Sears 113.20680, 113.206930 User Manual

k •::

.... :/i "< i¸

MODEL NO.

]]3.20680

JOINTER/PLANER ONLY

'_,/,_ __ _ i_: _i, _ ,///i ...... • ',

113.206930

JOINTER!PLANER WITH

LEGS AND MOTOR

Serial

Number .......................................

Model and serial number may be found

on a plate attached to your infeed table.

You should record both model and serial number

in a safe place for future use.

CAUTION:

Read GENERAL and ADDiTiONAL SAFETY

iNSTRUCTiONS carefully

CRn MaNo

6_- INCH JOIN TER-PLANER

® assembly ® operating

o repair parts

Sotd by SEARS, ROEBUCK. AND CO., Chicago, _t. 60684 U.S.A.

PartNo.67036 :..........' : : :: ':

FULLONEYEAR WARRANTY ON CRAFTSMAN JOINTER/PLANER

year from the date of purchase, this Craftsman Jointer/Planer fails due to a defect in material

rs will repair it, free of charge.

,VAtLABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE

THROUGHOUT THE UNITED STATES.

you may also have other rights which vary from state to

SEARS,

general safety instructions

1.:KNOW YOUR POWER TOOL

Read the owner's manual carefully. Learn its

application and limitations as well as the specific potential hazards peculiar to this tool.

2.:GROUND ALL TOOLS

This tool is equipped with an approved 3.conductor

c0rd and a 3-prong grounding type plug to fit the

proper grounding type receptacle The green conductor in the cord is the grounding wire. Never connect the

green wire to a live terminal.

3; KEEP GUARDS IN PLACE

in working order, and in proper adjustment and

alignment,

4. REMOVE ADJUSTING KEYS

AND WRENCHES

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

5: KEEP WORK AREA CLEAN

Cluttered areas and benches invite accidents. Floor must not be Slippery due to wax or sawdust.

6;:!AV01D DANGEROUS ENVIRONMENT

D0n't use power tools in damp or wet locations or expose them to rain; Keep work area well lighted;

Provide adequate surrounding work space.

7. KEEP CHILDREN AWAY

All visitors-should be kept a safe distance from work

area.

8. MAKE WORKSHOP KID-PROOF

-- with padlocks, master switches, or by removing starter keys,

9. DON'T FORCE TOOL

it will do the job better and safer at the rate for which it was designed.

10. USE RIGHT TOOL

Don't force tool or attachment to do a job it was not

designed for.

11. WEAR PROPER APPAREL

Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches} to get caught m moving parts.

Nonslip footwear is recommended. Wear protective hair covering to contain tong hair. Roll long sleeves

above the elbow.

12. USE SAFETY GOGGLES

WearSafety goggles (must comply with ANS! Z87.1 )

at all times,; Ats0, use face or dust mask if cutting

operation is dusty, and ear protectors (plugs or mUffs) Turn power off. Don't leave tool until it comes to a during extended periods of operation: complete stop.

CO,; Sears Tower, BSC 41-3. Chicago. IL 60684

for power fools

13. SECURE WORK

Use clamps or a vise to hold work when practical It's safer than using your hand, frees both hands to operate

tool.

14. DON'T OVERREACH

Keep proper footing and balance at all times,

15. MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

16. DISCONNECT TOOLS

before servicing; when changing accessories such as blades, bits, cutters, etc.

17. AVOID ACCIDENTAL STARTING

Make sure switch is in "OFF" position before plugging in,

18. USE RECOMMENDED ACCESSORIES

Consult the owner's manual for recommended accessories, Fol}ow the instructions that accompany

the accessories. The use of improper accessories may cause hazards.

19: NEVER STAND ON TOOL

i: i ::":i Seri0us injury could occur if the toot is tipped or if the

cuttin£ tool is accidentally contacted. DO not store materials above or near the tool such that

it isnecessary to stand on the too_ to reach them.

CHECK DAMAGED PARTS

20.

Before further use of the too!, a guard or other part that

is damaged should be carefully checked to ensure that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other

conditions that may ,affect its operation. A guard or

other part that is damaged should be properly repaired

or replaced.

21. DIRECTION OF FEED

Feed work into a blade or cutter against the direction

of rotation of the blade or cutter only.

22. NEVER LEAVE TOOL RUNNING UNATTENDED

Safety is a combination Of operator common sense and alertness at all times when the Jointer-Planer is being used.

WARNING: FOR YOUR OWN SAFETY, DO NOT AT- TEMPT TO OPERATE YOUR JOINTER-PLANER UNTIL

IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE INSTRUCTIONS, .. AND UNTIL YOU HAVE READ AND UNDERSTOOD THE FOLLOW- ING,

PAG E

1. GENERAL SAFETY iNSTRUCTIONS FOR POWER

TOO LS .................................. 2

2. GETTING TO KNOW YOUR JOINTER-PLANER 12

3. BASIC MACHINE OPERATION ............... 18

4. USE OF HOLD-DOWN/PUSH BLOCKS ......... 19

5. MAINTENANCE ........................... 21

6. STABILITY OF MACHINE

If there is any tendency for the Jointer-Planer to tip over or move during certain operations such as when planing or jointing long heavy boards, the Jointer-

Planer (stand) should be bolted to the floor.

7. LOCATION

The Jointer-Planer should be positioned so neither the operator nor a casual observer is forced to stand in line

with the wood while it is being planed.

This machine is intended for indoor use only. Provide

adequate lighting.

8. KICKBACKS

Kickbacks can cause serious injury. A kickback occurs when the operator looses control of the workpiece

causing it to be kicked back toward him.

9. PROTECTION: EYES, HANDS, FACE, EARS, BODY

a, ¸ if any part of your jointer is malfunctioning, has been

damaged or broken.., such as the motor switch, or other operating control, a safety device or the power

cord . . . cease operating immediately until the

particular part is properly repaired or replaced.

b. Wear safety goggles that comply with ANSI Z87.1

and a face shield if operation is dusty. Wear ear ptugs

or muffs during extended periods of operation.

Do not plane, joint, or bevel wood shorter than 12

in. Smaller pieces of wood can tip over on the tables, or into the cutterhead and be kicked back to- ward you.

Always use the hold down/push block when jointing

or beveling wood narrower than 3 in. but never joint

or bevel wood narrower than 3/4 in, under any cir-

cumstances.

Always use the hold down/push blocks when planing wood thinner than 3 in. but never plane wood thinner

than 1/2 in. under any circumstances.

Avoid awkward hand positions, where a sudden slip

could cause a hand to move into the cutters.

Never turn your Jointer-Planer "ON" before clearing

the table(s) of all objects (tools, scraps of wood, etc.)

except for the workpiece and related feed or support

devices for the operation planned.

Make sure the cutterhead revolves in the right direc- tion, (toward the infeed table).

KEEP CUTTER GUARD IN PLACE AND OPERAT- ING PROPERLY AT ALL TIMES. Regularly check

the tension of the cutter guard spring to assure satisfactory operation. (See Getting To Know Your

Jointer-Planer section.)

Kickbacks - and possible injury from them can usual]y be

avoided by:

a. Holding the workpiece firmly against tables and fence.

b. Not taking too deep a cut at one time. A deep cut

requires more effort to feed the wood while planing and can cause the wood to kickback. A cut between

1/32 and 1/16 of an inch deep will produce the best results.

C, Not jointing, planing, or beveling pieces of wood

smaller than recommended. (See section in this man- ual, "BasicJointer-PIaner Operations.") Smaller pieces of wood can tip over on the tables, or into the cutter

head and can be kicked back toward you.

d, Keeping blades sharp. Blades that are dult or nicked

require more effort while planing and wilt tend to pound the wood rather than cut it, which can cause

the wood to kickback. A nicked blade will cut a rid- ge in your wood and cause the wood to ride up on the

outfeed table. Make sure the cutter blades are in- staIted properly, and cutter blade wedge screws are

tight.

Always feed the wood completely through the cutter head and past the cutter guard so that the guard re-

turns to the rest position against the fence. When

using only one hold down/push block to feed the wood, do not place your other hand on the Jointer-

Planer.

10. Warped wood should be surface planed on the concave side for best results.

11. To avoid a rough planed surface, determine if possible, which way the grain emerges from the wood and feed the wood accordingly.

"_'_ GRAIN EMERGING

12. Do not plane edges of plywood, composition materials, or wood that has glue on it or is painted or varnished. Planing these materials will dul! the btades quick!y.

Safety instructions

for iointer-pQaner

13,:To be sure you will make adepth of cut as planned,

always lower tl_e infeed table slightly beyond the

depth Wanted. then raise the table to the desireddepth.

14. When _aning, jointing, orl beveling wood over four {4) feet :long, make. sure it is supported at table heig:ht.

15. Never leave the Jointer-Planer work area with the power on, before the 3ointer-Ptaner has come to a complete

stop; or without removing and storing the switch key.

16, Never operate the Jointer-Planer with protective cover

on the unused shaft end of the motor removed.

WARNING: THE 2" JOINTER-PLANER PULLEY AND

THE 2-1/2" MOTOR PULLEY FURNISHED WILL RUN THE CUTTER HEAD AT APPROXIMATELY 4300 RPM WHEN USED WITH A 3450 RPM MOTOR, NEVER

SUBSTITUTE OTHER PULLEYS TO INCREASE THIS SPEED BECAUSE tT COULD BE DANGEROUS

WARNING: DO NOT ALLOW FAMILIARITY (GAINED

FROM FREQUENT USE OF YOUR JOINTER-PLANER)

WEAR YOUR

The operat:_or_ of arw power tDo! car_ result in foreign objects being thrown into the eyes, which can result in

severe eye damage. Always wear safety goggles complying with ANS_i Z87.1 (shown on Package) before commencing power tool operation. Safety Goggles are available at Sears reta_| o'rr catalog storeS.

TO BECOME COMMONPLACE. ALWAYS REMEMBER THAT A CARELESS FRACTION OF A SECOND 1S SUFFICIENT TO INFLICT SEVERE INJURY.

t 7. Readand followthe instructions appearing on the danger

ta_! on the cutter guard.

DANGER

FOR YOUR OWN SAFETY

READ AND FOLLOW SAFETY iNSTRUCTIONS IN OWNERS MANUAL BEFORE OPERATING THiS MA-

CHIME,

NEVER OPERATE THIS MACHINE WITH THE CUT- TER GUARD, SLIDING GUARD OR BELT GUARDS

REMOVED.

NEVER MAKE JOtNTtNG OR PLANING CUTS DEEP- ER THAN 1!16iNCH.

ALWAYS USE HOLD DOWN/PUSH BLOCKS FOR JOINTII_G MATERIAL NARROWER THAN 3 INCHES OR PLANING MATERIAL THINNERTHAN 3 INCHES,

POWER TOOL GUARANTEE ................... Z

GENERAL SAFETY INSTRUCTIONS FOR

POWER TOOLS .... ........................... 2

ADDITIONAL SAF ETY INSTR UCTIONS FOR

JOINTER-PLANER ............................ 3

MOTOR SPECIFICATIONS AND ELECTRICAL

REQUIREMENTS _. ........ ................... 5;

Connecting to Power Source Outlet .............. 5

Check Motor Rotation ........................ 5

UNPACKING AND CHECKING CONTENTS ........ B

ASSEMBLY ..................... ; ............ 7

Assembling Steel Legs ; ._ ................... 7

Mounting Jointer-Ptaner On Recommended

: Checking Cutterblade Sci;ews:..: :.. ;,.:.. : ;., 8

Installing Sliding Guard;. _..... q;::o:'_:::...:, : ;i .. E_

..... Mounting Recommended Craftsman M0torl and

i Belt Guards ........ 9

Check Motor Rotation.. ..... :....... . .. ;, . .... . 10

Jointer-Pulley Belt Guard Instaiiation _:,::. i. ..... 11

J J UJJ/L i J] ........

GETTING TO KNOW YOUR JOINTER-PLANER .... 12

Depth of Cut Handwhee! ...................... 12

Fence Locks and Stops ....................... 12

Fence Tilt Scale ............................. 13

Cutter Guard ............................... 14

Fnfeed Table ............................... 14

On-Off Switch .............................. 16

BAS_IC JOINTER-PLANER OPERATION ........... 18

Feeding the Workpiece ....................... 18

Using the Hold Down/Push Blocks .............. 19

Beveling ................................... 20

MAINTENANCE .............................. 21

Replacing Cutter Blades ....................... 21

Ir_stalting Cutter Guard Spring .................. 23

Sharpening Cutter Blades ...................... 24

GENERAL MAINTENANCE .................... 25

WIRING DIAGRAM ........................... 25

LUBRICATION ............................... 25

T_OUBLE SHOOTING ......................... 26

RECOMMENDED ACCESSORIES ................ 26

REPAIR PARTS .............................. 27

o • _ • ee

motor spec faCahons and e ectrmcalrequmrements

Th_is machine is designed to use a 3450 RPM moto_ only Do not use any motor that r._r_s faster' than 3450 RPM, It is wired for operation on t10-t20 vo_ts, 60 Hz. _dter-

nating current. IT MUST NOT BE CONVERTED "TO OPERATE ON 230 VOI.TS. EVEN THOUGH SOME OF

THE RECOMMENDED MOTORS ARE DUAL VOLTAGE,

THESE CRAFTSMAN MOTORS HAVE BEEN

FOUND TO BE ACCEPTABLE FOR USE ON

THIS TOOL.

11/2 3450 110-120 12!6

1/2 3450 110-!20 1218 3/4 3450 t10-120 !219 3/4 3450 110-120 t226

CAUTION: Do not use blower or washing machine motor_ or any motor with an automatic reset overload protector

as their use may be hazardous.

CONNECTING TO POWER SOURCE OUTLET

This machine must be grounded while ip use to protect

the operator from electric shock,

Plug power cord into a 110-120V properly grounded type

outlet protected by a 15.amp, time delay or CircuitSaw_r fuse or circuit breaker.

This _x_wer tool is equipped with a 3-conductor cord and grounding type plug which has a grounding prong Jisted by

Underwriters' Laboratories Association. The ground conductor has _ green jacket and is attached to the tooi housing at one end and to the ground prong in the

attachment p)ug at the other end.

This p]u[_ requi:re_s a mating 3-conductor grounded type outJ_t as s.how_l.

if the ot_t}et you are pla:n:ning to use for this power tool is of the two pretty type DO NOT REMOVE OR ALTER

THE GROUNDING PRONG IN ANY MANNER. Use an adat_)te_ as showr_ an(t a_ways connect the grounding !ug to k r_c:twn g_ouf_{t.

It is recommende(J that you have a qualified electrician replace the TWO prong outlet with a properly grounded THREE prong out_et:.

An adapter as shown below is available for connecting plugs to 2-prong _ec{:ptactes, The green grounding lug extending

from the adapter must be connected to a permanent ground s_ch as to a properly grounded outlet box.

If you are not sure that your outlet is propet!¥ g, ounded,

have it checked by a qualified electrician,

WARNING: DO NOT PERIMIT FINGERS TO TOUCH

THE TERMINALS OF PLUGS WHEN INSTALLING OR REMOVING THE PLUG TO OR FROM THE OUTLET.

WARNING: IF NOT PROPERLY GROUNDED THIS

POWER TOOL CAN _INCUR THE POTENTIAL HAZARD OF ELECTRICAL SHOCK. PARTICULARLY WHEN USED

IN DAMP LOCATIONS IN PROXIMITY TO PLUMBING,

IF AN ELECTRICAL SHOCK OCCURS THERE ISTHE

POTENTIAL OF A SECONDARY HAZARD SUCH AS

YOU_R HANDS CONTACTING THE CUTTING BLADE.

If power cord is worn or cut, or damaged in any way, have

it replaced immediately.

3-PRONG PLUG

GROUNDED

PROPERLY __ OUTLET.,_ i

GROUNDING

PRONG

NOTE: The adapter illustrated is for use only if you already have a properW grounded 2-prong receptacle.

The use of any extension cord will ,cause some loss of power. To keep this to a minimum and to prevent over-

heating and motor burn-out, use the table below to deter- mitre the mirdmtjm wire size (A.W.G.) extension cord. Use

only 3 wire extension cords which have 3-prong grounding type plugs and 3-pole receptacles which accept the too&

plug.

Extensior_ Cord Length Wire Size A,W.G,

Up to 1OO Ft. 14

!00 200 Ft, !2

200-400 Ft. 8

CHECK MOTOR ROTATION

WARNING: FOR YOUR OWN SAFETY, MAKE SURE PLUG tS NOT CONNECTED TO POWER SOURCE OUT

LET WHEN CHA_%IGtNG MOTOR ROTATION.

The mote." must rotate COUNTERCLOCKWISE whet viewed from the s_qaft enci _o which you wil! mount th_ pu!_ey, (See page 1'O). _tf it does not, change the dire_,:._ior

acco_-diqg to the ir;structions furnished with the motor.

: 3/4,:'Wrench : : :_. :.

:3/8_,Wrench : i:::i: :

Combination Square

: :::i:: ::_ : _ .......

Model t13.20680 JointeriPlaner iS shipped ¢_mplete

'one. cartOn, but DOES NOT INCLUDE Stee| Legs.

motori ..... ..... ......

Model t13.206930 Jointer/Planer is shipped comp!lete in

one carton but INCLUDES Steel Legs, and Motor. Separate all: parts from packing materials :and check each

one with the illustration and the list of Loose Parts to make

certain all items are accounted for, before discarding any

packing material.

If any parts are missing, do not atternPt:t O assemble the

jointeriplaner, plug '_n the power Cord Or turner the switch

On until the missing parts are obtained:and are installed

correctly.

Remove the protective oil that is applied to, e!li :unpainted

metal 'surfaces. Use any ordinary household! type grease and

spot remover. CAUTION: Never use gasoline,: naptha or similar highly

::volatile solvents.

Apply a coat of automobile wax to the table.

Wip e all parts thoroughly with a clean_ dry cioth.

WARNING: ....: :

:CONNECT PLUG TO POWER :SOURCEOUTLET U:NTIL

'ALL ASSEMBLY STEPS ARE COMPLETE, AND YOU

FOR NEVER

Item

No.

A Jointer-Planer ...................... 1

B V-Belt, t/2 x 52" . .................. t

C 5/32 Setscrew Wrench ................ 1

D t/8 Setscrew Wrench ................. 1

E Motor Pulley, 2-1/2 °" Dia .............. 1

F Sliding Guard Knob .................. t

G Concave Washer ..................... 2

H Sliding Guard ...................... 1

J Sliding Guard Rod ................... 1

K Nut, 1/2 - t3 ....................... 1

L Lockwasher, 1/2 .................... t

M Lockwasher, No. 10 ................. 2

N Screw, Pan Hd. t0 - 32 x t/4 .......... 2

O Owners Manual ..................... 1

P Depth of Cut Handwheel .............. !

Q Screw, Sems, t/4 - 20 x 1-1/4 .......... 1

R Jointer-Planer Belt Guard ............. 1

S Attaching Hardware (2 Nuts, 2 Bolts)

T Motor Pulley Belt Guard .............. 1

U Belt Guard Clips .................... 3

V Belt Guard Support Bracket ........... t

W Belt Guard Support .................. 1

X 2 self tapping screws

Y Switch Key ........................ 1

Z Hold Down/Push Block ............... 2

TABLE OF LOOSE PARTS

Description Qty.

: : V

unpacking

TABLE OF LOOSE PARTS

The Following Parts Are Included With

Item

No. Description Qty.

A Leg .............................. 4

B End Stiffener ........................ 2

C Side Stiffener ...................... 4

D Motor Support ..................... !

E Motor ............................ I

Package of Miscellaneous Small Parts, No. 67035, Consisting of the Following:

F Cord Clip .......................... 2

G Hex Nut, 1/4 in. - 20

(approx. dia. of hole 1/4 in.) .......... 40

G Hex Nut, 5/16 in. - 18

(approx. alia. of hole 5/1 6 in.) ......... 7

G Hex Nut, 1/2 in. - 13

(approx. dia. of hole 1/2 in.) .......... 8

H Truss Hd. Screw, 1/4 in. - 20 x 5/8 in.

tong. (Top of screw is rounded) ........ 40

J Flat Washer (dia. of hole 11/32 in.) ...... 7

K Lockwasher, 1/4 in. External Type

(approx. alia. of hole t/4 in.) .......... 40

K Lockwasher, 5/16 in. Externa_ Type

(approx. dia. of hole 5/16 in.) ......... 7

L Carriage Bolt, 5i16in.- 18x3/4tong ... 3

M Leveling Foot ...................... 4

N Hex Hd. Screw, 5/16 in. - 18x 2in ..... 3

Model 113.206930 Only

Qnd checking

contents

G H

L M

ill , i ill i

assembly

ASSEMBLING STEEL LEGS

NOTE: Steel Legs are furnished with Model 113.206930. From among the loose parts, find the following Hardware:

40 Truss Head Screws, 1/4-20 x 5/8

40 Lockwashers, 1/4-External 40 Hex Nuts, 1/4-20 8 Hex Nuts, 1/2-t3 4 Leveling Feet

1. Assemble two (2) Side Stiffeners together using four (4) 1/4-20 Truss head screws, Iockwasher and nuts. Make

two (2) Side Stiffener assemblies. The End Stiffeners are placed on top and at each end of

Side Stiffener assemblies as shown. Atign holes, tetter coded "B °' in Side Stiffeners and End Stiffeners and

then insert t/4-20 Truss head screws through the 9/32 diameter holes letter coded "C" and install lockwashers

and nuts and then tighte_n.

2. Assemble the four (4) Legs to the Side and End

Stiffeners using t/4-20 screws, lockwashers and nuts as shown,

3. Assemble the Motor Support to the Legs with t/4-20

screws, lockwashers and nuts. Motor Support can be

assembled to either end of Leg set.

4. Install leveting feet as shown. To level Leg Set, loosen

nut on inside of leg and tL_rn nut on the outside to raise or lower feet. Adjust all four leveling feet, if necessary, and then tighten nuts o_ the inside of leg.

NOTE: These levelers are not intended for height

adjustment.

TRUSS HD. SCREW END STIFFENER

1/4-20 x 5/8

END

STIFFENER

LOCKWASHER

1/4 EXTERNAl-

..... 1/4-20 HEX

IDE STIFFENERS

° 'i

"i'"_J MOTOR SUPPORT

/ _i_ _i LEGS

i E

LEGS

MOUNTING JOINTER:PLANER

hardware:-

the following

4 Carriage 8ott,: 5./16_18 x 3/41 3 Hex Head: screws,: 5/16_18 X:2

7 Lockwashers, 5/i6 in. EXternal Type 7 Washers, 11t32 1D

7 Hex Llam Nuts, 5/16-18 2 Cord Clips

t. Loosen FENCE LOCK KNOB. Tilt fence upward and

slide it toward the pulley.

2. PoSition machine on Leg Set and align mounting holes in

machine with holes in Leg Set letter coded °'A'. Mount with three (3) 5/1 6-18 x 2" Long Hex Head Screws.

3. Place a flat washer, a lock washer and a nut on each screw from underneath the stand and tighten.

4. PlaCe handwheet on shaft aligning flat surfaces on shaft

with flat surfaces on handwheel.., attach with 1-1/4 in.

screw.

1/4-20 TRUSS SIDE STIFFENER HEAD SCREW

____ JO INTER/PLANER

HEXNUT W H

FENCE LOCK KNOB

HEAD SCREW

STIFFENER

1-1/4 IN. SCREW

DEPTH OF CUT HANDWHEEL

.,_MOTOR SUPPORT AT THIS END ----_

CHECK! NG CUTTER BLADES AND SCR EWS

TOOLS NEEDED

5/32" and 1/8" Setscrew Wrenches (furnished

Jointer),

Lead Pencil

Short straight edge (or head of combination square)

1. Insert pencil in space at end of cutterhead to hold cutterhead guard open.

2. Lower the infeed table with the Depth of Cut Handwheet.

3. Rest the straight edge on edge on the surface of outfeed table so it extends across the opening between the

tables, at three positions: near each end and at the middle of the cutter blade_

4. ROtate the cutterhead by grasping the 2" dia. driven pulley and make-sure each knife ticks (touches) the straight edge at all three positions. If not, follow

procedure under "REPLACING CUTTER BLADES" on ppg. 21 and 22.

with

5/32 IN. SETSCREW

OUTFEED TABLE

WEDGE

PENCI L

5. If a cutter blade adjustment is not required, check each

locking: screw of each wedge (5/32" setscrew wrench) and tighten if necessary. Hold the pulley while tightening screws and be careful that your fingers do not

slip off the wrench."

WRENCH

CUTTER GUARD

iNSTALLING SLIDING GUARD

PARTS NEEDED

1 Sliding Guard

I Sliding Guard Knob

t Sliding Guard Rod 2 Sliding Guard Washers (one side of washer is concave)

1 Hex. Nut 1/2 in.* t3 1 Sl_it lockwasher 1/2 in.

2 E×t, tooth Iockwashers 2 10-32xl/4 Pan Hd. Screws

t. Screw nut alt the way onto long end of rod.. , place

1/2 in. lockwasher next to nut.

2. Screw rod all the way into Jointer with short end up... tighten nut.

1/2 IN. HEX NUT

SLIDING GUARD

3, Attach sliding guard to fence with two machine screws

and lockwashers,

4. Place one Sliding Guard Washer, concave side DOWN on

support rod.

5. Drop sliding guard onto rod.., place other washer, con-

cave side UP on rod , , . screw on Sliding Guard Knob,

MOUNTING RECOMMENDED CRAFTSMAN MOTOR AND BELT GUARDS

See page 5 for recommended motors.

PARTS NEEDED

4 carriage bolts, 5]16-18 x 3/4 in., flat washers, lock washers and nuts.

1 Jointer Planer Belt Guard 1 Motor Pulley Belt Guard

1 Belt Guard Support ! Belt Guard Support Bracket

SLIDING GUARD KNOB

10-32xl/4 SCREWS EXT. TOOTH

LOCKWASHERS

3 Belt Guard Clips

1 Motor Pulley, 2-t/2 in. dia. 1 V-Belt

2 Pan Head Screws 10 - 32 x t/2 in, 2 Hex, Hd. Screws 1/4 - 20 x 1/2 in.

2 Hex, Nuts 1/4- 20

TOOLS NEEDED

Medium Screwdriver 5/32 in. Setscrew Wrench (furnished with Jointer)

1/2 and 7/!6 in, Wrenches

WASHE R

(CONCAVE SIDE UP)

1, Place motor on your workbench with 5/8 in. dia, shaft

(with key way) facing you.

2. Attach guard support to bracket with two screws.

NOTE: The holes in the bracket are not threaded, but the screws are "thread cutting screws" and win cut a thread as they are tightened,

5/:8 IN. DIA, SHAFT

BELT GUARD SUPPORT BRACKET

PAN HD. SCREWS

BELT GUARD

SUPPORT

C_i _:!:iin:motoKpdiley and:place:Pulley:iOn h_ f|U_h:! _itt+ end i: sfiaf_ii ihSertl motif:r:

The motor rn_:$ _iewed from +PULLEY end:

• ':

DIRECTION

ROTATION

5/32 IN.

SETSCREW

WRENCH

1_ Place m0tor on your workbench or on floor.

2. Stand clear of motor and plug cord into a properly

grounded outlet (See page 5). Notice rotation of pulley,

If it is:not= turning COUNTERCLOCKWISE, REMOVE plug from outlet, and change rotation of motor accord- ing to instructiOns furnished with motor;

WARNING: FOR YOUR OWN SAFETY, MAKE SURE PLUG iS NOT CONNECTED TO POWER SOURCE OUT-

LET WHEN CHANGING ROTATION.

MOUNTING MOTOR

1. Find four 5/16_t8 x 3/4" carriage bolts, flat washers, and lockwasher and nuts.

2, Attach motor by inserting carriage bolts through slots in

motor base and through slots in motor support. Place a

fiat washer, 10ckwasher and nut on each carriage bolt,

but DO NO:F TIGHTEN nut.

FLUSH HERE

MOTOR

SHAFT

KEY

I == ::;1

MOTOR MOUNT BRACKET

..... j ,

6, Install three clips on belt guard 90° apart with long tabs

pointing AWAY from round opening.

7, Insert belt into open end of guard,

BELT

_*_BELT GUARD CLIPS

(90° APART)

+ 22 hidden pages