work table when setting up a miter cut.
Frequently biow out or vacuum up the sawdust
eye protection to keep debris from blowing into
WARNING: If blowing sawdust, wear proper
eyes,
Lubrication
Aft the motor bearings in this toot are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions, therefore,
no further lubrication isrequired. (See below.)
infrequent Lubrication as Required:
1. Lubrication of arm pivot for free movement.,
a Apply oil between washer and contact face of
Table/Pivot casting.
b Apply oil to pivot shaft nex_ to inside surface of
ears on arm casting
NOTE: Disassembly should be done by an authorized
service technician, Removal of the upper guard and the
stopshaft is necessary before pivot can be disassem+
bled Pay close attention to the spring-end positions in
the castings mark with chalk to avoid later confusion.
2. Lubrication of mechanism which pivots lower guard:
(see picture) Use light household oil (sewing
machine oit) or a pressurized light spray oil on metal-
to-metal or metal-to-plastic guard contact areas as
required for smooth, quiet operation Avoid excess
oil to which sawdust will cling Lubricate the lower
guard spacer, roller, pivot plate and link pivoL
3 Lubrication of miter index indents: Use a small
amount of grease on the miter index indents that are
located below the table on the front of the unit
LINK LOWER
PIVOT ROLLER
GUARD
SPACER
MITER iNDEX
iNDENTS (5)
\
PIVOT
PLATE
22
Page 23
Sears Recommends the Following Accessories
Recommended Accessories
sories, use only accessories shown on the rec-
I WARNING: To avoid injury from unsafe acces-
ommended accessories list in this manual.
Prohibited Accessories
The use of any cutting tool except 10" saw blades
which meet the requirement under recommended
accessories is prohibited, Do not use accessories such
as shaper cutters or dado sets, Ferrous metal (metal
with iron in it) cutting and the use of abrasive wheels
are prohibited, See WARNING and CAUTION notes in
the "Safety Instructions For Basic Saw Operations"
Section_ If planning to saw nomferrous metal see those
WARNING and CAUTION notes in the "Safety
Instructions For Basic Saw Operations" Section,
Leg Sets .......................................................... 9-22244
...............................................................................9-22246
Carbide-Tipped Blades:
Trim Saw .........................................................See Catalog
Cut-Off ...........................................................See Catalog
Combination ............................................... See Catalog
Plywood/Particle Board .............................. See Catalog
Non-Carbide Tipped Blades:
Cross Cut/Plywood .......................................See Catalog
Combination ................................................. See Catalog
Clamp ...................................................................9-29000
Table Extensions ............................................... 9-2900l
Crown Molding Jig ................................................9-29002
Dust Bag ............................................................ 9-23467
1-1/4" Sawdust Collector Hose ..................... 9-17866
Basic Blade Requirements
10" Diameter
Blades marked for 5,500 RPM or higher
5/8" Diameter Arbor Hole
23
Page 24
Trouble Shooting Guide ° Motor ........................
PROBLEM PROBABLECAUSE SUGGESTED CORRECTIVEACTION
Brake does not stop 1
blade within
6 seconds. 2..
3 Arbor screwlooser
4 Other
Motor does not start.
Brush sparking when
switch released.
1 Fuse,
2 Brushes worn.,
3. Other,
1 Normal-automatic brake
Brushes not seated
or lightly sticking.
Motor brake winding-
overheated from use of not-
recommended blade
or rapid on/off cycling
working properly
-Inspect/clean/replace brushes
(see maintenance section).
-Use a recommended blade
-Let cool down
-Retighten
-Authorized service. Check motor brake winding,
switch, condition of commutator,
-15-Amp time delay fuse, or circuit breaker
-See "Maintenance" section,
-Authorizedservice
-None
Trouble Shooting Guide o General .............
PROBLEM
Blade hits table.
PROBABLE CAUSE
1 MisalignmenL
SUGGESTED CORRECTIVE ACTION
-Get authorized Sears Service,
Angle of cut
not accurate.
Can't move
miter adjustment°
Power-head
wobbles.
Power-head
won't fully rise or blade
guard won't fully close,
Blade binds, jams,
burns wood.
Tool vibrates or
shakes.
1 Misalignment
1 Sawdust under table
1 Loose pivot points
1 Part failure.,
2, Pivot spring not replaced
properly after service
3 Sawdust build-up
1 improper operation.
2 Dull blade
3 improper blade
4, Warped blade
1. Saw blade not round
2. Saw blade damaged.
3 Saw blade loose,-
4 Other.
-See "Alignment" section.,
-Vacuum or blow out dust
WEAR EYE PROTECTION
-See "Alignment" section,
-Get authorized Sears Service,,
-Get authorized Sears Service
-Clean and lubricate moving parts,
-See "Basic Saw Operation" section,,
-Replace or sharpen blade.
-Replace with 10" diameter blade designed
for the material being cut,
-Replace blade.
-Replace blade.
-Replace blade
_Tighten arbor screw.
-Get authorized Sears Service.
Power head is difficult
to move down from
upper stop.
t Mechanism which pivots
lower guard is sticking,
2 Sawdust build-up in
guard area,
-Clean and lubricate lower guard mechanism
(See lubrication instructions on page 22)
-Clean and lubricate lower guard mechanism (See
lubrication instructions on page 22)
24
Page 25
WHITE
FIELD WINDING
BLACK
WlDE BLADE WIRE
NUT
ii [ lllllll[BW '
_ BLACK
POWER CORD
"==e3
SPDT SWITCH
Circuit Diagram
Trouble Shooting of brake by qualified ser-
vice person only.
I. Check commutation at no load. If there is a heavy
sparking which follows the curvature of the commu-
tator: replace the armature
2 To continue trouble shooting, now unplug the power
cord
3. Install new brushes,especially if delayed come-in of
brake has been noticed before failure.
4 Check brake circuit for continuity: remove motor cap
and brushes, Use ohmmeter to check continuity from
brush terminal to brush terminal If open, locate
exact place using ohmmeter. As indicated by test,
tighten connection or replace field assembly or
replace switch
5. After repair, check direction of blade rotation vs
guard arrow.
BRUSH #1
BRUSH #2
BLACK
25
Page 26
Repair Parts ...................
PARTS LIST FOR CRAFTSMAN 10" MITER SAWS
MODEL NO. 113.235220 & 113,235240 AND 113.235110
18
FIGURE 1
19
20
21
17
13
A MODEL113235220 &
1t 3 235240 ONLY
26
Page 27
Repair Parts
PARTS LIST FOR CRAFTSMAN 10" MITER SAWS
MODEL NO. 113.235220 & 113.235240 AND 113,235110
FIGURE 1
Always order by Part Number m Not by Key Number
Key Part Description
No. No.
1 See Fig 4 Blade Guard Asm
2 See Fig 2
3 823234
823230
4 823296
5 823313
6 823236
823232
7 823228
8 823295
9 823297
10 805553-4
11 9421621
12 38724
*Standard Hardware Item -- May Be Purchased Locally
A Model 113,235220 & 113 235240 Only
_1 Model 113,235110 Only
_ WARNING: These items are important to the safety of this tool, Do not substitute common parts,
Motor Asm
_Table
I_1Table (not shown)
_Foot Locking
Knob
_kFence
181Fence (not shown)
Base
Shim Table
Spring Index
Washer 2t/64 x 9/16 x 3/64
Scr Soc Cap 5/16 - 18 x 5/8
Pointer
Key Part
No. No.
13 436594
14
9416630
15
823326
16
823327
17
821421-6
18
823314
19
9416187
20
60039
21
See Fig 3
SP5990
Description
Screw Pan Hd Type "F'
8-32 x 5/16
Screw Hex Type 'T'
5/16-18 x 1
A Stop Bevel
Alndicator Bevel
_kO-Ring
Wrench Combination
_kScrew Hex Type "T"
5/16-! 8 x 3/4
,&.Washer 380 x 47/64 x 1/16
Pivot Asm_
Owners Manual
(not illustrated)
]
27
Page 28
Repair Parts ...............................
r_n I o L_ i FOR _.R_F'r, S_,_N 10" ,_.T_.r, SAWS
NOD EL NO. 'I13.235220 & 113.235240 AND 113.235110
FIGURE 2---ARM AND MOTOR ASSEMBLY 1
13
%!4 15
5
11 17
10
WARNING: For your safety, this miter saw is specially insulated° To avoid electrical shock, fire or injury, use
only parts identical to those identified in the parts list, Reassemble exactly as originally assembled.
Alwm,s order by Part Number -- Not by Key Number
Key
No,
1
2
3
4
5
6
7
8
9
9
10
11
12
13
13
14
15
16
t7
t8
19
Part
No.
823290
808380-5
823286 iA.
823289
823287
823281
823277 _.
354653
823955
823841
823323
823322
823417
823284
823284-1
803709-1
823288
823283
808277-11
STD551210
STD551010
,_ o_kMotor/Gear Box
_, Button Lock
Description
Handle Right Half
Screw Pan Cr #8 P
Switch SPDT
Spring Trigger
Trigger
Brush
Holder Brush
Bumper
-_ Motor!Gear Box
_.Lock Arbor
_,Spring Arbor Lock
Seal
•_Cord W/Plug
•mCord W/Plug
Connector Wire
Cap Motor Housin
Screw Pn Hd. 10-',
2-1/4
• Lockwasher Ext #1
• Washer 13/64 x 3/I
1/32
_k Model 113 235220 & 113,235240 Only I_ Model 1!3 235110 Only
,_ WARNING: These items are important to the safety of this tool. Do not substitute common parts. 1
_:CAUTION: See Mechanical Assembly Caution below. I
*WARNING: Any attempt to repair or replace electrical parts on this unit may create a Hazard unless repair
is done by a qualified service technician° Repair service is available at your nearest Sears store.
28
J
Page 29
Repair Parts ....................
PARTS LIST FOR CRAFTSMAN 10" MITER SAWS
MODEL NO, 113.235220 & 113.235240 AND 113.2351!0
FIGURE 3--PIVOT ASSEMBLY
2 3 4
6
5
Always order by Part Number-- Not by Key Number
Key--- Part Description
NO. No.
1 803309-2 Screw Set Hex Soc,
Locking 10-32 x 3/8
2
823324
3
821421-2
4
823302
5
805606
6
803899-5
7
823328
8
823298
9
823301
*Standard Hardware Item -- May Be Purchased Locally
_k Model t!3235220 & 113 235240 Only
[] Model 113235110 Only
$ CAUTION: See Mechanical Assembly Caution on page 31.
• WARNING: Uncontrolled spring release of mistnstallation of these parts may create a Hazard unless repair
is done by a qualified service technician, Repair service is available at your nearest Sears store,
WARNING: These items are important to the safety of this tool, Do not substitute common parts,
APivot
O-Ring
Shaft Stop
Ring Retaining
Washer Thrust
,_ • SSpring Torsion
Spacer Spring
Shaft Pivot
29
Page 30
PARTS LIST FOR CRAFTSMAN 10" MITER SAWS
MODEL NO. 113.235220 & 113.235240 AND 113.235110
FIGURE 4
I
19
18
16
03
O
14
17
8
7
9
13
12
11
Page 31
PARTS LIST FOR CRAFTSM_N 10" MITER SAWS
MODEL NO. 113.235220 & 113.235240 AND 113.235110
FIGURE 4
Key
No.
1
2
3
4
5
6
7
8
9
10
10
11
12
13
CO
..&
14
15
16
I7
18
19
Part
No.
820536
823956
823300
823251
821421-3
STD601105
823307
60288
823303
9-32194
9-32138
823304
823291
821521-2
823305
821521-1
823840
823292
821521
823306
Description
Dust Elbow
Arm/Guard
Washer Cup
Arbor
Ring "O"
* Screw Pan Cr Ty 'T'
10-32 x 1/2
Bumper Guard
Screw Lock Set 1/4-20 x 3/8
Collar Blade
At Blade Saw
It Blade Saw
Screw Blade
SGuard Lower
Screw Shoulder
Unk Actuator
Retainer Guard
• $Spnng Guard
!_ Screw Shoulder
Screw Shoulder
l Bearing Cam
dtStock Item - May be secured through the hardware
epartment of most Sears retail stores.
,& Model 113.235220 & 113.235240 Only
I_ Model 1_3.235110 Only
_O
"O
mm
"13
U)
, WARNING: These items are important to the safety of this tool, Do not substitute common parts.
CAUTION: See Mechanical Assembly Caution below.
• WARNING: Uncontrolled spring release or misinstallation of these parts may create a Hazard unless repair
is done by a qualified service technician, Repair service is available at your nearest Sears store.
CAUTION: Mechanical Assembly, to qualified service technician.
I. Wear approved eye protection when working with coil spring including spring, arbor lock 823322.
2. Incorrect re-assembly of torsion spring 823328 can cause an unsafe condition because cutting head fails
to rise fully to stop, or because spring fails through over-stress.
3. Improper reassembly of mechanisms controlling movement of lower guard 823292 can cause an unsafe
condition because guard fails to operate freely as cutting head is moved up and down.
I
Page 32
f
owner's
manual
SERVICE
MODEL NO.
113.235220
&
] 13.235240
COMPOUND MITER SAW
I INCH
SAW
Now that you have purchased your 10 inch Miter Saw, should a
need ever exist for repair parts or service simply contact any
Sears Service Center and most Sears, Roebuck and Co. stores
Be sure to provide all pertinent facts when you call or visit,
The model number of your 10 inch Miter Saw will be found on a
plate attached to your saw
113=235110
NON-COMPOUND MITER
SAW
IF YOU NEED REPAIR
SERVICE OR PARTS:
For repair service, call this toll
free number:
1-800-4-REPAIR
(1-800473-7247)
For replacement parts
informationand ordering, cal!
this toll free number:
1-800-FON-PART
(t-800-366-7278)
J
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING
INFORMATION:
PARTNUMBER
MODEL NUMBER
113235220
&
113235240
113,235110
All parts listed may be ordered from any Sears Service Center
and most Sears stares, If the parts you need are not stocked
locally, your order wil! be electronically transmitted to a Sears
Repair Parts Distribution Center for handling, /
10" NON-COMPOUND MITERSAW
PARTDESCRIPTION
NAME OF ITEM
10" COMPOUND MITERSAW
Part No, SP5990
Sears, Roebuck and Co., Hoffman Estates 60179 U.S.A.
Printed in U,SA. 10/96
Loading...